Jfi2089aes Parts

This refrigerator dispenser solenoid converts electrical power into a pull on the dispenser linkage so the ice-dispensing mechanism opens and closes correctly. Replacing a weak or stuck solenoid restores consistent dispensing and reduces frost and warm-air leaks at the chute. What it does:

• Actuates the ice dispenser mechanism (e.g., chute door/gate) when the dispenser is engaged
• Helps the chute seal properly when not dispensing
• Resolve issues like no ice dispensing, door not opening/closing, loud buzz/click with no movement, or frost/condensation at the dispenser

• 1 solenoid

• Disconnect power before servicing
• Access the solenoid in the dispenser/freezer-door assembly; remove trim carefully to avoid breaking tabs
• Note wire positions and transfer any linkage or bracket from the original part if reused
• Restore power and test operation before final reassembly

This fill cup insert channels incoming water into the correct area during the appliance's fill cycle, acting as a small guide/funnel. Replacing a damaged or missing insert helps prevent splashing, misdirected flow, and leaks around the fill point. What it does:

• Directs water from the fill tube into the intended receptacle
• Helps reduce splashing, overspray, and misfills during the fill cycle
• Restores proper alignment of the water stream
• Common symptoms: leaks or drips near the fill area, water missing its target, visible cracks/warping on the insert

• 1 fill cup insert

• Disconnect power and shut off the water supply before servicing
• Access the fill area; remove the old insert and retain any screws/clips
• Position the new insert under the fill tube, ensuring correct orientation; secure as designed
• Restore water/power and run a test fill; check for proper flow and leaks

This replacement glass fits the pantry cover above the full-width deli/pantry drawer in your refrigerator, restoring a sturdy shelf surface and helping seal the bin below. Replace damaged or missing glass to keep items supported and the drawer operating as designed.

• Creates the rigid shelf surface over the pantry/deli drawer
• Helps the cover seal the bin for more consistent conditions in the drawer
• Replace if the glass is cracked, shattered, bowed, or missing
• Can resolve a wobbly shelf, poor cover support, or gaps over the pantry bin

• Disconnect power and wear cut-resistant gloves when handling glass
• Remove food items; lift/release any trim and slide the old glass out of the cover frame
• Clean the frame channels; slide the new glass fully into place without forcing
• Reinstall trim and drawer; verify the cover opens/closes and the shelf is stable

This target ring is a small trim piece that restores the original fit and appearance around a control button or panel opening. Replacing a damaged ring helps ensure clean button engagement and a finished look. What it does:

• Serves as the trim/target around a control button or panel opening
• Keeps the button aligned for consistent engagement and operation
• Restores finished appearance when the original ring is cracked, warped, or missing
• Prevents debris from collecting around the control area

• One replacement target ring

• Disconnect the appliance from power before attempting replacement
• Usually installs by snapping into place or securing with retained fasteners — handle gently to avoid breaking tabs
• Confirm proper button movement and secure fit before returning appliance to service

This CRSP brace is a replacement support component that helps stabilize and align the 36-inch crisp/crisper assembly for proper drawer operation and fit. Restores secure mounting and reduces movement or vibration of the crisp area. What it does:

• Provides structural support for the crisp/crisper assembly so drawers and panels sit squarely
• Helps stop sagging, misalignment, rattling or binding of the crisp area
• Maintains correct spacing for smooth opening and closing
• Replaces worn or damaged braces that compromise stability

• One CRSP brace

• Disconnect power to the appliance before beginning work to avoid electrical or mechanical hazards
• Basic hand tools are typically required; retain original fasteners
• Follow OEM service literature for exact removal and installation steps and torque recommendations
• Support panels or drawers while removing/installing the brace to prevent damage or injury

This exterior glass support holds the oven door's outer glass securely in place so the door stays aligned and the glass doesn't shift or rattle during use. Replaces a cracked, broken or missing support to restore proper door fit and function. What it does:

• Secures the outer oven door glass to the door frame so the glass remains stable
• Prevents glass movement, vibration, or noise when the door is opened or closed
• Helps maintain proper door alignment and a consistent seal
• Common symptom: loose, rattling or misaligned outer door glass

• One exterior glass support

• Disconnect power (and gas, if applicable) before starting any oven door repair
• Handle glass carefully; wear safety gloves and eye protection to avoid injury
• Installation usually requires removing the oven door panel and fastening the support with existing screws/clips

This replacement screw secures panels, trim pieces and small assemblies so covers and components stay aligned and rattle-free. It's a simple, direct fastening part used when an original screw is missing or damaged. What it does:

• Fastens panels, trim, control housings and other small components to the appliance chassis
• Replaces missing, worn or stripped screws that cause loose panels or rattling noises
• Restores correct alignment of covers and trims after service or disassembly
• Provides a direct, hardware-level repair instead of temporary fixes

• Disconnect power (and gas, where applicable) and ensure the appliance is cool before starting.
• Use the correct screwdriver bit and turn until snug; do not overtighten to avoid stripping threads or damaging parts.
• Keep removed hardware for reference; replace like-for-like if threads or inserts are damaged.
• Wear eye protection and gloves when working on appliances.

The Wiring Harness is an OEM part for Whirlpool refrigerators. It ensures proper connectivity between various parts of the electrical system.

The wiring harness provides a secure and reliable connection for power supply and communication within the refrigerator. It allows for efficient operation of the refrigerator's functions, such as temperature control, ice making, and defrosting.

A bad wiring harness can occur due to factors like wear and tear, accidental damage, or electrical faults. If you notice symptoms such as intermittent power loss, malfunctioning controls, or erratic behavior of the refrigerator, it may be time to replace this part.

Symptoms of a bad wiring harness include:

• Intermittent power loss
• Malfunctioning controls
• Erratic behavior of the refrigerator

Restore your Whirlpool refrigerator by replacing the faulty or damaged wiring harness with this genuine OEM part.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

A right-side top hinge cover that restores your appliance's finished appearance and protects the hinge mechanism from dust and debris. Fits over the hinge area to hide hardware and prevent snags or buildup. What it does

• Covers and protects the top hinge assembly to keep moving parts free of lint, dirt, and moisture
• Restores a clean, finished look when the original cover is cracked, broken, or missing
• Helps prevent clothing or items from catching on exposed hinge hardware
• Matches the original mounting points for a secure, low-profile fit

• One right-side top hinge cover

• Disconnect power before starting work and follow basic electrical safety
• Typically installs by removing the top or lift panel and snapping or fastening into the hinge area; keep all mounting screws
• If cover is brittle or fragmented, remove all remnants before fitting the new piece to ensure a flush install
• Use hand tools; avoid overtightening fasteners which can crack the replacement

This seal strip replaces a worn or damaged door gasket edge to restore a proper seal and help the appliance maintain temperature and operate quietly. It's a direct-fit service part used where a continuous seal is required. What it does:

• Provides a flexible barrier along the door/frame to reduce air leaks and heat/cold loss
• Helps prevent moisture buildup and improves energy efficiency when sealing is restored
• Reduces rattling and vibration caused by a compressed or torn seal edge
• Commonly replaced when the strip is torn, missing, or no longer adheres properly

• One seal strip

• Disconnect power to the appliance before servicing to avoid electrical or burn hazards
• Clean and dry the mounting surface; remove old adhesive or residue for best adhesion
• Align the strip carefully and press firmly; allow any adhesive to cure per manufacturer instructions