Jgbs60dekbb Parts

The Valve Control Assembly is an OEM component specially designed for GE gas wall ovens and ranges. Located at the rear of the unit, it houses the gas valve, piezo igniter, and control logic that regulates the flow of fuel to each active burner.

Symptoms of a bad valve control assembly include:  

• Unstable or irregular burner flame heights and patterns
• Burners failing to ignite or stay lit as intended 
• Gas leak smells detected around rear connection fittings
• Error codes or dysfunction of baked-on cleaning modes

As a critical safety device, the valve assembly must operate precisely cycle after cycle. Causes like thermal stress or electrical faults can induce failures over the years. This genuine GE replacement facilitates dependable and code-approved gas control. Compatible GE gas wall oven and range brands including Monogram ensure trusted and safe daily cooking performance.
 

This anti-tip bracket secures the rear of your range to the floor or wall so the rear leveling leg locks in place. Replacing a missing or damaged bracket helps prevent tipping and keeps the appliance stable during everyday use.

• Anchors the range to a fixed point; rear leveling leg engages the bracket
• Helps prevent forward tipping when weight is placed on an open oven door
• Reduces rocking or sliding during cooking or cleaning
• Replace if the bracket is missing, bent, corroded, or the unit fails the anti-tip check

• Disconnect power and, if applicable, shut off gas before servicing
• Pull the range straight out; position the bracket per your installation manual/template
• Fasten the bracket securely to floor or wall studs using hardware appropriate for your surface
• Slide the range back so the rear leg fully engages the bracket; perform the anti-tip test from your manual

Includes 12 washers.

This electronic oven control board regulates and coordinates oven functions on gas ranges—driving the display, processing keypad inputs, and switching relays—so you can set temperatures and cycles reliably. Replacing a failing board restores responsive controls and consistent heating. What it does:

• Controls bake and broil ignition and temperature regulation in gas ovens
• Interprets keypad inputs and updates the display
• Switches power through onboard relays to igniters/valves as directed by sensors
• Common failure symptoms: blank or erratic display, unresponsive controls, oven won't start or heat, or recurring control error codes

• 1 electronic control board assembly

• Disconnect power at the breaker and shut off gas before servicing
• Use ESD precautions; handle the board by its edges
• Access the board behind the control panel; photograph wiring and move connectors one at a time
• Reuse existing mounting hardware; restore power and test oven functions after reassembly

• A faulty oven temperature sensor or keypad/touch interface can mimic control-board issues; test related components before replacement.

This round gas valve controls flow to a surface burner, providing smooth flame adjustment and reliable shutoff. Replace a worn valve to restore precise burner control and safe operation on your gas range or cooktop.

• Regulates gas to the burner as the control knob turns, from low simmer to full flame
• Common symptoms: burner won't light though the igniter sparks, flame won't adjust or shut off, gas odor near the knob, or a stiff/stripped valve stem
• Services one burner position; multiple valves are used on many gas ranges/cooktops
• Installs in the burner manifold/orifice holder location specified by the manufacturer

• Disconnect power and shut off the gas supply before servicing
• Note stem orientation; transfer fittings/brackets from the original valve as needed and use approved thread sealant where specified
• After installation, leak-test all joints with an approved solution before restoring gas
• Verify proper ignition and flame adjustment on the burner after replacement

The Clip Igniter is an OEM replacement part for GE ranges.

This GE OEM replacement is also compatible with some Hotpoint, Sears Kenmore, and RCA models. 

The outer door glass is an OEM part for GE ovens. It serves as the protective barrier for the oven door, providing insulation and a visually appealing finish. It is designed to maintain the desired temperature inside the oven while keeping the exterior cool to the touch.

A bad outer door glass can result in issues such as cracks, shattered glass, or loose trim. Causes of a bad assembly can include accidental impacts, exposure to extreme temperatures, or wear and tear over time.

Symptoms of a bad outer door glass include:

• Visible cracks or shattered glass on the oven door
• Loose or damaged trim around the glass panel
• Heat escaping from the oven door
• Difficulty in cleaning or removing stains from the glass

Replace your worn-out or damaged outer door glass with this genuine OEM GE part to restore your oven. 

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

Color: Bisque

The Valve Control Assembly is an OEM component specially designed for GE gas wall ovens and ranges. Located at the rear of the unit, it houses the gas valve and igniter that regulates the flow of fuel to each active burner.

Causes of a bad valve control assembly include cracking or fractures of internal gas tubing from repeated thermal expansion and contraction over many years. Damage may also occur from impact or rough handling during appliance installation.  

Symptoms of a bad valve control assembly:

• Burners failing to ignite or stay lit as intended
• Gas leak smells detected around rear connection fittings  
• Error codes or displays showing blocked valves
• Inability to select or operate specific burners/oven functions

This genuine GE replacement facilitates code-compliant performance through an engineered life-cycle of on/off cycles. Compatible GE, Monogram, and other premium brand gas models are safely supported.
 

This factory fastener secures internal components or panels in your appliance. Replacing a missing or stripped screw restores a snug fit, helps prevent vibration or rattling, and keeps assemblies aligned for proper operation.

• Secures brackets, panels, or internal components to the frame
• Replaces missing, rusted, or stripped hardware
• Helps reduce rattling, vibration, or loose-fit issues
• Maintains proper alignment and fit of assemblies

• Disconnect power before servicing
• Use the correct driver to avoid stripping the screw head
• Install in the original location; match thread and length to the original
• Tighten until snug; do not overtighten, especially into plastic or thin metal

The outer door glass is an OEM part for GE ovens. It serves as the protective barrier for the oven door, providing insulation and a visually appealing finish. It is designed to maintain the desired temperature inside the oven while keeping the exterior cool to the touch.

A bad outer door glass can result in issues such as cracks, shattered glass, or loose trim. Causes of a bad assembly can include accidental impacts, exposure to extreme temperatures, or wear and tear over time.

Symptoms of a bad outer door glass include:

• Visible cracks or shattered glass on the oven door
• Loose or damaged trim around the glass panel
• Heat escaping from the oven door
• Difficulty in cleaning or removing stains from the glass

Replace your worn-out or damaged outer door glass with this genuine OEM GE part to restore your oven. 

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

This economic nut is a small replacement fastening nut that restores secure connections for appliance components. It replaces worn or missing hardware so panels and internal parts stay firmly seated and reduce vibration. What it does:

• Secures components and panels by threading onto the matching stud or bolt to hold assemblies in place
• Prevents loose or rattling panels and hardware caused by a missing or damaged nut
• Restores proper fit for user-accessible panels and internal brackets where this nut is specified
• Simple hardware replacement to regain stable mechanical connections

• Disconnect power and water (if applicable) and follow basic electrical safety before servicing the appliance
• Use the matching size wrench or socket; thread-on by hand first to avoid cross-threading, then snug—do not overtighten
• Inspect mating stud or bolt for damage; replace hardware that is stripped, corroded, or deformed

This surface burner grate assembly replaces the hairpin-style grate used on select gas ranges and cooktops. It restores a stable, level cooking surface so pots and pans sit securely over the burner.

• Supports cookware over the flame and helps center pots for even heating
• Hairpin profile and footprint provide proper burner clearance on compatible models
• Replaces a cracked, warped, chipped, or broken grate that rocks or won't sit flat
• Common symptoms: unstable cookware, uneven pan support, or flaking finish

• Turn off all burners and allow the cooktop to cool completely before servicing
• Lift off the old grate and clean the cooktop support area
• Position the new grate so all feet rest flat and it sits level
• Verify proper clearance to burner caps and igniters before use

The Round Valve Burner 140 is an OEM part for GE gas ranges. It regulates gas flow to a tubular burner ring, enabling tempered cooking performance. 

Causes of failure include mineral buildups obstructing valve ports, worn sealing edges letting gas escape, or broken internal components.

Symptoms of a bad round valve burner are: 

• Inaccurate or indistinct burner flame patterns
• Inability to maintain consistent flame heights 
• Responsiveness issues adjusting burner temperature

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore gas range models.

This orifice spud meters gas to a burner in your range or cooktop. Replacing a clogged or damaged spud helps restore correct flame size and reliable ignition for consistent cooking performance.

• Regulates gas flow from the valve to the burner head for proper combustion
• Helps restore consistent flame height and even heating on the burner
• Sized for the burner rating and fuel type specified by your model; always match the correct part

• Disconnect power and shut off gas supply; allow the appliance to cool completely before servicing.
• Access the burner orifice and replace with the correct, model-specified spud using an appropriate wrench; do not overtighten.
• Restore gas and check all connections for leaks with a soap-and-water solution.
• Use only the spud specified for your fuel type (NG or LP); do not attempt conversion without the approved kit and instructions.

The range Overlay (T09) is an OEM part for GE gas ranges. It is a cosmetic layer applied over control panels to enhance aesthetics and protect sensitive electronics underneath.

Causes of a bad overlay include normal fatigue from exposure plus unexpected handling incidents.

Symptoms of an aging overlay include:

• Scuffs, cracks or bubbles appearing on glossy surfaces  
• Fraying or peeling edges exposing underlying panels
• Discoloration detracting from the appliance's appearance
• Loss of ability to safeguard delicate components

This GE part also fits Hotpoint, RCA and select Kenmore models.