Jgp33weh3ww Parts

This replacement screw secures appliance components so panels, brackets, and trim stay tight and aligned. Use it to replace a missing, stripped, or rusted fastener and restore a solid, rattle-free fit in the affected assembly.

• Fastens parts to the chassis/frame or mounting brackets
• Replaces lost, damaged, or corroded hardware
• Can help address loose or vibrating panels and minor misalignment
• Maintains a secure attachment during normal operation

• Disconnect power before servicing; for gas appliances, also shut off the gas supply
• Match the screw to the original location and reuse any clips or washers if present
• Start threading by hand to avoid cross-threading; tighten snugly without overtightening
• Repair/replace damaged receiving threads or clip for proper hold

Replacement fastener used to secure appliance components. If a screw is missing or damaged, panels and brackets can loosen or rattle. Installing a new screw restores a tight fit and helps keep parts properly aligned.

• Fastens panels, brackets, or internal components as designed for the model
• Replaces missing, stripped, or corroded hardware
• Helps reduce vibration/rattling and restores proper fit
• Maintains alignment and a secure assembly after service

• Disconnect power; shut off gas if applicable before servicing
• Support components while removing/installing fasteners
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Replace all required screws in a location for even clamping and proper fit

This circuit board mounting bracket secures an electronic board or module inside the appliance. It prevents movement, vibration damage, and wiring interference so the component stays correctly positioned for reliable operation.

• Mounts and supports a small circuit board or module within the chassis
• Maintains proper spacing and alignment to reduce chafing or electrical short risks
• Replace if bent, cracked, or missing tabs, or if it no longer holds the board securely
• Common signs include a loose/rattling board, visible bracket damage, or intermittent operation when the panel is bumped

• Disconnect power at the breaker; shut off gas supply if applicable
• Remove the necessary access panel(s) to reach the board and bracket; note orientation and wiring
• Transfer the board/module to the new bracket and reinstall using existing hardware
• Watch for sharp metal edges; route wires to avoid pinching and verify clearances before restoring power

This head burner main is the primary gas burner head used on compatible gas ranges to direct and distribute the flame for proper cooking. It replaces a damaged or corroded burner head to restore even heating performance. What it does:

• Directs gas to the cooktop for ignition and controlled flame distribution
• Helps maintain even heat across the cooking surface for consistent results
• Can resolve symptoms like uneven flame, visible damage, or poor ignition at the burner
• Works with the burner cap and valve assembly as part of the burner system

• Turn off gas supply and power to the appliance before starting any work
• Remove grates and burner caps to access the burner; follow OEM disassembly guidance
• Replace only with the exact part number to ensure proper fit and function

18K Simmer

This small cooktop bracket secures designated components beneath the cooktop surface, keeping them properly positioned and stable. Replace a damaged or missing bracket to restore alignment and reduce movement or rattling during use.

• Provides mounting support for specific under-top components, per model design
• Helps maintain proper alignment and stability of cooktop parts
• Replace when visibly bent, cracked, or corroded

• Disconnect power; for gas models, also shut off gas and allow the unit to cool
• Remove surface components as required (grates/caps/heads for gas; elements/panels for electric) to access under the top
• Lift or remove the cooktop as directed in your model's service information and secure the new bracket with existing hardware
• Reassemble, verify alignment, and for gas units check for leaks if any gas connections were disturbed

Restore easy, precise control with this replacement control knob. It replaces a worn, cracked, or loose knob so you can confidently adjust your appliance's settings and get back to cooking without wobble or slip.

• Mounts on the control valve or switch shaft to select and adjust heat levels
• Replaces knobs that are cracked, stripped, loose, missing, or hard to read
• Helps when the knob won't stay on or spins without turning the shaft
• Restores original look and positive, secure feel during use

• Disconnect power and allow all surfaces to cool before servicing; if working near gas components, shut off the gas supply
• Pull the old knob straight off the shaft
• Align the new knob with the shaft shape/flat and push straight on until fully seated—do not force
• Test each control for smooth operation and proper alignment

This replacement valve kit restores proper flow control in compatible GE appliances, helping resolve failures related to supply, dispensing or leaks. It's a direct-replacement style assembly intended to return the affected system to normal operation. What it does:

• Regulates flow to the appliance's system to enable normal filling, dispensing or operation
• Replaces worn seals and moving valve components that can cause intermittent function
• Stops or reduces leaks and unintended flow when the original valve assembly fails
• Helps correct symptoms such as no fill/dispense, intermittent operation, or persistent leaking

• Always disconnect power and, if applicable, shut off the water and/or gas supply before starting
• Handle components carefully; use manufacturer-recommended seals, gaskets and mounting hardware
• Test for leaks and correct operation after installation

This is a direct replacement control knob for your appliance. It restores a secure, accurate feel when turning the control after the original knob becomes cracked, stripped, loose, or goes missing. What it does:

• Attaches to the control shaft so you can turn and set the heat on the appliance
• Replaces knobs that are broken, cracked, stripped, loose, or missing
• Can help when the knob spins without engaging the stem or falls off
• Restores intended operation and tactile feedback of the control

• One control knob

• Disconnect power; for gas units, also shut off gas before servicing
• Pull the old knob straight off the control shaft—do not pry against the panel
• Align the new knob with the shaft shape and press straight on until fully seated
• Turn the control to verify smooth operation and proper engagement

Replacement burner wire harness that restores the ignition wiring connection for a gas range surface burner, helping re-establish consistent sparking and reliable burner ignition for safe cooking operation. What it does:

• Provides the electrical connections between the burner igniter/spark electrode and the range's ignition module/control.
• Replaces damaged, cut, or frayed wiring that can cause no-spark, intermittent ignition, or continuous clicking at the burner.
• Routes and secures ignition wires to keep connections stable and reduce heat/rub-related failures.
• Helps the ignition system deliver consistent sparks so burners light reliably.

• Disconnect electrical power and shut off the gas supply before beginning any service.
• Compare the new harness to the original; transfer and reconnect terminals one-to-one and secure any routing clips or fasteners.
• Route wires away from hot surfaces and sharp edges; avoid stretching or pinching the harness.

Clip Electrode that secures a spark/flame electrode to the burner assembly, keeping the igniter properly positioned for reliable ignition. Replaces a worn or broken retainer to help restore consistent spark alignment and lighting. What it does:

• Secures the spark/flame electrode to the burner/orifice holder so the electrode stays correctly positioned.
• Maintains electrode gap and alignment to support a strong, consistent spark for ignition.
• Helps address ignition symptoms such as weak or intermittent spark, clicking without ignition, or a burner that won't light.
• Replaces a bent, broken, or missing retainer without replacing the full electrode assembly.

• Always turn off power to the appliance and shut off the gas supply before servicing ignition components.
• Handle the electrode and its ceramic insulator carefully—they can be brittle; use needle-nose pliers to seat the clip if needed.
• After installing, verify electrode alignment and gap; improper alignment can prevent ignition.

18K

A replacement burner valve cover that protects and conceals the gas valve assembly on compatible ranges, helping keep valve components clear of spills and debris for more reliable burner operation. What it does:

• Covers and protects the gas valve area from food, moisture and spills.
• Helps prevent debris from interfering with valve knobs and internal valve parts.
• Can reduce intermittent ignition or burner performance issues caused by contamination.
• Restores the finished appearance around the valve for safer, cleaner operation.

• Always shut off the gas supply and unplug the appliance before servicing.
• Use basic hand tools; handle the valve area gently to avoid disturbing fittings or tubing.
• After installation, check for gas leaks with a soapy-water solution or a proper leak detector—do not use an open flame.

Replacement surface unit control knob in white helps restore proper grip and accurate burner heat selection on stovetop ranges, improving control, safety, and overall appearance during everyday cooking. What it does

• Replaces a cracked, melted, loose, or missing knob so you can select burner heat settings safely and predictably.
• Fits standard splined control shafts used on many gas and electric cooktop infinite-switch controls.
• Restores tactile feedback and clear pointer position for precise temperature selection.
• Simple cosmetic upgrade that refreshes the look of the cooktop control panel.

• Disconnect power to the appliance before servicing; for gas ranges also shut off the gas supply if applicable.
• Remove the old knob by pulling it straight off the control shaft; align the splines and push the replacement knob firmly onto the shaft until fully seated.
• After installation, restore power and test each burner control to confirm proper operation.

Please note: These are a dark grey replacing light grey

This is the screw that secures the burner valve to the appliance, keeping the valve and associated controls fastened for reliable operation. Replaces a worn or missing mounting fastener to restore proper valve alignment and support. What it does:

• Secures the burner valve assembly to the appliance frame or manifold
• Keeps valve position stable to help maintain reliable burner operation
• Helps prevent movement that can cause loose connections or intermittent function
• Used when original screw is stripped, missing, or corroded

• One burner valve mounting screw

• Turn off power and gas supply to the appliance before starting any repair
• Use the correct size driver and avoid over-tightening to prevent stripping the screw or damaging the valve
• Confirm valve and surrounding components are properly aligned before final tightening