Jgp633setss Parts

This bracket secures the cooktop/main top to the appliance chassis to keep the surface stable and properly aligned. Replacing a bent or missing bracket can eliminate looseness, rattles, and visible gaps so the top seats correctly.

• Anchors the cooktop/main top to the frame
• Maintains proper spacing and alignment of the top
• Helps prevent vibration and movement during use and cleaning
• A damaged or missing bracket can cause a loose, uneven, or rattling cooktop

• Disconnect power and, for gas units, shut off the gas supply before servicing
• Access the bracket location per your model's service procedure (top may need to be lifted or removed)
• Transfer and reuse mounting screws/clips from the original bracket if required
• Install in the same orientation, check alignment, and tighten fasteners securely before restoring service

This control knob seal fits around the control shaft opening on your range or cooktop to close the gap under the knob. It helps block spills and debris from entering the control area and keeps the console looking clean and finished.

• Forms a barrier between the knob/valve shaft and the control surface
• Helps prevent liquids, crumbs, and grease from seeping into the control cavity
• Restores a tidy appearance; replaces cracked, shrunken, or missing seals
• Typical signs of wear: visible damage, gaps around the knob, or residue appearing beneath the panel after spills

• Disconnect power and, if applicable, shut off gas; allow the appliance to cool
• Pull the knob straight off the shaft and remove the old seal
• Clean the area; seat the new seal flat around the shaft—avoid side pressure on the valve stem
• Reinstall the knob and verify smooth operation and proper seal seating

This economic nut is a small replacement fastening nut that restores secure connections for appliance components. It replaces worn or missing hardware so panels and internal parts stay firmly seated and reduce vibration. What it does:

• Secures components and panels by threading onto the matching stud or bolt to hold assemblies in place
• Prevents loose or rattling panels and hardware caused by a missing or damaged nut
• Restores proper fit for user-accessible panels and internal brackets where this nut is specified
• Simple hardware replacement to regain stable mechanical connections

• Disconnect power and water (if applicable) and follow basic electrical safety before servicing the appliance
• Use the matching size wrench or socket; thread-on by hand first to avoid cross-threading, then snug—do not overtighten
• Inspect mating stud or bolt for damage; replace hardware that is stripped, corroded, or deformed

This replacement burner grate assembly restores a stable, level cooking surface so your cookware sits securely over the burners. Replace a worn, cracked, or missing grate to improve safety and everyday cooking performance.

• Supports pots and pans at the correct height over the flame for consistent heating
• Keeps cookware stable to help prevent rocking or tipping
• Replaces damaged, warped, or broken grates that can compromise results
• Refreshes the cooktop's appearance after heavy wear or discoloration

• Allow the cooktop and old grate to cool completely before handling
• Lift off the old grate and clean the support area of spills or debris
• Set the new grate in place, aligning feet/locator tabs so it sits flat without wobble
• Avoid dropping or sliding the grate to prevent chipping or surface scratches

This burner wire harness connects the range/oven ignition system components so the burner safely receives the correct spark or hot-surface signal. It replaces a damaged or worn harness to restore reliable ignition performance. What it does:

• Routes electrical connections from the igniter/spark module to the burner assembly
• Enables ignition sparks or hot-surface signals to reach the burner for reliable lighting
• Can stop symptoms such as burners failing to light, erratic or intermittent ignition, or continuous clicking
• Helps prevent loose or shorted wiring that can cause ignition faults

• Disconnect electrical power and shut off gas supply before starting any repair
• Label or photograph original wiring locations to ensure correct reconnection
• Route the harness clear of direct heat and moving parts; secure with original clips or ties

Replacement fastener used to secure appliance components. If a screw is missing or damaged, panels and brackets can loosen or rattle. Installing a new screw restores a tight fit and helps keep parts properly aligned.

• Fastens panels, brackets, or internal components as designed for the model
• Replaces missing, stripped, or corroded hardware
• Helps reduce vibration/rattling and restores proper fit
• Maintains alignment and a secure assembly after service

• Disconnect power; shut off gas if applicable before servicing
• Support components while removing/installing fasteners
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Replace all required screws in a location for even clamping and proper fit

This circuit board mounting bracket secures an electronic board or module inside the appliance. It prevents movement, vibration damage, and wiring interference so the component stays correctly positioned for reliable operation.

• Mounts and supports a small circuit board or module within the chassis
• Maintains proper spacing and alignment to reduce chafing or electrical short risks
• Replace if bent, cracked, or missing tabs, or if it no longer holds the board securely
• Common signs include a loose/rattling board, visible bracket damage, or intermittent operation when the panel is bumped

• Disconnect power at the breaker; shut off gas supply if applicable
• Remove the necessary access panel(s) to reach the board and bracket; note orientation and wiring
• Transfer the board/module to the new bracket and reinstall using existing hardware
• Watch for sharp metal edges; route wires to avoid pinching and verify clearances before restoring power

This small cooktop bracket secures designated components beneath the cooktop surface, keeping them properly positioned and stable. Replace a damaged or missing bracket to restore alignment and reduce movement or rattling during use.

• Provides mounting support for specific under-top components, per model design
• Helps maintain proper alignment and stability of cooktop parts
• Replace when visibly bent, cracked, or corroded

• Disconnect power; for gas models, also shut off gas and allow the unit to cool
• Remove surface components as required (grates/caps/heads for gas; elements/panels for electric) to access under the top
• Lift or remove the cooktop as directed in your model's service information and secure the new bracket with existing hardware
• Reassemble, verify alignment, and for gas units check for leaks if any gas connections were disturbed

Restore easy, precise control with this replacement control knob. It replaces a worn, cracked, or loose knob so you can confidently adjust your appliance's settings and get back to cooking without wobble or slip.

• Mounts on the control valve or switch shaft to select and adjust heat levels
• Replaces knobs that are cracked, stripped, loose, missing, or hard to read
• Helps when the knob won't stay on or spins without turning the shaft
• Restores original look and positive, secure feel during use

• Disconnect power and allow all surfaces to cool before servicing; if working near gas components, shut off the gas supply
• Pull the old knob straight off the shaft
• Align the new knob with the shaft shape/flat and push straight on until fully seated—do not force
• Test each control for smooth operation and proper alignment

This is a direct replacement control knob for your appliance. It restores a secure, accurate feel when turning the control after the original knob becomes cracked, stripped, loose, or goes missing. What it does:

• Attaches to the control shaft so you can turn and set the heat on the appliance
• Replaces knobs that are broken, cracked, stripped, loose, or missing
• Can help when the knob spins without engaging the stem or falls off
• Restores intended operation and tactile feedback of the control

• One control knob

• Disconnect power; for gas units, also shut off gas before servicing
• Pull the old knob straight off the control shaft—do not pry against the panel
• Align the new knob with the shaft shape and press straight on until fully seated
• Turn the control to verify smooth operation and proper engagement

Clip Electrode that secures a spark/flame electrode to the burner assembly, keeping the igniter properly positioned for reliable ignition. Replaces a worn or broken retainer to help restore consistent spark alignment and lighting. What it does:

• Secures the spark/flame electrode to the burner/orifice holder so the electrode stays correctly positioned.
• Maintains electrode gap and alignment to support a strong, consistent spark for ignition.
• Helps address ignition symptoms such as weak or intermittent spark, clicking without ignition, or a burner that won't light.
• Replaces a bent, broken, or missing retainer without replacing the full electrode assembly.

• Always turn off power to the appliance and shut off the gas supply before servicing ignition components.
• Handle the electrode and its ceramic insulator carefully—they can be brittle; use needle-nose pliers to seat the clip if needed.
• After installing, verify electrode alignment and gap; improper alignment can prevent ignition.

This switch harness assembly connects the appliance's microswitches to the main wiring, providing reliable electrical paths and proper safety signaling. Replacing a damaged harness restores consistent switch input so the unit can start and run as intended.

• Routes power and signals between safety/interlock switches and the control or main harness
• Helps resolve issues such as no start, intermittent stopping, or unresponsive Start caused by broken wires or burned connectors
• Ensures the control receives accurate switch status for safe operation
• Replaces brittle insulation, heat-damaged wiring, or loose terminals that cause poor continuity

• Disconnect power at the breaker before servicing and verify no voltage is present
• Photograph connector locations and wire routing; transfer any clips or retainers
• Seat connectors fully and route wires away from sharp edges and hot surfaces
• After installation, check switch continuity and operation before closing up panels

This control knob replaces a worn or broken range/stove control and restores a secure, easy-to-grip interface for setting burner or oven controls. It provides a direct fit for the original control shaft so you can safely adjust heat settings. What it does

• Replaces a damaged, cracked, or missing control knob so you can turn burners or oven functions.
• Restores a secure fit when original knob is loose or slips on the control shaft.
• Makes temperature and function adjustments easier when the original markings or grip are worn.
• Helps prevent accidental changes by providing proper tactile feedback and alignment.

• One control knob

• Disconnect power to the appliance before removing or installing controls to avoid electrical shock.
• Pull the old knob straight off the control shaft; align the replacement splines and push the new knob on until it seats.
• If the knob is tight to install, do not force—inspect the control shaft and knob splines for damage or debris.
• If ignition or control problems persist after knob replacement, diagnostic service of the switch or control assembly may be required.

This replacement screw secures appliance components and helps keep panels, brackets, and controls firmly attached for reliable operation. It's a simple, direct fix when a mounting screw is missing, loose, or stripped. What it does:

• Fastens panels, trim, brackets or electrical components to reduce movement and rattling.
• Restores proper alignment of parts that shift when a screw is missing or worn.
• Helps maintain electrical and mechanical connections by keeping components seated.
• Common symptom: loose or vibrating panels, trim gaps, or visibly missing hardware.

• Disconnect power to the appliance before accessing internal components.
• Use the correct screwdriver or driver bit to avoid stripping the head.
• Thread gently and avoid overtightening to prevent stripping the mating threads or cracking surrounding parts.
• Keep any removed hardware organized to ensure placement of all required fasteners during reassembly.

This cooktop grate assembly replaces a damaged or missing stove grate to restore a stable surface for pots and pans and ensure even cooking. Designed to sit over the burner area and support cookware during use. What it does:

• Supports cookware over the burner for safe, steady cooking
• Keeps pots and pans level to reduce tipping and spilling
• Restores proper clearance above burners for consistent flame pattern
• Replaces cracked, broken, warped, or missing grates that cause instability

• Allow the cooktop to be completely cool before replacing the grate
• Remove any old grate and set the new grate into position; ensure feet/locating tabs sit flush
• No special tools typically required; follow your appliance manual for model-specific guidance