Jgraham1qcom Parts

This control valve is an important safety feature found on many gas ranges. It's located inside the back of the range near the area where the buttons and controls are found. The reason the control valve is included in ovens is to prevent gas from moving to the burners if the igniter is not able to ignite the gas or there is no electricity. The control valve could be faulty if there is a smell of gas near the valve, the burner flame flickers, or the flame cannot be turned on high.In any of these situations, the control valve must be replaced. The repair is easy and takes only a few minutes. The bottom of the oven will need to be removed, which may require a screwdriver. After removing it, remove the flame spreader by taking out two screws and sliding it out of the oven. Remove the screw holding the oven burner tube and take it out to access the valve and replace it.This control valve is made to be compatible with RCA, Kenmore, Roper, General Electric, and Hotpoint ranges. It's sold as an individual OEM replacement part that is sourced directly from the manufacturer.

Size: 10-24 x 3/8 inch.

Size: 10-32

The Snap Nut is an OEM part for Whirlpool ovens and ranges. It is used to secure various components within the appliance, providing a reliable and easy-to-install fastening solution. The snap nut ensures that parts such as panels and assemblies remain firmly in place during operation.

Causes of a bad snap nut can include wear and tear from regular use, over-tightening during installation, or damage due to impacts or vibrations.

Symptoms of a bad snap nut include:

• Loose or wobbly components within the oven or range
• Parts not staying securely attached
• Unusual noises from vibrating or rattling parts during operation
• Difficulty in assembling or disassembling parts

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This pressure regulator controls incoming water pressure to the appliance's water/ice system, helping maintain steady flow for proper dispenser and ice maker operation. Replaces a worn or failing regulator to restore correct water delivery. What it does:

• Reduces and stabilizes incoming household water pressure for the appliance's water valve/ice maker
• Helps prevent overfilling, leaking, erratic dispenser flow, or poor ice production caused by excessive pressure
• Works with the water inlet system to ensure consistent fill cycles and reliable dispensing
• Compatible with models that use WP74006429 as the factory regulator

• One pressure regulator

• Shut off water supply and unplug the appliance before replacing the regulator
• Inspect fittings and tubing for damage; replace any worn connectors or seals
• Tighten fittings securely and check carefully for leaks after restoring water and power

This igniter switch operates the burner lighter so the cooktop sparks and lights a gas burner when you press the lighter control. Replacing a faulty switch restores consistent ignition and reliable burner starting. What it does:

• Sends the ignition spark to the burner when the lighter/push-button is pressed.
• Replaces a worn, sticky, or unresponsive lighter switch that prevents consistent sparking.
• Common symptoms it can address: no spark from the lighter, intermittent sparking, or a button that fails to activate ignition.
• Interfaces with the existing lighter mechanism and wiring to restore normal ignition function.

• Disconnect power (unplug) and shut off the gas supply before starting any work.
• Access typically requires removing the cooktop or control panel; use appropriate hand tools and keep track of fasteners.
• Avoid touching electrical contacts and confirm wiring matches the original during reassembly.

Size: 26 inches long. F18t8/cw/k26.

A replacement spark module that controls timed ignition sparks to burner electrodes so gas burners light reliably. Restores proper ignition when the cooktop clicks continuously or burners fail to light. What it does:

• Sends high-voltage sparks to the burner ignitors so gas burners ignite
• Stops continuous or rapid clicking when the module is faulty or intermittent
• Helps diagnose ignition issues when used with known-good ignitor electrodes and harnesses
• Works as the electronic control for the cooktop/range ignition system

• Disconnect electrical power and shut off gas supply before beginning service
• Handle the board and connectors carefully to avoid static damage; do not touch exposed contacts
• After installation, test all burners for correct ignition and check for gas leaks before normal use

This drawer glide supports the appliance's drawer and provides a smooth, guided track for opening and closing. Replacing a worn or broken glide restores stable movement, proper alignment, and helps prevent sticking, dragging, or derailing. What it does:

• Provides the sliding interface between the drawer and the cabinet frame
• Keeps the drawer aligned for smooth in-and-out motion
• Reduces friction and noise from a worn or damaged glide
• Common fix for drawers that stick, bind, tilt, or pop off the track

• 1 drawer glide

• Disconnect power to the appliance before servicing
• Remove the drawer to access the glide and note the original orientation
• Release retaining tabs or remove mounting fasteners; transfer any reusable hardware
• Install the new glide, avoid overtightening fasteners, reseat the drawer, and test travel

This door window gasket seals the oven door glass to help contain heat and prevent steam or smoke from escaping. It restores a tight seal to keep cooking temperatures consistent and the kitchen cooler. What it does:

• Forms a heat-resistant seal around the oven door window to reduce heat loss.
• Helps prevent steam, smoke, and odors from leaking into the kitchen.
• Can improve oven temperature stability when the original gasket is worn or damaged.
• Common symptoms: visible gaps, brittle or torn gasket, excessive heat felt near the door edge.

• One door window gasket

• Inspect the door glass and channel for debris before installing; clean the area to ensure a proper seal.
• Installation typically requires removing the oven door or inner glass panel—follow the oven manufacturer's instructions.
• Use heat-resistant gloves and allow the oven to cool completely before attempting service.

Color: Biscuit. Size: 13 oz. can. Enamel spray paint.

This flat washer (.250 inch inner diameter x .812 inch outer diameter) is a simple replacement part that helps distribute load from a fastener and protects mating surfaces for reliable appliance operation. What it does:

• Provides a stable bearing surface for screws, bolts or studs to reduce wear on parts
• Helps distribute clamping force to prevent pull-through or deformation of softer materials
• Reduces vibration and movement at the joint when installed correctly
• Missing or damaged washers can lead to loose fasteners, increased vibration or component misalignment

• Disconnect power and water before servicing the appliance
• Replace like-for-like: inner/outer diameters and thickness match the original washer
• Inspect mating hardware and surfaces for damage; replace corroded or deformed fasteners as needed
• Tighten fasteners evenly and avoid over-torquing to prevent washer or component damage

This white valve knob replaces a worn, cracked or missing control knob so you can safely and easily adjust burner or oven settings. It restores a secure grip and precise control for temperature or flame adjustments. What it does:

• Replaces a damaged or stripped control knob used to turn gas or electric valve controls
• Provides a positive grip so settings can be changed smoothly and accurately
• Helps stop slipping or spinning that prevents proper temperature or flame adjustment
• Matches original fit to engage the control shaft properly when installed

• Turn off power and gas supply before removing the old knob
• Pull off the old knob straight from the control shaft; align splines and push new knob fully onto the shaft
• Do not force or hammer the knob; ensure it seats squarely to avoid damage
• Test control operation after installation and restore power/gas only when connection is secure

This wiring harness connects a control or door switch to the appliance's main wiring, restoring proper electrical connection so the switch can send signals to the control. Fits as a direct replacement when the original harness is damaged or wiring is loose. What it does:

• Provides the electrical connection between a switch and the appliance wiring harness
• Restores switch operation when wires are frayed, broken, or connectors are damaged
• Helps prevent intermittent operation caused by loose or corroded terminals
• Matches OEM connector types and wire routing for correct fit and function

• One replacement switch wiring harness

• Intended for users comfortable with basic appliance repair; disconnect power (unplug or shut off breaker) before starting
• Verify connector orientation and secure all terminals; avoid pinching wires during reassembly
• If wiring insulation is damaged beyond the harness area, replace or repair wiring before use

This spacer secures and maintains proper spacing between adjacent appliance components to prevent rubbing and misalignment, helping restore smooth, stable operation after wear or replacement. What it does:

• Positions and cushions parts to prevent metal-on-metal contact and reduce noise or vibration
• Keeps components aligned for proper fit and function after panel or assembly reinstallation
• Helps maintain clearance for moving parts to avoid abrasion and premature wear
• Useful when replacing worn fasteners, clips, or assemblies that rely on precise spacing

• Disconnect power (unplug or switch off circuit breaker) before beginning any repair
• Handle small parts carefully and retain any associated fasteners; compare new part to old for orientation
• Use basic hand tools as required; avoid forcing parts into place to prevent damage