Jmw2430 Parts

This factory fastener secures components inside your appliance, keeping panels, brackets, and assemblies properly attached. Replacing a worn, stripped, or missing screw restores a tight fit and helps prevent vibration, rattling, and misalignment.

• Fastens parts to frames, panels, or brackets as specified in your model's parts diagram
• Helps maintain alignment and reduce vibration/rattling during operation
• Replace when the original screw is missing, corroded, stripped, or no longer holds
• Direct OEM hardware for the designated locations on applicable models

• Disconnect power; shut off gas/water if applicable. Allow hot surfaces to cool.
• Use the correct driver size; start threads by hand to avoid cross-threading.
• Tighten until snug—do not overtighten, especially into plastic or thin sheet metal.
• If a mating clip, insert, or nut is damaged, replace that hardware per your model diagram.

This electronic control board manages oven functions and user-interface commands so the range heats and responds correctly. Replacing a failed control restores cycle selection, temperature control, and display responsiveness. What it does:

• Receives inputs from the touchpad/controls and runs oven bake, broil and timed functions
• Controls temperature regulation and oven cycling for accurate heating
• Drives the console display and status indicators for user feedback
• Can stop normal operation when it fails, causing blank display, unresponsive controls, or incorrect heating

• Disconnect power at the breaker or unplug the appliance before starting
• Handle the board by its edges and avoid static discharge; ground yourself first
• Access typically requires removing the console/inner panel and disconnecting wire harnesses

This replacement screw fastens appliance panels and small internal components to restore secure mounting and reduce rattling or movement. It's a direct-replacement style fastener used where factory screws have become missing, worn, or damaged. What it does:

• Secures panels, brackets and accessory parts in their original mounting locations.
• Restores proper fit to reduce vibration, rattling or loose covers.
• Replaces stripped, rusted, or missing screws that prevent proper alignment.
• Small, low-profile fastener intended for factory thread and hole sizes.

• Disconnect power and water before starting repairs.
• Use the correct screwdriver or bit to avoid stripping the head.
• Tighten until snug; avoid over-tightening to prevent thread damage.
• Keep small parts away from children and pets during installation.

This temperature sensor monitors oven cavity temperature and sends readings to the range control so your oven can regulate bake and broil cycles more accurately. Replaces a failing sensor to restore reliable temperature sensing. What it does:

• Detects oven cavity temperature and reports it to the control board
• Helps the range maintain set cooking temperatures during bake/broil cycles
• Common symptom: oven runs too hot, too cold, or cooks unevenly
• Can cause temperature-related error codes or prevent proper preheating

• Disconnect power to the appliance before starting any repair
• Handle the sensor and its wiring harness carefully to avoid damage
• Install the sensor in the original location and orientation for proper readings

This jack probe is a small electrical connector that provides a secure signal or power connection between wiring harnesses and appliance components, helping restore reliable circuit contacts and proper function. What it does

• Provides a stable electrical connection between harness leads and a mating component or board
• Restores intermittent or open circuits that can cause component failure or erratic operation
• Commonly linked to symptoms such as intermittent power to a component, failures to start, or fault codes related to open connectors
• Simple replacement cures connection-related faults when the original connector is damaged or corroded

• One jack probe electrical connector

• Always unplug the appliance or disconnect power at the breaker before servicing
• Verify connector orientation and secure seating; improper seating may cause intermittent faults
• Inspect mating pins and surrounding wiring for damage before installing; replace any damaged wiring or terminals

The Outer Door Glass is an OEM replacement part for Whirlpool wall ovens. As the primary viewing window, it allows users to oversee cooking from outside the appliance. 

Symptoms of a faulty oven door glass include:

• Chips, cracks or breaks compromising integrity  
• Discoloration or mineral deposits reducing visibility
• Warping or improper sealing when closed
• Binding issues involving the door hinges and lock 

Causes may relate to impacts sustained over time cracking the pane. Exposure to repeated heat cycling during cooking can also lead to warping. Vibrations from closing and latching exacerbate small issues.

This OEM part is compatible with wall ovens from Maytag, KitchenAid and Jenn-Air brands.

The Noise Filter is an OEM component specifically designed for Whirlpool microwaves. It works to dampen vibrations and reduce noise originating from the microwave's internal mechanisms during use. 

Causes of a bad noise filter include degradation of the noise-dampening material over repeated heating cycles. Microwave usage subjects the filter to heat and vibration stress.

Symptoms of a bad noise filter include:

• Increased volume levels emanating from the microwave cabinet
• Louder high-pitched whining or buzzing sounds  
• Vibrations felt on the exterior of the microwave body

This OEM Whirlpool replacement noise filter helps ensure a quiet cooking experience. Its precise design and durable construction minimize disruptive sounds. Please replace yours if you notice louder than normal operation noise. 

This part is also compatible with some KitchenAid, Jenn-Air, Amana, and select Kenmore and Frigidaire microwaves. 

This flat washer is a direct-replacement fastening washer that restores proper spacing and fastening for appliance panels and components. It helps re-secure loose hardware so assemblies sit and operate as intended. What it does:

• Provides a smooth bearing surface for bolts and screws to distribute load
• Helps keep fasteners tight to prevent wobble or loose panels
• Restores correct spacing and alignment between mating parts
• Can reduce vibration-related noise when worn or missing

• One replacement flat washer

• Disconnect power and water before starting repairs
• Use the correct size socket or driver to remove and reinstall fasteners
• Inspect mating fastener and surrounding parts for wear; replace if damaged
• Tighten hardware securely but avoid overtightening which can deform the washer

This oven temperature sensor monitors the oven cavity temperature and sends readings to the control board so your range can maintain accurate cooking temperatures. Replacing a faulty sensor restores proper temperature sensing for reliable bake and roast results. What it does:

• Measures internal oven temperature and reports it to the control board
• Helps maintain set cooking temperatures for even baking and roasting
• Common repair for ovens that run too hot, too cool, or display temperature errors
• Works with electronic controls to enable accurate temperature cycles

• One temperature sensor

• Disconnect power to the appliance before beginning any repair
• Sensor typically mounts inside the oven cavity and connects to a plug or harness; confirm connector location before removing
• Handle sensor carefully to avoid bending or damaging the probe

Size: 2.8 fl.oz tube. 748 non-corosive sealant.

This meat probe is the oven temperature sensor that monitors internal food temperature to help you cook meat to the desired doneness. It delivers accurate readings to the oven control so timed and probe-based cooking cycles work properly. What it does:

• Senses internal food temperature and sends that reading to the oven control board
• Enables probe-based cooking and automatic shutoff when target temperature is reached
• Helps correct symptoms like probe-based cook cycles not ending or inconsistent doneness
• Replaces a damaged or intermittently-reading probe that prevents reliable temperature detection

• One meat probe/temperature sensor

• Disconnect power to the appliance before accessing the oven interior or wiring
• Allow the oven to cool fully and handle the probe and connector carefully to avoid wire strain
• Inspect the probe connector and socket for corrosion or damage before installing

A small replacement button plug that fills a control-panel or console opening and restores a finished appearance. Keeps panels sealed and prevents debris from entering unused holes. What it does:

• Covers unused control holes or mounting openings on consoles and panels
• Helps block dust, moisture, and grime from entering appliance internals
• Restores a consistent, finished look to the control surface
• Useful when a damaged or missing plug leaves an exposed opening

• One button plug (black)

• Typically snaps into place from the front of the panel; no special tools usually required
• Ensure the cavity is clean and free of debris before installing for a secure fit
• If the plug sits near electrical components, disconnect power to the appliance before servicing
• Verify fit against the opening before final installation; slight trimming is not recommended unless specified

The Oven Door Glass Spacer is an OEM part for Whirlpool ovens. This part helps maintain the structural integrity of the oven door, preventing heat escape, and ensuring the door glass remains securely in place during the oven's operation. 

Causes of a bad Oven Door Glass Spacer can range from wear and tear over time, leading to degradation or loss of the spacer, to improper installation that may cause the spacer to dislodge or fail to provide adequate support. 

Symptoms of a malfunctioning Oven Door Glass Spacer include:

• Loose or rattling oven door glass
• Uneven gaps around the door glass, indicating misalignment
• Heat leaking from around the oven door, potentially affecting cooking performance

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This glass bracket secures the oven door glass to the door assembly, keeping the glass stable during normal use and helping maintain a proper seal. Replaces a worn or broken bracket to restore door stability and alignment. What it does:

• Holds the oven door glass in place so the door opens, closes, and seals correctly
• Prevents rattling, movement, or misalignment of the inner/outer door glass
• Helps maintain even heat containment by keeping the glass properly positioned
• Commonly replaced when the bracket is cracked, bent, or missing hardware

• Basic hand tools required; avoid over-tightening fasteners which can crack the glass
• Disconnect power to the appliance before removing or servicing the door
• Support the door and glass during removal to prevent dropping or breakage

This convection fan motor assembly circulates air inside the microwave's convection oven cavity to promote even cooking and browning. It replaces a failed fan motor to restore proper airflow for convection cooking performance. What it does:

• Circulates heated air across the oven cavity for more even baking and roasting
• Aids in consistent temperature distribution during convection cycles
• Stops or reduces overheating by moving hot air away from internal components
• Common symptoms: no convection airflow, uneven cooking/browning, humming or grinding noise from fan area

• Disconnect power at the breaker or unplug the appliance before servicing
• Handle sharp sheet-metal edges and the assembly carefully to avoid cuts
• Verify connector orientation and secure wiring; do not force connectors