Jmw2430 Parts

The Door Hinge Receiver is an OEM part for Whirlpool ranges. It receives and pivotally mounts the range door hinges, facilitating smooth opening and closing of the door.

Causes of a bad range door hinge receiver include normal wear and tear over time, repeated opening and closing stress, and damage or warping from excessive heat exposure.

Symptoms of a bad door hinge receiver include:

• Cracks or wear on mounting surfaces that could compromise safety
• A loose, wobbly or misaligned range door that does not seal properly
• The door being difficult to open and close smoothly
• Potential for the door to fall off if mounting surfaces fail

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
 

This power supply is the electronic control board that provides the regulated voltages and control signals needed for the appliance's user console and main controls to operate reliably. It restores proper power distribution so controls can respond. What it does:

• Converts incoming AC to the low-voltage DC used by the console and control circuitry.
• Powers display, buttons, and control relays so the appliance can receive and execute commands.
• Common symptom: blank or unresponsive display/console.
• Common symptom: intermittent or total loss of control functions, or failure to start cycles.

• Disconnect power before servicing to avoid electrical shock.
• Handle the board by its edges and avoid ESD (static) damage—use proper grounding.
• Reassemble panels and secure connectors fully; test control functions after installation.

Seals the appliance door to prevent leaks and keep the interior working as intended. Replace a cracked, torn, or hardened gasket to stop leaks, reduce odor and mold, and restore a reliable door seal. What it does:

• Forms a tight seal between the door and cabinet to prevent water, air, or heat loss
• Stops common symptoms like visible cracks or gaps, water pooling, and persistent odors
• Restores proper containment for cleaning, heating, or washing cycles
• Matches the OEM channel/retainer design for a secure fit

• Disconnect power and water before beginning any repair
• Remove the old gasket, thoroughly clean the mounting area, then seat the new gasket into the door channel or retainer
• Work the gasket evenly around the door; avoid overstretching and ensure all beads/clips are fully engaged

The Door Glass is an OEM part for Whirlpool ranges. It forms the inner layer of the oven door, providing insulation and protection against high temperatures during cooking. The oven door inner glass ensures heat is contained within the oven cavity, allowing for efficient and even cooking. It also acts as a barrier, preventing any spills or debris from entering the space between the inner and outer glass layers.

A bad oven door inner glass can occur due to accidental impact, extreme temperature changes, or regular wear and tear. If you notice symptoms such as cracks, shattered glass, or compromised insulation, it may be time to replace this part.

Symptoms of a bad oven door inner glass include:

• Cracks or shattered glass
• Compromised insulation
• Difficulty in maintaining consistent cooking temperatures

Restore your Whirlpool range by replacing the damaged or worn oven door inner glass with this genuine OEM part.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

This tension spring restores proper movement and tension for the appliance component it secures, helping the part operate smoothly and reliably. It's a simple replacement that fixes common issues caused by worn or broken springs. What it does:

• Provides tension to hold or return a moving component to its correct position
• Helps stop sagging, slipping, or loose operation of doors, latches, or levers
• Can reduce rattling or unusual noises caused by a failed spring
• Restores normal mechanical action when the original spring is stretched or broken

• Disconnect power to the appliance before starting any repair
• Springs can be under tension—use appropriate tools and wear eye/hand protection
• Compare the new spring to the old one for length, coil size, and end fittings before installation

The Speaker is an OEM component specifically designed for Whirlpool brand washers. It alerts users with chime tones or voice prompts during cycle operation or any error states. Precise acoustic engineering allows for clear audio reception even amid operating vibrations. 

Symptoms of a bad speaker include: 

• No audio tones or voice prompts were heard  
• Muffled, distorted, or unusually loud sounds
• Speaker making rattling or buzzing noises

Causes can be damage from water damage, defects in the audio circuitry, or aging components. 

This speaker ensures optimal user communication. Without it, you cannot verify cycle progress or troubleshoot issues. Its dependable performance maintains the washer's convenience.

This Whirlpool OEM part fits perfectly while extending the equipment's lifespan. It is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This small bumper cushions contact points inside your appliance to prevent metal-to-metal contact. It helps reduce noise, protect finishes, and keep moving parts stopping smoothly and aligning as designed.

• Absorbs impact so doors, drawers, or racks stop quietly instead of slamming
• Protects painted/enamel surfaces from chips, scratches, and premature wear
• Helps maintain proper spacing and alignment where specified by the manufacturer
• Replace if missing, cracked, flattened, or if new rattling/clunking noises appear

• Disconnect power; turn off water supply if applicable
• Allow any hot surfaces to cool before starting
• Gently remove the old bumper; clean the mounting area
• Press-fit or seat the new bumper fully; installation method can vary by model—follow your service documentation

This microwave door outer assembly replaces a damaged or broken door to restore the appliance's appearance and proper closure. It helps maintain the microwave cavity seal and allows the door latch and handle to function correctly. What it does:

• Replaces a cracked, dented, or cosmetically damaged outer door panel
• Restores proper door closure and engagement with the latch for safe operation
• Helps reduce light, steam, and food vapor escaping the cavity during use
• Improves the microwave's finished appearance and user access

• Disconnect power at the breaker or unplug the microwave before servicing
• Handle and latch components may be attached; verify correct alignment during reassembly
• Use appropriate tools and avoid forcing plastic clips to prevent damage

This is a replacement 8-18 screw used to secure components in compatible Whirlpool appliances. It provides a reliable, corrosion-resistant fastener to restore proper fit and function for panels and internal parts. What it does:

• Secures panels, brackets, or small internal components where an 8-18 thread is specified
• Restores loose or missing fasteners that cause rattling, misalignment, or improper sealing
• Matches OEM thread size and head profile for a correct fit when listed for your model
• Prevents further wear or damage caused by using the wrong screw size

• One screw as shown

• Turn off and unplug the appliance before starting any repair
• Use the proper screwdriver or driver bit to avoid stripping the head
• Do not overtighten—tighten until snug and components seat without play
• Replace only where the OEM specifies an 8-18 screw to ensure proper fit

This replacement door glass is the exterior glass panel that restores the look and function of the appliance door, providing a clear viewing surface and protecting the internal door components. Ideal for cracked, chipped, or scratched glass. What it does:

• Replaces a damaged or broken door glass panel to restore a clear viewing surface
• Protects internal door components from moisture and debris
• Helps maintain the appliance's sealed closure and appearance
• Common symptom: visible cracks, chips, or shattered glass on the door

• One door glass panel

• Handle glass carefully and wear cut-resistant gloves and eye protection
• Follow the appliance manufacturer's disassembly instructions; door removal may be required
• Inspect and reuse or replace any related clips, gaskets, or trim as needed

This spacer provides a small, rigid gap between appliance components to maintain proper alignment and prevent contact. It restores correct spacing so panels, doors, or assemblies fit and move as intended. What it does:

• Maintains proper clearance between parts to prevent rubbing, binding, or wear
• Helps align panels, trim, or assemblies for smooth operation
• Supports fasteners or clips to ensure a secure fit
• Can reduce vibration-related noise when spacing is correct

• One spacer

• Disconnect power or gas before servicing the appliance
• Inspect mounting area and fasteners; replace any worn clips or screws as needed
• Install in the original orientation; do not force into place or over-tighten fasteners

This support is a replacement mounting bracket that stabilizes and secures internal components to prevent movement and wear. It restores proper alignment and reduces vibration and noise caused by a damaged or missing support. What it does

• Provides structural support for internal appliance assemblies to keep parts aligned.
• Reduces vibration and rattling that can occur when a support is cracked or broken.
• Prevents sagging or shifting of panels and components that may lead to further wear.
• Helps maintain normal operation by keeping moving parts properly positioned.

• Disconnect power (and water if applicable) before beginning any repair.
• Remove any panels or components blocking access.
• Verify bracket orientation and mounting hole alignment before tightening fasteners.
• Use appropriate hand tools and avoid overtightening to prevent damage; replace any fasteners that are worn or damaged.

The Nameplate is an OEM part for Whirlpool ranges. Located on the front of the appliance, the nameplate serves an important branding and identification purpose. 

Causes of a bad nameplate may include damage from harsh or abrasive cleaners, long-term wear from heat and steam exposure in the kitchen, or accidental impact. 

Symptoms of a bad nameplate include:

• Fading or corrosion of printed information
• Loss of adhesive attachment to appliance front 
• Cracks or breaks in the plastic material
• Missing or illegible model/serial numbers

This authentic Whirlpool replacement nameplate restores the professional appearance expected of the brand. It ensures proper identification for future service needs as well. This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge and Kenmore range models.

The Screw is an OEM part for Whirlpool microwaves. It is a small yet vital component that joins together other parts of the microwave to create a cohesive machine. The screw is responsible for tightly securing internal components like the magnetron tube, control panel, and outer case during operation.  

Symptoms of a bad screw include:

• Loose or detached internal microwave components 
• External parts like the door or casing that will not stay aligned or attached
• Overheating or arcing due to poor grounding from loose screws
• Component malfunctions if mounting positions are compromised

Causes of a bad screw can include wear and tear that causes stripping or loosening over time, or damage from handling that results in breaking or bending.  

This OEM Whirlpool part is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore microwave models.

A 6-32 machine screw used to secure panels, brackets, and components in many Whirlpool appliances. Replaces worn or missing fasteners to restore proper fit and stop loose parts from rattling or shifting. What it does:

• Secures panels, trim, brackets, and small assemblies
• Helps stop vibration and rattling caused by loose fasteners
• Restores proper alignment for parts held by a 6-32 thread
• Prevents further wear from movement or improper fit

• Disconnect power to the appliance before beginning any repair
• Use the correct driver for the screw head to avoid stripping
• Thread gently and avoid overtightening to prevent damage to threads or components
• Keep removed fasteners organized to ensure correct reassembly