Kebs179bssoo Parts

This meat probe jack is the oven-side connector that accepts the temperature probe to monitor food internal temperature and control cooking. It restores the electrical connection between the probe and the oven control for accurate probe readings. What it does:

• Provides the socket where the temperature/meat probe plugs into the oven control circuit
• Enables the oven to read probe temperature for probe-cooking modes and doneness alerts
• Commonly replaces a jack that is worn, loose, cracked, or not registering probe temperature
• Helps resolve symptoms like probe not detected, intermittent probe readings, or probe error messages

• Disconnect power to the appliance before attempting repair to avoid electrical shock.
• Replacement typically requires access behind the control panel or console; handle display and control components carefully.
• Keep track of mounting hardware and connector orientation; confirm probe detection before reassembling fully.

This mounting bracket is a replacement support bracket that secures appliance components and keeps assemblies aligned for reliable operation. It restores proper fit and helps prevent rattling or movement from loose fittings. What it does:

• Secures panels or assemblies to the appliance frame to maintain proper alignment
• Reduces vibration and rattling caused by loose or damaged supports
• Restores mounting points that prevent sagging or separation of connected parts
• Helps ensure stable operation after repairs involving removed or replaced hardware

• Follow the appliance service manual for exact location and fastener torque
• Disconnect power (and gas if applicable) before beginning any repair
• Use appropriate tools and replace any damaged screws or clips with OEM-equivalent fasteners

The Door Hinge Receiver is an OEM part for Whirlpool ranges. It receives and pivotally mounts the range door hinges, facilitating smooth opening and closing of the door.

Causes of a bad range door hinge receiver include normal wear and tear over time, repeated opening and closing stress, and damage or warping from excessive heat exposure.

Symptoms of a bad door hinge receiver include:

• Cracks or wear on mounting surfaces that could compromise safety
• A loose, wobbly or misaligned range door that does not seal properly
• The door being difficult to open and close smoothly
• Potential for the door to fall off if mounting surfaces fail

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
 

This small bumper cushions contact points inside your appliance to prevent metal-to-metal contact. It helps reduce noise, protect finishes, and keep moving parts stopping smoothly and aligning as designed.

• Absorbs impact so doors, drawers, or racks stop quietly instead of slamming
• Protects painted/enamel surfaces from chips, scratches, and premature wear
• Helps maintain proper spacing and alignment where specified by the manufacturer
• Replace if missing, cracked, flattened, or if new rattling/clunking noises appear

• Disconnect power; turn off water supply if applicable
• Allow any hot surfaces to cool before starting
• Gently remove the old bumper; clean the mounting area
• Press-fit or seat the new bumper fully; installation method can vary by model—follow your service documentation

This is a replacement 8-18 screw used to secure components in compatible Whirlpool appliances. It provides a reliable, corrosion-resistant fastener to restore proper fit and function for panels and internal parts. What it does:

• Secures panels, brackets, or small internal components where an 8-18 thread is specified
• Restores loose or missing fasteners that cause rattling, misalignment, or improper sealing
• Matches OEM thread size and head profile for a correct fit when listed for your model
• Prevents further wear or damage caused by using the wrong screw size

• One screw as shown

• Turn off and unplug the appliance before starting any repair
• Use the proper screwdriver or driver bit to avoid stripping the head
• Do not overtighten—tighten until snug and components seat without play
• Replace only where the OEM specifies an 8-18 screw to ensure proper fit

A 6-32 machine screw used to secure panels, brackets, and components in many Whirlpool appliances. Replaces worn or missing fasteners to restore proper fit and stop loose parts from rattling or shifting. What it does:

• Secures panels, trim, brackets, and small assemblies
• Helps stop vibration and rattling caused by loose fasteners
• Restores proper alignment for parts held by a 6-32 thread
• Prevents further wear from movement or improper fit

• Disconnect power to the appliance before beginning any repair
• Use the correct driver for the screw head to avoid stripping
• Thread gently and avoid overtightening to prevent damage to threads or components
• Keep removed fasteners organized to ensure correct reassembly

This wire harness provides the factory-style electrical connections needed to restore secure, organized wiring in your appliance. Replacing a damaged harness helps re-establish reliable power and signal paths for controls and components. What it does:

• Connects multiple internal components with pre-terminated wiring and color-coded connectors
• Ensures correct signal and power routing between control boards, switches, and motors
• Commonly used to address intermittent power, loss of functions, or components that don't respond
• Keeps wiring bundled and secured to prevent chafing or short circuits

• Disconnect power (unplug or switch off breaker) before starting any repair
• Match connector shapes and wire colors; route and secure harness along the original path
• Inspect connectors and insulation; replace the entire harness if any wire or terminal is damaged