Kebs207sss Parts

This wire cover is a protective sleeve that helps route and shield appliance wiring to reduce wear and prevent accidental contact. It restores a neater harness run and helps maintain safe electrical routing inside the appliance. What it does:

• Protects wires from abrasion and chafing against sharp edges or moving parts
• Helps prevent exposed conductors that can cause shorts, arcing, or burning smells
• Keeps wiring bundled and routed to reduce pinching and stress on connectors
• Reduces risk of intermittent electrical issues caused by damaged insulation

• Disconnect power before beginning any service to avoid shock or injury
• Inspect surrounding wiring and connectors for damage; replace any frayed or exposed wires
• Slide cover over the wiring harness or route harness through sleeve as needed; secure with existing clips or approved fasteners

This 6mm acorn nut secures exposed threaded studs and protects threads while giving a finished appearance. It's a simple replacement fastener that restores proper fit and helps prevent snagging or corrosion on accessible assemblies. What it does:

• Caps and secures exposed studs or bolts to keep assemblies fastened
• Protects threads from damage, dirt, and moisture
• Restores a finished look to trim, panels, or hardware mounts
• Can stop rattling or looseness when a worn/ missing nut is the cause

• One 6mm acorn nut

• Use the correct 6mm socket or nut driver; tighten until snug—avoid overtightening
• Disconnect power and follow appliance safety procedures before working near electrical or moving components
• Inspect mating threads for damage and replace the mating fastener if stripped

Splicing 25 Ft. Black 12 Ga. 150~c (Wire, Red 14 Ga. 200~c)

This door glass is the clear panel in the appliance door that restores visibility and door integrity when the original glass is cracked, shattered, or damaged. Replacing it restores a safe, clean viewing window.

• Replaces a broken or cloudy door glass panel to restore a clear view into the interior
• Helps maintain proper door integrity and safe operation after damage
• Common symptoms: cracks, chips, spiderwebbing, shattered glass, or loose/rattling fragments
• Cosmetic damage inside the window area that cannot be cleaned away

What's included: One door glass panel Install notes:

• Disconnect power; for gas units shut off gas, and for water-using appliances shut off water before service
• Wear cut-resistant gloves and eye protection; handle glass by the edges only
• Support or remove the door per service instructions; transfer original trim, brackets, and screws to the new glass
• After reassembly, verify door alignment, latch operation, and seal

This is a control board that fits various ovens, ranges, and stoves. This is an internal component that is responsible for the relays that control the burners or elements inside the oven. If the oven isn't heating or is unevenly cooking items, it could be an issue with the control board. Make sure to test the heating elements to ensure they are receiving power. If they are, the control board likely needs to be replaced.Before replacing this part, make sure to have a screwdriver, wrench or nut drive, and putty knife for the process. Unplug the range and turn off the gas, if applicable. Pull the range away from the wall before removing the back shield over the control panel. Next, take a photo of the location of the wires on the control board. Disconnect the wires and remove the control board. Reinstall the wires on the new board and put it in place before reassembling the other parts.The control board is designed to be compatible with KitchenAid wall ovens, stoves, and ranges. It is a genuine OEM replacement part that is sold on an individual basis. This component is directly sourced from the manufacturer.

This is a Whirlpool user interface control board for wall ovens. It features a digital display, allowing the user to set timers and select temperatures for the oven. If this control board has shorted out, the oven may not respond to user input.Before installing this part, be sure to cut power to the appliance and allow it to cool completely. The oven's control panel will need to be removed to access the old component. Disconnect any wire harnesses connected to the old control board and remove any screws mounting it in place before installing the new part.This is a genuine OEM part compatible with ranges manufactured by Whirlpool brands, including Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and others. This product contains no additional parts or hardware.