Kenmore 11021302013 Parts

This main wire harness routes power and signals between the appliance control and internal components to restore proper electrical connections and operation. It's a direct-fit replacement when the original harness is damaged. What it does:

• Connects control board, motors, switches and sensors so circuits receive power and communicate correctly
• Replaces frayed, broken, or corroded wiring that can cause intermittent operation or component failure
• Helps stop issues like no power to controls, intermittent runs, or unexpected shutdowns when caused by damaged wiring
• Maintains factory routing and connector types for reliable electrical connections

• One main wire harness

• Disconnect power (unplug or shut off breaker) before inspecting or replacing the harness
• Compare harness and connectors to the original and route wires following factory paths to prevent chafing
• Secure connectors fully until they click; avoid stretching wires when reinstalling

This wire harness routes power and signals to lower VMW components, restoring proper electrical connection and reliable operation for affected circuits. It replaces a damaged or worn lower harness assembly to help eliminate intermittent power or control issues. What it does:

• Carries electrical power and control signals between lower VMW components and the main wiring system
• Re-establishes secure plug-and-play connections when wires are frayed, broken, or connectors are loose
• Addresses symptoms such as intermittent operation, no power to lower components, or control malfunctions
• Prevents shorts and poor contacts caused by damaged insulation or broken terminals

• Disconnect power before starting any repair to avoid shock or injury
• Handle connectors by the housings; do not pull on wires when removing or installing
• Route and secure the harness following the appliance wiring path and any retaining clips to prevent chafing
• Verify all connectors are fully seated and inspect for pin damage before reapplying power

This cabinet is the main outer housing that supports and protects the appliance's internal components while giving the unit its finished exterior. It restores structural integrity and proper panel alignment for safe, reliable operation. What it does:

• Provides the structural frame and mounting surface for controls, panels, and internal components
• Protects internal parts from dust, moisture, and incidental contact
• Helps maintain proper airflow and component positioning to reduce vibration and noise
• Restores correct panel alignment and closure when the original cabinet is dented, cracked, or corroded

• One cabinet

• Disconnect power (and gas, if applicable) before beginning any repair
• Installing may require removing trim, controls, and internal components; keep fasteners organized
• Use proper lifting technique and a second person for heavy or bulky cabinets to avoid damage or injury

The Lid is an OEM replacement part for Whirlpool washing machines. It is the top cover of the washer that provides access to the interior drum and tub, allowing you to load and unload laundry. The lid is designed to be durable and secure, ensuring safe and proper operation of the washing machine.

Symptoms of a bad Lid include:

• Difficulty opening or closing the lid
• Lid not closing or latching properly
• Visible cracks or damage to the lid material
• Lid becoming detached or falling off

Causes of a bad lid can range from physical damage due to impact or mishandling, to wear and tear over time from repeated use. Exposure to excessive moisture or humidity can also contribute to the degradation of the lid material or mounting mechanisms.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washing machine models. 

This factory screw secures appliance panels and components, keeping them properly aligned and quiet during operation. Replace a stripped, corroded, or missing fastener to restore a snug fit and dependable performance in the original mounting location. What it does:

• Fastens brackets, panels, trim, or internal hardware to the cabinet/frame as specified by the manufacturer
• Helps maintain proper alignment and reduce rattling or vibration when a screw is worn or missing
• Direct replacement for damaged, stripped, or rusted hardware
• Used in various locations per the service diagram; match to the original position

• 1 screw

• Disconnect power (and shut off water or gas, if applicable) before servicing.
• Compare length and thread style to the original; install in the same location.
• Start threads by hand to avoid cross-threading; tighten until snug—do not overtighten.
• Reinstall any brackets or panels in the correct order.

This clamp secures a washer or dryer hose to its connection to prevent leaks and keep the hose firmly in place during operation. It replaces worn or loose clamps that allow water to escape or hoses to detach. What it does:

• Holds a washer/dryer hose to a nipple, collar or fitting to maintain a sealed connection
• Prevents water leaks caused by loose or corroded clamps
• Stops hoses from slipping off during drain or fill cycles
• Restores proper hose retention and reduces risk of water damage

• Disconnect power and turn off the water supply before starting any repair
• Inspect hose and fitting for damage; replace hose if cracked or frayed
• Use appropriate pliers or a screwdriver for the clamp style; avoid overtightening to prevent hose damage
• Verify a leak-free connection after restoring power and water

This rubber pad cushions and protects appliance components from vibration and abrasion, reducing noise and wear. It's a small replacement part that restores proper contact and dampening where original pads have worn or fallen off. What it does

• Cushions panels or components to reduce vibration and rattling
• Prevents direct metal-to-metal contact that can cause scratching or wear
• Helps stabilize parts that have shifted due to a missing or damaged pad
• Commonly replaced when noisy operation or visible pad deterioration occurs

• One replacement pad

• Disconnect power before accessing interior panels or components
• Remove any retaining clips or panels that block the pad's location; pad typically presses into place
• Verify orientation and seating against the mating surface; replace any worn fasteners or retainers
• If adhesive was used on the original, use an OEM-recommended adhesive only.

Note: Bearings are only available with the gearcase assembly.

This is a Whirlpool washing machine basket. The washing machine basket holds laundry during a wash cycle. The basket may become damaged over time due to normal wear and tear, which can be exacerbated by overloading laundry or using the wrong amount of detergent. When the basket starts to become damaged or malfunction, noticeable noise increases may take place during use. Eventually, the damage will lead to the basket failing to spin. The old basket can be removed by first removing the top portion by pushing the fastening clips that hold it in place. After removing the top, reach down to remove the softener cup. Using a socket, unfasten the agitator at the bottom of the basket. After removing the agitator, the basket should easily lift out of the machine.This part is a genuine OEM product and is sourced directly from the manufacturer. It is intended for use in Whirlpool, Maytag, Kenmore, and Crosley appliances.

Kit contains two 10 feet inlet hoses.

Color: White. Size: 1 qt. can. Acrylic appliance paint.