Kenmore 11028132410 Parts

Kit contains two 10 feet inlet hoses.

A U-bend retainer designed to secure a U-shaped heating element or tubing in place, preventing movement and vibration for reliable operation. Fits as the replacement hold-down clip used on compatible Whirlpool HVAC and appliance assemblies. What it does:

• Secures U-shaped element or tubing to the appliance frame or mounting bracket
• Prevents rubbing or vibration that can lead to wear or noisy operation
• Helps maintain proper spacing and alignment of the element for consistent performance
• Used where a compact, U-shaped clamp is required to hold components safely

• One U-bend retainer clip as shown

• Inspect the surrounding area and replaced part for damage before installing
• Use basic hand tools; align clip over the U-bend and fasten to the designated mounting point
• Disconnect power and allow components to cool before attempting repair
• Replace with the exact OEM fasteners

This siphon break kit prevents wastewater from siphoning back into the dishwasher, helping keep the tub and dishes clean and reducing drainback issues. Fits the dishwasher drain assembly to restore proper draining function. What it does:

• Stops backflow by breaking the siphon effect in the drain line
• Works with the dishwasher drain hose and pump to maintain one-way drainage
• Helps address symptoms like water remaining in the tub, partial drains, or water backing into the tub
• Supports proper drainage to reduce odors caused by standing water

• One siphon break kit

• Disconnect power to the appliance and turn off the water supply before starting
• Inspect the drain hose routing and secure the siphon break at the recommended height per the dishwasher's service instructions
• Use basic hand tools; hose clamps or fasteners may be required

This replacement brace reinforces appliance cabinet structure to restore proper alignment and reduce vibration. It helps maintain secure mounting of adjacent panels so doors and controls operate smoothly. What it does:

• Provides structural support for the appliance cabinet and connected panels
• Reduces rattling or vibration caused by loose or bent cabinet components
• Helps realign panels that are pulling away or not closing flush
• Useful when visible damage, bending, or missing support causes fitment issues

• Disconnect power and, if applicable, gas supply before starting any repair
• Remove outer cabinet panels or access panels to reach the brace mounting points
• Retain original fasteners when possible; replace damaged screws or clips as needed

The Switch Mounting Screw is an OEM part compatible with Whirlpool washing machines. This screw securely mounts the cycle selector switch within the control console assembly. Proper fastening ensures dependable operation of control functions.  

Causes of a bad mounting screw can stem from stress cracks developing over multiple years of operation. Vibrations accumulate, slowly loosening connections housed in a wet environment.

Symptoms of a bad mounting screw include:

• Loose or rattling switch within the console face  
• Difficulty selecting cycles as buttons wobble out of place
• Water intrusion hastening corrosion of electrical terminals
• Potential shock hazards if live connections are exposed

This Whirlpool replacement screw restores a tight mounting point. It is compatible with brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Rear Panel is an OEM part compatible with Whirlpool washing machines. As the rear housing component, it protects internal mechanisms from debris while providing structure and stability to the cabinet. Its rigid design assists with even weight distribution to minimize vibrations. 

Symptoms of a bad rear panel can include:

• Warping or flexing of the panel material over time
• Cracks developing from pressure changes in the tub area
• Dents compromising the panel's integrity from heavy loads 

Causes of a bad rear panel washer stem from long-term use, with stress and strain accumulating from years of use. Agitator movement and unbalanced loads can warp the panel out of shape.

This OEM Whirlpool replacement rear panel helps restore the washer's protective barrier. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This wire shield is a molded protective cover that helps keep wiring routed and protected from heat, abrasion and moving parts. It prevents chafing and reduces the risk of shorts for a safer appliance operation. What it does:

• Covers and routes wiring to protect insulation from heat and friction
• Prevents wires from contacting sharp edges or moving components
• Helps stop intermittent shorts, arcing, or wiring damage that can cause odor or failures
• Maintains proper wire position to support consistent electrical connections

• One wire shield

• Disconnect power to the appliance before beginning any work
• Secure with existing clips or fasteners; do not force or modify the part
• If wiring insulation is melted or damaged, replace wiring/harness before reassembly

This brace is a replacement mounting bracket that helps secure internal components and cabinet panels so moving parts stay aligned and your appliance operates more quietly and reliably. Simple, direct fit for service repairs. What it does

• Stabilizes and holds panels or assemblies in place to reduce vibration and movement
• Restores proper alignment of connected components for smoother operation
• Helps stop rattling or shifting that can cause noise during use
• Used when a bent, broken, or missing bracket is causing loose parts

• One brace

• Disconnect power (and water if applicable) before servicing the appliance.
• Remove the access panel or cabinet section needed to reach the damaged bracket.
• Replace the bracket using the original mounting screws and hardware; tighten securely but avoid overtightening.

The Dispenser Drawer is an OEM part for Whirlpool washing machines. It provides storage for pre-treating stains and housing detergent/softener dispensed during cycles. 

Causes of a bad dispenser drawer can include excess vibration/movement causing mechanical failures over time, leakage of water/chemicals corroding components, or impacts weakening structural integrity.

Symptoms of a bad dispenser drawer include:

• Loose, wobbly movement when opening and closing
• Cracks or splits along the frame or surface of the drawer  
• Unable to fully open or close securely
• Detached from the mounting rail or guide tracks

This OEM replacement part is compatible with select Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washer models as well.

This bearing supports a rotating component inside the appliance so it turns smoothly with minimal friction. Replacing a worn bearing helps quiet operation, improves alignment, and prevents premature wear of related parts. What it does:

• Provides a low-friction surface for a shaft or hub to rotate smoothly
• Helps maintain alignment to reduce wobble and uneven wear
• Contributes to quieter, more reliable operation
• Common signs of failure: grinding or squealing noises, rough/stiff rotation, noticeable play/wobble, or visible wear/damage on the old bearing

• 1 bearing

• Disconnect power to the appliance before servicing
• Access the bearing location and remove any retaining screws, clips, or fasteners; note the original orientation
• Clean mating surfaces; transfer any spacers/washers from the old part if present, and seat the new bearing fully
• Spin-test the component by hand to ensure smooth, wobble-free movement before reassembly and test

The Sound Shield is an OEM replacement part for Whirlpool washers. It is a sheet metal panel installed behind the tub that helps reduce noise and vibration during spin cycles. With absorptive insulation, the sound shield dampens noise produced internally. 

Symptoms of a damaged sound shield include:

• Excessively loud operation, especially during high-speed spins
• Rattles, clanks, or resonant noises from inside the washer  
• Potentially weakened structure allowing tub movement
• Causes of a damaged sound shield can include tears or dents sustained over many high-speed spin cycles. Constant vibration may cause stress cracks or loose rivets.

 It is also compatible with some  Whirlpool, Maytag, Amana, and Kenmore brands.

The Speaker is an OEM component specifically designed for Whirlpool brand washers. It alerts users with chime tones or voice prompts during cycle operation or any error states. Precise acoustic engineering allows for clear audio reception even amid operating vibrations. 

Symptoms of a bad speaker include: 

• No audio tones or voice prompts were heard  
• Muffled, distorted, or unusually loud sounds
• Speaker making rattling or buzzing noises

Causes can be damage from water damage, defects in the audio circuitry, or aging components. 

This speaker ensures optimal user communication. Without it, you cannot verify cycle progress or troubleshoot issues. Its dependable performance maintains the washer's convenience.

This Whirlpool OEM part fits perfectly while extending the equipment's lifespan. It is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This clamp secures a washer or dryer hose to its connection to prevent leaks and keep the hose firmly in place during operation. It replaces worn or loose clamps that allow water to escape or hoses to detach. What it does:

• Holds a washer/dryer hose to a nipple, collar or fitting to maintain a sealed connection
• Prevents water leaks caused by loose or corroded clamps
• Stops hoses from slipping off during drain or fill cycles
• Restores proper hose retention and reduces risk of water damage

• Disconnect power and turn off the water supply before starting any repair
• Inspect hose and fitting for damage; replace hose if cracked or frayed
• Use appropriate pliers or a screwdriver for the clamp style; avoid overtightening to prevent hose damage
• Verify a leak-free connection after restoring power and water

This is a replacement bezel — the trim piece that surrounds and protects the appliance control panel, restoring a clean appearance and helping keep buttons and displays shielded from spills and wear. Ideal when the original trim is cracked or cosmetic. What it does

• Covers and protects the control panel area from spills, dust and everyday wear
• Restores a finished look when the original bezel is scratched, faded or broken
• Helps keep control buttons and display edges aligned and accessible
• Fits at the front of the control console and works with existing buttons and switches

• One bezel as pictured

• High-level: typically snaps or screws into the control console — follow your appliance's service manual for removal and reassembly
• Disconnect power before starting work to avoid shock or accidental machine start
• Handle plastic trim carefully to avoid additional cracking; use appropriate screwdrivers or trim tools
• If other control components are damaged, inspect those parts before reassembly