Kenmore 25370343419 Parts

This is a refrigerator door gasket that restores a tight seal to maintain proper cooling and help reduce frost and energy loss. Replacing a worn gasket improves temperature stability and keeps food fresher longer. What it does:

• Seals the refrigerator door to prevent warm air and moisture from entering the fresh-food compartment.
• Helps stop frost buildup and water pooling caused by a failing seal.
• Can reduce excessive run time from the compressor associated with air leaks.
• Common symptom: visible gaps, brittle or torn rubber, or a door that no longer seals evenly.

• One refrigerator door gasket.

• Remove stored food and shelves as needed for safe access before starting.
• Clean and dry the mounting surface thoroughly before installing the new gasket.
• Seat the gasket evenly around the door frame and check the door closing and seal.

This wiring harness routes power and signals between the appliance control and internal components, restoring reliable electrical connections for normal operation. It replaces a damaged or worn harness to help resolve intermittent power and control issues. What it does:

• Provides secure electrical connections between the control board and components
• Restores circuit continuity when a frayed or broken wire causes intermittent function
• Helps eliminate symptoms such as no power to affected components, control errors, or components that won't start
• Maintains OEM routing and connector fit for correct installation and operation

• One complete wiring harness assembly exactly as shown

• Disconnect power to the appliance before beginning work to avoid shock or damage
• Handle connectors by the housings; avoid pulling on individual wires
• Route harness following original cable paths and secure with clips; verify connector seating

This evaporator block is the refrigerator evaporator coil assembly that removes heat from the freezer/refrigerator compartment to help maintain proper cooling and reduce frost buildup. What it does:

• Circulates refrigerant through the evaporator to absorb heat from the compartment
• Promotes cold airflow across the freezer and fresh-food sections when paired with the evaporator fan
• Helps control frost and ice buildup on the evaporator surface
• Common symptoms: reduced cooling, excessive frost or ice buildup, or warm freezer temperatures

• Always disconnect power to the appliance before servicing
• Replacing the evaporator typically requires accessing sealed refrigerant areas;
• Allow components to fully defrost and drain before removal to avoid water damage
• Handle the coil gently to avoid bending fins or damaging tubing

This cover is a replacement trim piece that restores the appliance's appearance and protects internal components from dust and debris. It fits into the appliance's exterior to keep controls and openings concealed and neat. What it does

• Covers and protects exposed openings or components to help prevent dirt buildup and accidental contact.
• Restores a finished, factory appearance where the original cover was cracked, warped, or missing.
• Helps maintain proper airflow and component alignment when installed as intended.
• Reduces the chance of small objects entering internal compartments.

• One replacement cover trim piece as shown.

• Disconnect power to the appliance before removing panels or replacing parts to reduce risk of shock.
• Remove only the fasteners or clips securing the damaged cover; save hardware if the replacement does not include new fasteners.
• Handle the cover carefully to avoid scratching or damaging finish during installation.

This molded plastic air deflector directs cold airflow inside the refrigerator/freezer to help maintain even temperatures and proper compartment circulation. It replaces broken or missing airflow guides to restore proper venting. What it does:

• Guides and directs cold air from the evaporator into the refrigerator/freezer compartments
• Helps reduce hot spots and uneven cooling when functioning correctly
• Commonly replaced if cracked, warped, or broken mounting tabs block airflow
• Can resolve symptoms like inconsistent temperatures, poor cooling in one compartment, or visible airflow leaks

• One air deflector

• Unplug the appliance before beginning any repair to avoid shock or injury
• Remove shelves or drawers as needed to access the deflector; handle plastic tabs gently to avoid breakage
• Install by aligning mounting tabs/clips and snapping or securing into place; do not force
• After installation, restore power and verify airflow and temperature performance

This sump is the dishwasher drain pump housing that channels wash and drain water to the pump, helping the appliance clear water quickly to prevent standing water. A direct-fit replacement when the original housing is cracked or leaking. What it does:

• Houses and seals the drain pump to direct wastewater out of the tub
• Prevents leaks by maintaining a secure pump-to-tub connection
• Helps maintain proper drain flow to avoid standing water or incomplete drains
• Commonly replaced for visible cracks, leaks under the appliance, or when the pump seal fails

• One sump (drain pump housing) as shown

• Disconnect power and water supply before starting any repair
• Inspect adjoining gaskets, clamps, and pump for wear; replace if damaged
• Handle plastic components carefully to avoid cracking; tighten fasteners to OEM specs

This support is a factory-style replacement mounting bracket that helps secure internal components and restore proper alignment and stability. Designed to match original fit and function for a precise repair. What it does:

• Provides structural support for internal appliance components to reduce movement and noise
• Restores proper alignment of panels, shelves or assemblies that rely on the bracket
• Helps prevent binding or uneven wear caused by a failed or missing support
• Common symptom: rattling, sagging, misaligned panels or loose internal parts

• One support (mounting bracket) as shown

• Basic hand tools typically required; follow the appliance manufacturer's disassembly instructions
• Disconnect power and/or gas and shut off water (if applicable) before servicing
• Keep all fasteners and orientation of the old part for reference during reassembly