Kenmore 66513032K114 Parts

This insulated wire lead carries electrical current between components, restoring reliable power routing in your appliance. It's a direct-replacement discrete wire used where a single conductor is required for safe operation. What it does:

• Provides a single insulated conductor to connect terminals or components
• Restores proper electrical continuity when a wire is damaged, burned, or disconnected
• Helps prevent shorts by maintaining insulation between conductors
• Suitable for low- to moderate-current wiring routes within the appliance

• One insulated wire lead as shown

• Disconnect power before inspecting or replacing wiring to avoid shock or injury
• Route the wire as the original, avoiding sharp edges and heat sources; secure with existing clips or ties
• Replace any damaged terminals, connectors, or fasteners; use correct crimps or solder joints per OEM practice

This small cupshelf is the replacement door shelf insert that restores secure storage for cups, glasses and small items in your refrigerator door. It helps organize the door and prevents items from shifting or falling. What it does:

• Replaces a cracked, broken or missing small cupshelf to restore door storage capacity
• Supports cups, small glasses and lightweight containers on the refrigerator door
• Helps keep items organized and prevents sliding when the door opens or closes
• Matches OEM fit and mounting points when used as the specified replacement part

• One small cupshelf

• Remove items from the door and lift out the old shelf; align tabs and snap the new shelf into the existing door mounts
• No special tools are typically required; handle carefully to avoid damaging door trim or mounting tabs
• Always follow refrigerator power/safety guidance from the manufacturer when working near controls or lights

This replacement console assembly is the control panel housing that holds the selector switches, buttons and display, restoring the dryer/washer's user interface and appearance. Use it when the original console is cracked, broken or not responding. What it does:

• Replaces the exterior control panel and housing that secures switches and the display
• Restores button/knob mounting and helps correct loose, cracked or damaged controls
• Resolves common symptoms such as unresponsive buttons, visible damage to the console, or loose/misaligned control components
• Protects internal control components from debris and normal wear

• Disconnect power (and gas if applicable) before starting any repair
• Installation may require removing trim, bezels or screws and careful detachment of harness connectors
• Handle the console carefully to avoid damaging clips or the display lens

The Rail Stop Clip is an OEM replacement part for Whirlpool dishwashers. This clip is responsible for securing the upper dish rack to the rails of the dishwasher. A broken or worn-out Rail Stop Clip can cause the upper dish rack to become unstable or fall off the rails during operation. This can lead to dishes not being cleaned properly or even breaking during the wash cycle.

Causes of a bad rail stop clip can include wear and tear from frequent use, damage from overloading the racks, or breakage due to improper handling. Over time, the clip can also become brittle or warped, losing its effectiveness.

This part fixes the following symptoms:

• The dish rack sliding out too far or detaching from the dishwasher.
• Difficulty in pulling out or pushing in the dish rack smoothly.
• Noticeable absence or damage to the clip at the end of the rail.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The Inner Door Panel is an OEM part for Whirlpool dishwashers. Located inside the dishwasher door, this hard-wearing panel protects internal components from impact during loading. 

Symptoms of a bad inner door panel can include cracks or dents developing from normal use over many years. Mineral deposits may cause premature deterioration of door panel materials.

Causes of a bad inner door panel include repeated contact with dishes placed inside the washer door. Water pressure during cycles also contributes to standard wear and tear.

Symptoms of a bad inner door panel include:

• Damage exposes internal tubing, hoses, or electronics to risk
• Loss of protected support allows the door to bow outward  
• Compromised integrity permits unwanted vibration transfer 
• Reduced lifespan expectancy of door mount fittings and seals

This Whirlpool OEM replacement restores proper protection and structure. Compatible models include some KitchenAid, Jenn-Air, and select Kenmore units. 
 

Color: Black. Other colors: For white use 8171656, for biscuit use 8171657, for stainless steel use 8171659.

Color: Stainless steel. Other colors: For black use 8171657, for white use 8171656, for biscuit use 8171658.