Kenmore 79579993510 Parts

This funnel directs dispensed water or ice from the appliance's dispenser into your cup or container to reduce spills and ensure proper flow. It replaces a worn, cracked, or misaligned chute to restore clean dispensing. What it does:

• Guides water or ice from the dispenser to the user's cup or container
• Prevents drips and reduces splashing at the dispenser opening
• Helps position dispensed items so they clear the dispenser housing
• Addresses symptoms like leaking at the dispenser, uneven flow, or pieces falling inside the dispenser well

• One replacement funnel shown

• Disconnect power and water supply before starting any work
• Remove dispenser or front panel per your model's service instructions to access the funnel
• Align the funnel carefully with the mounting tabs and snap or fasten into place without forcing
• If clips or seals are damaged, replace them to ensure a secure, leak-free fit

This door stopper replaces the small hinge stop that limits door swing and helps the door close and latch properly. It restores correct door alignment and prevents the door from swinging past its intended range. What it does:

• Acts as a mechanical stop on the door hinge to control opening angle and reduce stress on the hinge
• Helps the door close smoothly and remain properly aligned
• Commonly replaces a cracked, worn, or missing stopper that allows over-rotation or uneven closing
• Can reduce noise and wear caused by a loose or shifting door

• Disconnect power to the appliance before servicing to avoid injury
• Replace like-for-like; removal may require removing the hinge trim or screws—keep fasteners organized
• Inspect adjacent hinge components and seals for wear while the door is removed

This drip tray catches and channels water runoff inside the appliance to help prevent pooling and minor leaks. It's a direct-fit replacement listed by the manufacturer and sold as the single tray used in the unit. What it does

• Collects condensate or defrost water and directs it to the drain area to prevent pooling.
• Helps stop water from dripping onto lower drawers, shelves or the floor.
• Commonly replaces a cracked, warped or missing tray that causes visible leaks or water buildup.
• Fits into the appliance's lower compartment where the original tray sat.

• Unplug the appliance or disconnect power before servicing.
• Remove any obstructing drawers or shelves to access the tray location; handle glass shelves carefully.
• Lift out the old tray and set the new tray into the same position; no special tools typically required.

A small protective cap that covers and protects a component connection or opening from dirt and moisture, helping maintain proper function and prolong component life. Simple replacement when the original cap is cracked, missing, or worn. What it does:

• Covers exposed fittings, terminals, or openings to keep out debris and moisture
• Helps prevent leaks or contamination at the sealed connection
• Restores a secure fit when the original cap is cracked, split, or degraded
• Commonly used where a small, removable protective seal is required

• Inspect mating surface and surrounding gasket/seal before installing; replace other damaged parts as needed
• Press the cap firmly into place until fully seated; no special tools usually required
• Wear gloves and disconnect power or water supply if working near energized or pressurized components

This communication link module provides the refrigerator's control board with network and user-interface connectivity so features and diagnostics can be accessed and controlled. It helps restore lost app or panel communication. What it does:

• Handles communication between the refrigerator's control system and external interfaces (user panel, network app).
• Works with the main control electronics to transmit status and diagnostic information.
• Replaces a damaged or non-communicating module that prevents remote control or smart features.

• One link (communication) module.

• Disconnect power to the appliance before replacing this electronic module to avoid shock or damage.
• Handle the module by its edges and avoid touching circuit contacts.
• Installation typically involves removing an access panel and unplugging/reconnecting a wiring harness; keep track of screw and connector locations.

This guide assembly is a molded support/aligning part used inside compatible TVs to secure and guide internal panels and components, helping maintain proper fit and stable operation. What it does:

• Holds and aligns internal panels or trim so screens and bezels sit correctly
• Prevents rubbing, rattling, or misalignment caused by loose or damaged guides
• Restores correct spacing between components after repair or collision
• Helps reduce vibration-related noise when installed properly

• One guide assembly

• Unplug the TV and place on a soft, flat surface before starting disassembly
• Removal typically requires partial cabinet/panel disassembly; keep fasteners organized
• Handle internal components and the guide carefully to avoid cracking plastic or damaging nearby cables

This display power control board assembly powers and controls the appliance's front display and user interface, restoring visible indicators and responsive touch/button controls when the display fails. It replaces a failed display/control PCB to return normal panel operation. What it does:

• Supplies power to the display and display backlight so status indicators and icons illuminate
• Interfaces between user controls (buttons/touchpad) and the main control, enabling command input
• Can resolve no-display, dim/flickering display, or unresponsive panel symptoms
• Prevents appliance from accepting inputs or showing status when the board fails

• One display power control board assembly

• Disconnect power to the appliance before starting to avoid shock or damage
• Handle the board by the edges and avoid touching components; observe ESD precautions
• Reassemble panels and connectors securely; test the display and controls after reconnection

This lamp cover is the replacement clear/white lens that protects and diffuses the appliance interior light, restoring proper illumination and preventing direct bulb contact. It helps keep the light assembly enclosed and looking finished. What it does:

• Protects the interior light bulb from spills, dust, and impact
• Diffuses light for even illumination inside the appliance
• Restores a cracked, yellowed, or missing lens to improve visibility
• Prevents direct contact with the bulb for safer operation

• One lamp cover (lens) as shown

• Remove power to the appliance before replacing the lens (unplug or shut off circuit)
• Typically snaps or screws into the light housing; use care to avoid breaking the new lens
• Inspect the light housing and bulb; replace bulb if damaged before reassembly