Kenmore 79641982410 Parts

Restore stable, level support with this replacement leg assembly. The adjustable foot steadies the unit on uneven floors, reducing vibration and rattling while allowing precise leveling for proper alignment and smooth, reliable operation.

• Provides adjustable support at the base of the unit
• Helps keep the appliance level on uneven or sloped floors
• Reduces wobble, vibration, and rattling noises
• Promotes proper door alignment and closure
• Replaces stripped, cracked, or missing leg assemblies

• Disconnect power; shut off water supply if applicable
• Carefully tilt and support the appliance to access the leg area
• Unthread the old leg; hand-thread the new assembly to avoid cross-threading, then fine-adjust with a wrench
• Level front-to-back and side-to-side; confirm stability before use

This pivot hanger assembly supports and stabilizes the appliance component it mounts to, restoring smooth movement and alignment. Replace a worn or damaged pivot to reduce noise and prevent misalignment that can affect operation. What it does:

• Acts as the pivot point for the hanger to support the drum/door assembly and maintain correct alignment
• Helps eliminate squeaks, scraping, or jerky motion caused by a worn pivot
• Prevents sagging or uneven movement that can lead to rubbing or binding
• Restores proper mechanical support so the appliance operates quietly and reliably

• Unplug the appliance or disconnect power before beginning any repair
• Basic hand tools may be required; follow the appliance service manual for disassembly steps
• Inspect surrounding components (mounts, bearings, fasteners) and replace if worn

This rear cover is the outer housing panel that protects the appliance's internal components and helps maintain proper airflow and support. It replaces a cracked, broken, or missing rear housing panel to restore protection and fit. What it does:

• Shields motors, wiring, vents, and other internal parts from dust, debris, and accidental contact
• Helps direct airflow and maintain correct ventilation for safe operation
• Restores proper mounting points and prevents rattles from a loose or damaged back panel
• Commonly replaced when there is visible damage, missing mounting tabs, or unusual noise from the rear

• One rear cover

• Disconnect power (unplug or switch off circuit breaker) before starting any repair
• Removal usually requires taking off the exterior panels and a few screws or clips; retain all fasteners for reinstallation
• Watch for sharp edges and wear protective gloves; handle internal wiring and components gently

This water level pressure switch senses the washer tub's water level and signals the control to start or stop filling. It restores accurate fill detection for proper wash cycles and helps prevent overfilling or improper operation. What it does:

• Detects water level via a vacuum hose and tells the control board when to stop filling
• Helps prevent overfill, underfill, and related cycle interruptions
• Can resolve symptoms like washer not filling, overfilling, or stopping mid-cycle
• Works as the sensing interface between the tub and the control system

• One water level pressure switch assembly

• Disconnect power and shut off water supply before replacing the part
• Note the vacuum hose routing and electrical connector locations before removal
• Handle the small vacuum hose and plastic fittings gently to avoid damage or air leaks

This holder is a small mounting bracket that secures internal components and keeps assemblies aligned for reliable operation. It replaces a worn or broken bracket to stop rattling and prevent parts from shifting. What it does

• Secures and positions nearby components or assemblies to maintain correct alignment
• Prevents vibration, rattling, or intermittent contact caused by a loose or cracked bracket
• Restores proper spacing so sensors, panels, or moving parts operate smoothly
• Helps prevent further wear or damage from misaligned parts

• One holder as shown

• Turn off power and disconnect the appliance before attempting any repairs
• Installation typically requires basic hand tools; save removed screws and clips for reassembly

This power cord assembly restores a secure electrical connection to your appliance so it can safely receive power. It replaces a worn, damaged, or faulty cord to help prevent interruptions and poor contact during normal use. What it does:

• Re-establishes the appliance's main power connection for reliable operation
• Replaces frayed, burnt, or damaged cord insulation and terminals
• Can stop intermittent power loss, sparking, or poor contact at the cord connection
• Provides the correct OEM-fit electrical cord and connector interface

• Always disconnect power at the breaker or unplug the appliance before starting work.
• Tighten terminal screws securely and avoid pinching or kinking the cord.

This drum spider is the rear support that attaches the washer's inner drum to the drive assembly, restoring stable spinning and reducing wobble, banging and vibration caused by a cracked or corroded support. What it does:

• Holds and centers the inner drum and transmits motor torque to the tub during spin cycles.
• Worn or broken spiders commonly cause loud banging, heavy vibration, or wobbling during spin.
• A failed spider can lead to uneven spinning and accelerate bearing or seal wear.
• Replacing the spider restores proper drum alignment and helps prevent further drivetrain damage.

• 1 drum spider

• Disconnect power and turn off water; drain the washer before beginning repairs.
• Replacement requires partial disassembly (removal of the outer/front panel and drum); follow for step-by-step instructions.
• Inspect tub bearings, seals and mounting hardware while the hub and shaft are exposed; replace any worn components to avoid repeat failure.

This outer tub assembly houses the inner wash tub and holds wash water, restoring the washer's ability to contain and direct water during cycles. Replaces a damaged or cracked outer tub to help stop leaks and restore normal wash function. What it does:

• Holds and channels wash water inside the washer during fill, wash and drain cycles
• Supports and centers the inner tub and agitator/spinning basket
• Helps prevent water from reaching the cabinet when intact
• Fault symptoms: visible cracks or damage, water leaking onto the floor, abnormal noise or banging during spin, or persistent balance issues

• One outer tub assembly

• Disconnect power and water supply before starting any repair
• This is a heavy component; get a helper and use proper lifting technique
• Installation typically requires removing the washer cabinet/front panel, drive motor and associated fasteners—follow the OEM service manual
• Inspect and replace seals, gaskets, clamps and mounting hardware as needed

This main control board is the appliance's primary power/control electronics assembly that manages functions and user interface signals. Replacing a faulty board restores proper electronic control and device responsiveness. What it does:

• Receives and distributes power to control circuits and coordinated components
• Interprets user commands and sends control signals to motors, valves, or compressors
• Replaces a board that can cause erratic operation, unresponsive controls, or failure to power on
• Helps resolve intermittent operation or loss of certain electronic functions tied to the control system

• One main control board

• Disconnect power before service to avoid shock or damage
• Handle the board by the edges and avoid static discharge; use an anti-static strap if available
• Note connector locations and orientation before removing; reconnect all wiring harnesses firmly

This frame assembly replaces the outer trim around the appliance door to restore fit, finish, and proper sealing. It refreshes the appearance and helps the door close and align correctly after damage or wear. What it does:

• Provides the outer structural trim for the appliance door and secures door components in place
• Restores proper door alignment and helps maintain a consistent seal around the door edge
• Fixes cosmetic damage such as cracks, dents, or broken trim that affect appearance
• Can reduce rattling or misalignment caused by a warped or damaged frame

• Disconnect power and, if applicable, gas before starting any repair
• Handle glass and trim carefully to avoid damage or injury; use gloves and eye protection
• Minor disassembly of the door or surrounding trim panels is typically required; keep screws and small parts organized

This power control board assembly manages a range of electrical functions to help your appliance run correctly and respond to user inputs. Replacing a failed board restores control of cycles, power delivery, and timed operations. What it does:

• Regulates and distributes power to motors, valves, heaters, and electronic components
• Interprets user controls and sends signals to start, stop, or change cycles
• Helps resolve symptoms like no power, unresponsive controls, or intermittent operation
• Can address fault codes tied to control or power delivery failures

• Disconnect power before attempting diagnosis or replacement to avoid shock or damage
• Handle the board by edges and avoid touching components or connectors; static discharge precautions recommended
• Confirm connector orientation and secure all wire harnesses before restoring power

This PCB assembly is the electronic control module that manages appliance functions and signals, restoring proper electronic operation when the original control board is damaged or fails. It provides the necessary circuitry for timed cycles and user-interface communication. What it does:

• Controls electronic commands and coordinates operation of the appliance's systems
• Replaces a failed or damaged control board that can cause unresponsive controls, erratic behavior, or intermittent operation
• Transfers settings and signals between user controls and mechanical components
• Helps resolve faults related to control logic and communication errors

• One PCB assembly

• Always disconnect power (unplug or switch off the breaker) before servicing electrical components
• Handle the board carefully and avoid touching contacts; use ESD precautions if available
• Verify connector alignment and seating; do not force connectors onto pins