Kitchenaid Krff305ess00 Parts

This genuine replacement door gasket creates an airtight seal around the refrigerator door to help maintain proper temperature and efficiency. It restores sealing performance to reduce frost buildup and stabilize internal cooling. What it does:

• Seals the refrigerator door edge to keep cold air in and warm air out
• Helps prevent frost and ice buildup in the freezer/refrigerator compartment
• Reduces compressor run time caused by a leaking door seal
• Improves temperature consistency for food preservation

• Disconnect power to the appliance before starting any work
• Clean and dry the door flange thoroughly before installing the new gasket
• Press the gasket into the channel evenly, working around the door to align the magnetic lip
• Inspect the seal after installation and allow normal operation to seat the gasket; check for gaps and re-seat if needed

This oven cavity insulation panel helps keep heat inside the oven for more even cooking and reduces heat transfer to surrounding cabinetry. Replace damaged or missing insulation to restore proper oven temperature stability and efficiency. What it does:

• Provides thermal barrier around the oven cavity to limit heat loss
• Helps maintain even baking and cooking temperatures
• Reduces excess heat reaching surrounding surfaces and components
• Can prevent hot spots, burning smells, or smoky operation from deteriorated insulation

• Disconnect power (and gas, if applicable) before beginning any service
• Remove oven doors and panels as needed to access the insulation; follow OEM service instructions
• Handle insulation with gloves to avoid irritation and avoid compressing or tearing the material

This insulation panel helps reduce heat transfer in the refrigerator cabinet so the appliance holds cold temperatures more efficiently and reduces frost buildup. It's a direct-fit replacement for the factory cabinet insulation. What it does:

• Slows thermal transfer between the cabinet and ambient air to help maintain interior temperatures
• Helps reduce frost buildup on evaporator and interior surfaces
• Improves cooling efficiency by minimizing cold-air loss
• Quietly adds a layer of thermal and acoustic insulation behind the liner

• Disconnect power and remove food before starting any repair
• Access requires removing the interior liner or trim
• Handle gently and wear gloves; insulation can tear or shed fibers
• Follow OEM instructions for adhesive or fastener placement and secure fit

This tempered glass shelf provides a sturdy, easy-to-clean storage surface for your refrigerator, restoring usable shelf space and helping keep foods organized and contained. What it does:

• Replaces a cracked, chipped or missing refrigerator shelf to restore stable storage
• Provides a flat, durable surface for storing plates, containers and groceries
• Helps contain minor spills and makes cleanup quick with a smooth glass surface
• Sits into existing shelf supports or rails to align with refrigerator storage layout

• One tempered glass refrigerator shelf

• Handle carefully; tempered glass can break if dropped or struck
• Slide the shelf straight into the existing support rails—do not force or bend rails
• Confirm the shelf is fully supported on both sides before loading
• Clean with mild soap and water; avoid abrasive cleaners

The door hinge is an OEM part for Whirlpool refrigerators. It plays a role in holding the refrigerator door securely in place while allowing it to swing freely for easy access. The hinge is designed to withstand the pressure of opening and closing the door smoothly over many years of use.

Causes of a bad hinge include wear and tear from repeated opening and closing of the door, exposure to excessive force or impact, or overloading of the door with heavy items.

Symptoms of a bad hinge include:

• The door not closing properly or unevenly
• Increased effort required to open or close the door
• Noises or squeaking coming from the hinge area
• The door leaning or not staying securely closed

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This glass shelf replaces a damaged or missing refrigerator shelf to restore stable storage and easy cleaning. It provides a flat, durable surface for food and containers and keeps items organized. What it does:

• Supports food, pitchers and containers on a stable, easy-to-clean surface
• Allows airflow and visibility while maximizing usable shelf space
• Replaces cracked, chipped or broken glass that can cause instability or safety hazards
• Helps prevent spills from spreading to lower compartments when intact

• Remove food and any loose shelving hardware before installing
• Handle glass carefully and wear gloves to avoid cuts from edges or chips
• Slide shelf into existing shelf rails or supports until seated securely
• If shelf does not align with rails, do not force

This replacement cover protects water-related components on select Whirlpool washers, helping keep valves and hoses shielded from debris and incidental contact for reliable water flow management. What it does

• Protects water valves, inlet hoses, and nearby fittings from dirt and accidental contact
• Helps maintain proper water routing by keeping components covered and positioned
• Commonly replaced if cracked, broken, warped, or missing after impact or wear
• Can prevent debris buildup that interferes with valve operation or connections

• One replacement cover as pictured

• Disconnect power and shut off the water supply before starting any repair
• Secure with existing screws or clips
• Do not force the cover into place; inspect surrounding fittings and hoses for damage while installing
• If you see leaks after installation, recheck hose connections and valve seating; replace defective parts as needed

This housing is the replacement outer tub housing that supports and secures the washer tub and related drive components for proper alignment and operation. Restores stable drum mounting and reduces abnormal motion. What it does:

• Supports the washer's tub/drum assembly so the drum spins smoothly and stays aligned
• Provides a mounting surface for suspension and drive components to reduce vibration and noise
• Helps prevent rubbing or scraping by keeping internal components correctly positioned
• Commonly replaced when the tub feels loose, spins unevenly, or makes unusual noises

• One housing

• Disconnect power to the appliance before beginning any repair
• Handle with care to avoid damaging seals, sensors, or surrounding trim pieces
• Verify correct orientation and torque for fasteners; follow OEM service manual steps

This control panel bezel cover protects the appliance's control area and gives the front a finished appearance while keeping buttons and displays free of dust and spills. It's a direct-replacement exterior trim piece used when the original cover is cracked, scratched, or missing. What it does:

• Protects the control panel and button assembly from dust, moisture, and everyday wear
• Restores a clean, finished look to the appliance front
• Helps keep buttons and displays clear and unobstructed for reliable operation
• Commonly replaced when the original cover is cracked, broken, or cosmetically damaged

• One control panel bezel cover

• High-level replacement only; remove power to the appliance before beginning any work
• Some covers attach with screws or clips; keep fasteners and alignment tabs during removal
• Use caution to avoid scratching surrounding surfaces during removal and installation

This evaporator clip secures the refrigerator evaporator assembly and related components so the cooling system stays aligned and vibration-free. It helps maintain proper airflow and prevents rubbing or loose parts. What it does:

• Holds the evaporator coil/assembly or associated covers in place
• Prevents vibration, noise, and contact between the coil and cabinet parts
• Helps maintain consistent airflow for reliable cooling performance
• Commonly linked to rattling, buzzing, or loose parts around the freezer evaporator

• Disconnect power before servicing the appliance
• Handle evaporator and surrounding fins carefully; they are sharp and fragile
• Verify clip orientation against the OEM diagram before fastening

This replacement oven door handle restores a secure grip for opening and closing the oven door. It replaces a damaged, loose, or missing handle to make door use safer and more convenient. What it does:

• Provides a sturdy grip for opening and closing the oven door
• Replaces handles that are cracked, bent, loose, or missing
• Helps prevent slippage and improves user control when handling hot appliances
• Matches the original mounting style for a straightforward replacement

• Use basic hand tools; support the door while removing and installing the handle to avoid injury or damage
• Disconnect power to the appliance or ensure it is cool before attempting replacement
• Tighten mounting fasteners securely but do not overtighten to avoid stripping