Ksc525fvmk03 Parts

This heating element assembly restores heat to your dryer so clothes dry efficiently and cycle times return to normal. It replaces a failed or intermittent heater to help eliminate no-heat or low-heat drying problems. What it does

• Produces the heat needed to dry laundry during a dryer cycle
• Replaces a broken or burnt-out element that can cause no-heat or long dry times
• Works with the dryer's thermal cutoffs and cycling thermostat to regulate temperature
• Helps prevent overheating when used with functioning safety thermostats

• One heating element assembly

• Disconnect power before servicing; this is an electrical component
• Inspect and replace related safety thermostats or fuses if they show damage

This rubber grommet provides a tidy, protective seal where hoses, wires, or shafts pass through the appliance cabinet—helping prevent chafing, reduce vibration noise, and maintain proper sealing around openings. What it does:

• Cushions and protects wiring or hoses from rubbing against metal edges
• Helps maintain a seal to reduce water or air bypass where fitted
• Dampens vibration and reduces related noise at the penetration point
• Keeps openings finished and helps prevent further component wear

• Disconnect power (and water for washers) before starting any repair
• Inspect the mounting area for sharp edges or damage; replace if surrounding parts are compromised
• Push the grommet into the opening and seat evenly; do not stretch excessively

This screw secures appliance components to restore proper fit and stop parts from shifting. Replacing a missing or damaged screw helps eliminate rattling and keeps panels, trim and small assemblies aligned during normal use. What it does:

• Fastens panels, brackets, trim or small internal assemblies to maintain structural fit.
• Replacing a worn or missing screw can stop rattling, vibration or loose parts.
• Uses OEM-design fit and thread profile for correct engagement and to avoid stripped threads.
• Intended for use in specific Whirlpool assemblies.

• Disconnect power and, if applicable, shut off gas or water supply before servicing.
• Start threads by hand to avoid cross-threading; use the correct driver bit for the screw head.
• Tighten snugly but do not overtighten — overtightening can strip threads or damage components.
• If threads or inserts are damaged, replace or repair per OEM instructions before reinstalling.

This inverter box is the control module that converts and regulates power for the compressor motor in compatible refrigerators, enabling proper compressor operation and efficient cooling performance. What it does:

• Supplies and regulates the variable power signal to the refrigerator compressor motor
• Helps the compressor start and run at the correct speed for temperature control
• Can cause no cooling, intermittent compressor operation, or frequent start/stop if faulty
• Works with the main control and compressor to maintain stable refrigeration performance

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Handle the module carefully and avoid contact with circuitry; observe ESD precautions if available
• Verify connectors and mounting position match the original before finalizing installation

A small replacement pin that secures the flipper emitter assembly, restoring correct movement and alignment so the flipper can engage and operate reliably. Ideal when the original pin is bent, worn, or missing. What it does:

• Holds the flipper emitter or lever in place so the mechanism can pivot correctly
• Restores proper movement when a loose or broken pin causes misalignment
• Helps stop clicking, scraping, or intermittent operation related to a damaged fastener
• Serves as a direct-fit replacement designed for the OEM emitter/lever assembly

• One replacement pin as shown

• Disconnect power to the appliance before beginning any repair
• Handle small parts carefully; keep screws and pins organized during disassembly
• Use basic hand tools; no special tools or adhesives are typically required

A thermistor assembly that measures refrigerator temperature and sends that data to the control board so the appliance can regulate cooling. Replaces a failed sensor to help restore accurate temperature control. What it does:

• Senses internal temperature and converts it to a signal the control board uses to adjust cooling.
• Helps regulate compressor, evaporator, and defrost cycles when operating correctly.
• Common symptom: erratic or incorrect refrigerator/freezer temperatures.
• Common symptom: cooling failure, long run times, or temperature-related error codes.

• Disconnect power before accessing or replacing the thermistor to avoid shock.
• Handle the sensor element and wiring gently; avoid pinching or crimping the leads.
• Install in the same location and orientation shown in the OEM diagram for reliable readings.

This spring-style tube clamp secures flexible tubing to fittings, helping prevent leaks and maintain proper flow. It's a simple replacement that restores a firm seal on water or drain lines. What it does:

• Keeps flexible tubing firmly clamped to barbed or nipple fittings
• Helps stop or reduce leaks from loose or corroded connections
• Prevents tubing from slipping off under pressure or vibration
• Useful where a compact, spring-action clamp is required

• Disconnect power and shut off water to the appliance before replacing parts
• Use pliers to expand the clamp, position it over the tube/fitting, then release to secure
• Inspect connected tubing and fittings for damage; replace if cracked or severely corroded

This is the cup-style water fill used to direct or hold incoming water in the appliance's water delivery system, helping proper flow to the dispenser or ice/water components. It replaces a cracked or damaged fill cup to restore reliable water routing. What it does

• Directs incoming water to the dispenser/ice fill area so water reaches the correct channel
• Prevents water from leaking into surrounding compartments when intact
• Commonly replaced when cracked, warped, or causing pooling or poor fill performance
• Works as a passive funneling/holding component in the fill path

• One cup (water fill) as described

• Disconnect power and shut off the water supply before starting work
• Handle carefully to avoid cracking plastic; inspect seals/gaskets and mounting points
• Reinstall per appliance service instructions; secure fasteners and check for proper alignment
• After installation, restore power/water and test the dispenser/fill function for leaks

This electronic control board manages the appliance's user interface and core cycle functions so your unit responds correctly to selections and timing. It restores control logic and cycle sequencing for reliable operation. What it does:

• Routes user commands from the console to actuators, valves, and motors
• Manages cycle timing, display indicators, and status feedback
• Helps stop unresponsive panels, incorrect cycle behavior, or failure to start when the control has failed
• Can clear intermittent faults caused by a damaged or non-responsive control

• One electronic control board

• Disconnect power at the breaker or unplug the appliance before servicing
• Handle the board carefully and avoid touching circuit traces or components
• Reinstall with correct mounting and connector engagement; loose connections can cause faults

Color: White. Size: 13 oz. Spray paint primer. can.

This steel rivet secures appliance panels and small components, restoring proper fit and preventing rattles or loose parts. It's a straightforward replacement when a worn or missing rivet causes instability. What it does

• Fastens sheet metal or trim pieces to the cabinet or internal brackets
• Restores secure mounting when a previous rivet has sheared or fallen out
• Stops panel vibration or rattling caused by a loose fastener
• Provides a permanent, non-threaded mechanical connection for components

• Replacement typically requires a rivet tool or rivet setter; drill-out may be needed to remove a broken rivet
• Match rivet type and length to the original for a secure fit
• Disconnect power and follow all safety precautions before accessing internal parts

This small retainer clip secures components in place to prevent shifting, vibration, or wire movement during appliance operation. Replacing a fatigued or missing clip restores a firm hold and helps eliminate rattles or intermittent connections.

• Holds parts, panels, or wiring securely to their mounting points
• Helps reduce vibration, noise, and wear from loose components
• Common fix when a panel, trim, or harness won't stay attached
• Symptoms can include rattling, loose wiring, or parts popping free

• Unplug the appliance before servicing; shut off water or gas if applicable
• Note original clip orientation and location before removal
• Use needle-nose pliers if needed to compress/position the clip
• Do not overtension; seat fully without deforming mating parts

This dairy compartment door replaces the small interior door that covers the refrigerator's dairy/bin area, restoring a sealed, accessible storage space for butter and small items. It helps keep contents contained and organized. What it does:

• Replaces a cracked, broken, or missing dairy compartment door
• Restores the door that covers the dairy/bin shelf so items stay contained
• Helps maintain a neat interior and makes the dairy area easier to access
• Compatible with refrigerators that use this specific replacement door design

• One dairy compartment door

• High-level replacement: usually snaps or slides into the dairy bin track—inspect mounting tabs before installing
• Use gentle pressure to avoid breaking plastic tabs; replace any damaged clips or supports
• Disconnect power and remove food from the area if removing shelves or bins during installation

Color: Stainless

This top washer lid replaces a cracked, broken, or warped cover to restore safe, clean operation and a finished appearance. It protects the wash tub, helps contain water and laundry, and lets the lid latch and close properly. What it does:

• Covers the washer tub to keep water and clothing inside during operation
• Restores a secure surface that allows the lid to close and the latch to engage
• Replaces cosmetic damage like cracks, chips, or heavy wear
• Helps reduce noise and prevents accidental access to the wash tub

• Disconnect power and water before starting any repair
• Typical installation requires removing hinge screws and aligning the lid on the hinge pins
• Handle carefully to avoid scratching painted surfaces; two-person lift may be needed for larger lids
• If latch or hinge hardware is damaged, inspect and replace those parts separately

This evaporator fan motor assembly circulates cold air across the evaporator coils to maintain even refrigerator/freezer temperatures. Replaces a worn or noisy fan to restore proper airflow and cooling performance. What it does:

• Moves air across the evaporator coils to help the appliance cool efficiently
• Helps reduce frost buildup by maintaining steady airflow over coils
• Commonly replaced for symptoms like loud fan noise, weak airflow, or uneven cooling
• Designed as a motor with attached scroll-style fan (impeller) for direct fit operation

• Disconnect power to the appliance before beginning any service to avoid electrical shock
• Handle the fan blades carefully to avoid bending or damage that can cause vibration
• Some installations require removing interior panels or the evaporator cover; keep track of screws and clips
• If the connector or mounting hardware appears damaged, replace with OEM-equivalent parts for safe operation