Kses530sps Parts

This heat shield protects oven cavity components from direct heat and helps maintain correct temperature distribution for reliable cooking. It replaces a damaged or warped shield to help prevent heat-related wear. What it does:

• Deflects and disperses radiant heat away from sensitive panels and wiring.
• Helps maintain even internal oven temperatures for consistent cooking.
• Prevents heat damage to insulation, wiring, and nearby components.
• Common symptom: visible warping, burn marks, or a detached/damaged shield.

• Disconnect power (and gas if applicable) before starting any repair.
• Wear gloves to protect against sharp edges and hot surfaces.
• Reinstall using the original fasteners; verify proper alignment and clearance.
• Follow the appliance manufacturer's instructions and diagrams for safe, correct installation.

A replacement wire insulation sleeve that protects appliance wiring from heat, abrasion and vibration to help maintain safe electrical connections. Installs quickly to restore proper insulation on exposed or damaged wiring. What it does:

• Shields wiring from heat and rubbing that can wear or melt insulation
• Helps prevent electrical shorts and intermittent power caused by chafed wires
• Holds wiring away from sharp edges and moving parts
• Used where original insulation has cracked, split or burned

• One wire insulation sleeve

• Disconnect power to the appliance before starting any work
• Slide sleeve over the wire and position to fully cover the exposed area; secure per OEM routing and retainers
• Inspect nearby wiring and components for heat or abrasion damage and replace if needed

This bezel-knob replaces a worn, cracked or missing control knob trim to restore a finished look and proper fit around the control shaft. It helps keep the control knob centered and improves usability of the control panel. What it does:

• Replaces damaged or cosmetic bezel around a control knob
• Centers and stabilizes the control knob on the control shaft
• Restores a finished appearance to the control panel
• Helps eliminate wobbling, binding, or misalignment when turning controls

• Disconnect power to the appliance before beginning any service
• Typically installs by aligning over the control shaft and pressing into place; panel removal may be required on some models
• Use care to avoid damaging surrounding trim or control components during installation

This glass cooktop surface replaces a damaged or worn top on compatible electric cooktops, restoring a smooth, stable cooking area and a clean appearance. Ideal when the original top is cracked, scratched, or no longer seats properly. What it does:

• Provides the flat, heat-resistant surface that supports cookware and covers the heating elements
• Restores a flush seal and finished look to the cooktop area
• Replaces surfaces that are cracked, chipped, crazed, or otherwise cosmetically damaged
• Helps prevent debris from falling into the burner area and simplifies cleaning

• Disconnect power to the appliance before starting any work; follow all safety instructions
• Installation typically requires removing control knobs and lifting the old top; handle glass carefully to avoid breakage
• Have a second person assist for alignment and lifting of larger tops

The Hardware Kit is an OEM part for Whirlpool ranges. This comprehensive kit includes all mounting screws and clips necessary for properly securing multiple internal components.  

The precise hardware pieces maintain and reinforce structural connections between panels, drawers, doors, and electronic assemblies throughout daily use. Corrosion-resistant coatings ensure stability over time.

Causes of damaged or missing hardware include normal wear from repeated installation/removal of panels during repairs or self-maintenance. Improper installation techniques could also stress components.

Symptoms of insufficient hardware include: 

• Gaps emerging between assembled surfaces
• Rattling noises from loose parts  
• Doors or drawers becoming misaligned  
• Interior panels unable to properly support weight

Also compatible with some Maytag, KitchenAid, Jenn-Air, and Kenmore ranges and ovens. 

The Vent Trim is an OEM part for Whirlpool ranges. It enhances the appearance of your kitchen while providing a finished look to the range vent area. It covers the gaps and edges around the range vent, creating a clean design.

A bad vent trim can occur due to wear and tear, accidental damage, or improper installation. If you notice symptoms such as loose or missing trim, gaps around the vent area, or an uneven and unfinished look, it may be time to replace the vent trim.

Symptoms of a bad vent trim include:

• Loose or missing trim
• Gaps around the range vent area
• Uneven and unfinished appearance

Repair your range by replacing the worn-out or damaged vent trim with this genuine OEM part.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

This replacement bumper cushions and protects the appliance door or panel, helping stop metal-on-metal contact, reduce noise, and prevent chipping or wear. Simple, low-profile part that restores smooth, quiet door operation. What it does:

• Cushions door or panel to prevent hard impacts and protect finishes
• Reduces rattling and vibration-related noise during operation
• Helps the door close more softly and sit flush with the cabinet
• Prevents premature wear where edges contact the cabinet

• Disconnect power to the appliance before starting any repair.
• Inspect the damaged bumper and surrounding area, then remove the old bumper by hand or with a non-marring tool.
• Press the new bumper into the original mounting location until fully seated; no special tools normally required.
• If the bumper mounts to a clip or bracket that's damaged, replace the bracket.

This is a replacement mounting screw used to secure appliance panels and components. It restores proper fastening so panels and parts stay aligned and stable during normal use. What it does:

• Fastens appliance panels, trim or internal components in place
• Replaces missing or stripped screws that cause rattling or loose parts
• Helps stop panel vibration and maintain proper component alignment
• Matches OEM fit where specified for a secure installation

• One replacement mounting screw

• Verify screw size and fit before installation; use the correct screw location from your parts diagram
• Turn off and disconnect power to the appliance before accessing internal components
• Hand-start the screw to avoid cross-threading; tighten until snug—do not over-tighten
• Wear safety glasses and follow manufacturer service instructions when applicable

This end cap is the outer trim piece that finishes and protects the edge of a appliance panel, restoring a clean appearance and helping keep the panel properly aligned. Ideal for replacing a cracked, missing, or worn end cap. What it does:

• Covers and protects the outer edge of a control or access panel to prevent snagging and moisture intrusion
• Helps hold the panel edge flush for a finished look and proper fit
• Replaces cracked, broken, or otherwise damaged trim that affects appearance or panel alignment
• Matches the OEM shape and attachment points for a direct replacement when part numbers match

• Disconnect power to the appliance before starting any repair
• Usually installs with a few screws or snap clips; keep hardware from the original part when possible
• Handle edges carefully to avoid scratching adjacent surfaces during installation

This door liner is the oven's inner door panel that helps protect the door cavity and support the inner glass. Replaces a damaged or worn liner to restore a clean interior surface and proper glass fit. What it does:

• Replaces the oven's inner door panel that secures the inner glass and insulation
• Restores a sealed, smooth interior door surface to help contain heat and cooking messes
• Helps eliminate rattles or misalignment caused by a cracked or bent liner
• Compatible with ovens that specify part number W10902192

• One inner oven door liner

• Refer to the oven model's service manual for step-by-step disassembly and reassembly
• Disconnect power (and gas if applicable) before starting work
• Handle the glass and liner carefully—wear gloves and eye protection to avoid cuts
• If other door components are damaged, inspect and replace them as needed for a complete repair

This replacement screw restores secure fastening for appliance panels and components, helping stop loose parts and rattling so controls and panels stay aligned. Use when original screws are missing, stripped, or damaged. What it does:

• Secures panels, trim, control boards, brackets, or components to the appliance frame
• Stops rattling, vibration noise, and loose or misaligned parts caused by missing or damaged fasteners
• Replaces stripped, corroded, or missing screws to restore proper fit and function
• Matches OEM fit and threading for straightforward hardware replacement when the correct screw is identified

• Turn off power and unplug the appliance before accessing internal components
• Use the correct screwdriver or bit to avoid stripping the head; do not force mismatched drivers
• Tighten until snug—do not overtighten, which can strip threads or crack plastic
• Keep removed hardware organized and verify the replacement screw matches the original before installation

This glass spacer positions and cushions oven door glass to keep panels aligned and prevent direct glass-to-glass contact. Replacing a damaged spacer restores proper door fit and reduces rattling or uneven sealing. What it does

• Separates and spaces oven door glass panels to prevent rubbing and stress cracks.
• Cushions the glass to reduce vibration and noise during operation.
• Helps maintain even door alignment for a tighter closure and consistent heat containment.
• Commonly replaced when the spacer is worn, cracked, missing, or allowing glass to contact adjacent parts.

• One glass spacer

• Disconnect power to the appliance before starting any repair.
• Handle glass and the spacer with care; wear safety gloves and eye protection.
• Removal/installation typically requires partial door disassembly—retain fasteners and note orientation.
• If door glass is cracked or loose, replace damaged glass to avoid injury.

This insert is a small OEM component designed to fit into a specific location on your appliance to secure, align, or finish an assembly. Replacing a worn, damaged, or missing insert restores proper fit and clean appearance.

• Provides a snug interface or cover within the designated assembly
• Helps prevent looseness, vibration, or gaps in the connected part
• Replaces cracked, worn, or missing insert pieces
• Common symptoms include loose or wobbly parts, misalignment, or a missing cap/cover

• Disconnect power and shut off gas/water before servicing
• Refer to your model's parts diagram to confirm location and orientation
• Use non-marring tools to avoid cosmetic damage
• Seat the insert fully; do not overtighten adjacent fasteners

The Control-Electric is an OEM part for Whirlpool ranges. It houses the digital controls that allow users to set various cooking functions and temperatures with ease. 

Causes of a faulty control board can include liquid damage, overheating, power surges, or regular component failures over many usage cycles.

Symptoms of a bad control board include:

• Unresponsive or inaccurate buttons and dials
• Erratic or incorrect temperature readings
• Inability to ignite burners or turn on oven lights
• Blank or non-functioning display screens

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This electronic display/user interface assembly mounts behind the control panel and handles button inputs and the visual readout. Replacing a failed board restores a readable display and responsive controls so you can set and monitor functions reliably.

• Drives the control panel display and indicator lights
• Interprets keypad/touch inputs and sends commands to the appliance
• Interfaces with the main control to execute selected functions
• Typical symptoms: blank or dim display, unresponsive or erratic buttons, incorrect readouts, or UI-related error codes

• Disconnect power before servicing; use ESD protection when handling electronics
• Access through the control panel; note screw and clip locations during disassembly
• Transfer any model-specific brackets, trim, or insulators from the original part as required
• Seat wire harness connectors fully; restore power and perform any model-specific UI reset or calibration.