Ksf26c4xyy Parts

This ice bin latch assembly secures the refrigerator's ice container so it stays seated and aligned with the auger drive. Replace a worn or broken latch to restore consistent ice dispensing and a snug fit.

• Locks the ice bin in place and aligns it with the auger/dispenser drive
• Helps prevent the bin from wobbling, shifting, or popping loose
• Can resolve no or intermittent ice dispensing caused by bin misalignment
• Direct replacement when the latch is cracked, worn, or missing

• Disconnect power to the refrigerator; turn off the water supply if needed
• Remove the ice bin to access the latch area
• Release retaining tabs/fasteners, note orientation, and install the new latch assembly
• Verify smooth latch engagement before reinstalling the bin and restoring power

The Ice Chute Mounting Bracket is an OEM replacement part for Whirlpool side-by-side refrigerators. It securely positions the removable ice chute opening above the storage bin.

Causes for bracket failure involve standard wear from long-term usage. Repeated lifting of the chute subjects mounting screws and anchors to consistent force strains over many seasons. 

Symptoms requiring replacement involve:

• Loose, sagging or detached ice chute positioning
• Lost or stripped mounting fasteners  
• Ice jamming or spillage due to misaligned openings
• Safety hazards from potential pinch points

This authentic Whirlpool replacement is compatible with Jenn-Air, KitchenAid and Maytag panel-ready stainless steel refrigerators as well.

Color: White

The Door Hinge is an OEM part for Whirlpool refrigerators. It acts as the pivot point that allows the fresh food door to open and close smoothly. As a moving component subjected to frequent use, the hinge can become loose or misaligned over time.

Causes can be normal wear and tear, excessive force on the door, or improper alignment over repeated use. Installation of this genuine replacement restores reliable door function.

Symptoms of a bad hinge include:

• The door not closing or sealing properly
• Difficulty opening and closing the door
• Noises or squeaking coming from the hinge area

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Color: Black

Color: Mist Beige

This dual water tube routes water along two separate paths inside the refrigerator, supplying components such as the dispenser and ice maker. Replacing a cracked, kinked, or clogged tube restores steady flow and helps prevent leaks. What it does:

• Carries pressurized water to two internal destinations
• Helps supply the dispenser and/or ice maker
• Replaces tubing that is cracked, brittle, kinked, or leaking
• Typical symptoms: leaks behind/under the fridge, slow/no dispenser flow, ice maker not filling or making small/hollow cubes

• Unplug the refrigerator and shut off the water supply before servicing
• Place a towel or container to catch residual water when disconnecting lines
• Note original routing and connection points; transfer any guides/clips as needed
• Fully seat tubing in quick-connect fittings, tug-test for engagement, restore water, and check for leaks

This cam-door is the small plastic cam that helps the appliance door latch and move smoothly. Replacing a worn cam restores reliable door engagement and reduces slamming or misalignment. What it does:

• Guides and secures the door latch mechanism for proper opening and closing
• Helps align the door to prevent gaps or uneven sealing
• Reduces noisy or rough door movement caused by a worn cam
• Common symptom: door won't stay closed, feels loose, or binds when opening/closing

• One cam-door as shown

• Disconnect power (or unplug) before starting any repairs
• Access may require removing the outer door panel or trim—keep fasteners organized
• Handle small plastic parts carefully to avoid cracking; replace any damaged clips or screws

Color: Black

The Dispenser Actuator is an OEM part for Whirlpool refrigerators. It is responsible for controlling and actuating the dispensing of water and ice from the refrigerator door. The dispenser actuator contains electronic components that sense when a cup is placed in the dispenser area and signal the water and ice systems to operate. 

Symptoms of a bad dispenser actuator include:

• Failure to dispense water or ice
• Water or ice dispensing continuously without a cup present  
• Delayed or inconsistent response time when dispensing
• Electronic control issues such as blinking lights or error codes

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Replacement screw that secures panels, brackets, and other components inside your appliance, keeping assemblies tight and aligned. Replace missing or stripped hardware to eliminate looseness, reduce vibration, and restore a solid, factory-fit hold.

• Fastens panels, brackets, trim, or internal components
• Helps maintain alignment and reduce rattling/vibration
• Replaces missing, loose, rusted, or stripped hardware
• Common signs: stripped head/threads, loose panel, buzzing/rattling noises

• Disconnect power before service; shut off gas/water if applicable
• Match to the original screw; start threading by hand to avoid cross-threading
• Use the correct driver size to prevent stripping
• Tighten snugly; do not overtighten. If it won't hold, inspect the receiving hole/clip

This water connector is an inlet fitting that connects the household water line to the appliance, providing a secure path for water to reach the valve, dispenser or ice system. It helps maintain proper water flow and prevents leaks when installed correctly. What it does:

• Connects the incoming water supply to the appliance's inlet valve or ice/dispenser plumbing
• Provides a sealed transition between supply tubing and appliance fittings
• Restores normal water flow for ice makers and dispensers when damaged or corroded
• Can prevent dripping or pooling from a failing or broken connector

• Turn off the appliance power and shut off the house water supply before replacing
• Inspect and replace any worn tubing, O-rings, or clamps for a proper seal
• Hand-start threads to avoid cross-threading, then snug with a wrench—do not overtighten
• After installation, restore water and power and check all connections carefully for leaks

The Dispenser Drip Tray is an OEM part for Whirlpool refrigerators featuring internal or through-the-door dispensers. Located below the dispenser mechanism, it collects residual liquid and prevents spills. The drip tray's angled design helps direct any drips into its drainage port.

Symptoms of a faulty dispenser drip tray include:

• Puddles or spills below the dispenser area
• Wetness inside refrigerator walls near the dispenser system  
• Mold growth from unattended moisture collecting

Causes may involve cracks that create leaks, clogged drains impair drainage, or a loose or damaged seal around the tray.

This OEM replacement fits many Whirlpool, Maytag, KitchenAid and Kenmore models.

This ice bin collects and stores ice made by the refrigerator's ice maker so you can access and dispense cubes easily. It restores a secure place for ice to accumulate and prevents loose ice from spilling in the freezer. What it does:

• Holds and organizes ice produced by the ice maker so cubes are ready to use
• Keeps ice contained to prevent spills and frost buildup in the freezer compartment
• Replaces cracked, warped or missing bins that allow ice to leak or jam dispenser mechanisms
• Works with compatible freezer ice makers to maintain normal ice storage

• Slide the bin into the ice maker housing or designated freezer shelf until it seats; no tools usually required
• Unplug or disconnect power to the appliance before servicing to avoid electrical hazards
• Handle the bin carefully to avoid cracking plastic; avoid forcing into place

The Bracket is an OEM part for Whirlpool-brand refrigerators. These brackets are mounted internally to provide secure anchoring points for door assemblies on the refrigerator frame.

Causes of a bad bracket can include cracks from over-tightening during installation, or metal fatigue over many open/close cycles.

Symptoms of a bad bracket include:  

• Loose or sagging refrigerator doors that do not close flush  
• Gaps appearing around door seals
• Noises or vibrations emitting from door areas
• Doors difficult to open/close smoothly

As a core mounting component, brackets ensure doors remain firmly and safely attached year after year of use. Replacing a damaged bracket with this OEM part restores a proper secure fit. Compatible also with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

A replacement machine screw with 8-32 threads used to secure panels and components on compatible Whirlpool appliances. Installs quickly to restore proper fit and stop rattling or loose parts. What it does:

• Secures panels, trim, brackets or components that use 8-32 machine-thread fasteners
• Restores proper alignment and prevents vibration-related noise
• Replaces missing, stripped, or damaged screws that allow parts to come loose
• Works where a standard 8-32 machine screw is specified by the manufacturer

• Disconnect power and/or gas before servicing the appliance to reduce shock or injury risk
• Use the proper screwdriver or nut driver for the screw head to avoid stripping
• Thread gently and stop when snug; do not overtighten to prevent stripping or damage
• If threads are damaged, replace with the correct-size screw rather than forcing it

This is a replacement 8-18 threaded screw used to secure panels and components on compatible Whirlpool appliances. It restores proper fastening where a missing or damaged screw causes loose parts or vibration. What it does

• Fastens panels, brackets, and small assemblies to the appliance frame
• Replaces stripped, corroded, or missing screws that cause rattling or loose components
• Helps maintain proper alignment of panels and controls for safer operation
• Suitable where an 8-18 threaded machine screw is specified by the manufacturer

• One replacement screw

• Disconnect power to the appliance before service to prevent shock or injury
• Use the correct driver to avoid stripping the screw head; do not force mismatched tools
• Tighten until snug — avoid over-tightening which can strip threads or crack plastic
• If replacing multiple fasteners, check mating threads and replace any damaged clips or anchors as needed

Color: Black