Lbc22520st-03 Parts

The Toe Grille Clip is an OEM part for LG refrigerators. This part secures the toe grille to the base of the refrigerator, ensuring it remains in place while providing easy access for cleaning and maintenance. 

Causes of a bad Toe Grille Clip can include breakage due to accidental impacts during cleaning or general wear and tear over time. 

Symptoms of a faulty Toe Grille Clip include:

• The toe grille coming loose or falling off
• Difficulty attaching or detaching the grille for routine maintenance
• Visible damage or deformation of the clip
• Unusual gaps between the grille and the refrigerator base

This OEM LG part is also compatible with some Kenmore models.

This display case is the molded housing for the refrigerator's control panel. It supports and aligns the user interface components and trim, restoring a secure, finished fit when the original case is cracked, broken, or out of shape.

• Positions and supports the display/selector board and buttons in the panel opening
• Provides mounting points for panel trim and fasteners
• Helps shield internal components from dust and incidental moisture
• Common signs it's needed: cracked or broken plastic, missing tabs, loose or misaligned control panel

• Unplug the refrigerator before servicing
• Remove the panel/trim per your model's procedure; note screw and clip locations
• Carefully handle the user interface board and wiring; avoid static discharge and pinched harnesses
• Transfer any brackets or clips from the old case to the new one, then reassemble and test

This sheathed defrost heater mounts at the evaporator and melts frost during the automatic defrost cycle to restore airflow and stable temperatures. Replacing a failed heater helps prevent ice-clogged coils, warm spots, and noisy fan interference.

• Melts frost from the evaporator coil during the defrost cycle to maintain proper airflow
• Symptoms of failure: persistent ice on the back panel, weak cooling, or the evaporator fan striking ice
• A failed heater can cause long run times and temperature swings
• Replace if the element tests open/short or shows visible damage

• Disconnect power before service; allow components to warm to reduce risk of cracking brittle plastics
• Remove shelves and the evaporator cover; carefully defrost ice—do not chip or pry against the fins
• Transfer original clips/insulators if present; route wires as original and make firm electrical connections
• After reassembly, ensure the drain area is clear and the fan spins freely

This door gasket assembly forms the airtight seal around your refrigerator door. Replacing a torn or warped gasket restores proper temperature control, reduces frost and condensation, and helps the unit run efficiently.

• Creates a tight seal between the door and cabinet to keep cold air in
• Helps maintain stable temperatures and humidity inside the compartment
• Reduces frost buildup and condensation around the door perimeter
• Common signs it's failing: gaps, tears, hard/warped rubber, condensation, or frequent cycling

• Disconnect power before starting; open the door for access
• Warm the new gasket with hot water or low heat to relax folds—do not overheat
• Remove the old gasket from the retainer/channel; clean the groove thoroughly
• Press the new gasket fully into the channel (loosen retainer screws if present), ensure corners seat, then perform a paper-slip test and allow time for the seal to set

This injection tube routes water to the dispenser/spray assembly to restore proper wash flow and help improve cleaning performance. A direct replacement for damaged or clogged supply tubing in compatible LG appliances. What it does:

• Channels water from the inlet/dispenser area to the spray or dispensing assembly for proper wash cycles.
• Helps maintain correct detergent/water delivery so dishes wash and rinse evenly.
• Prevents bypass flow or misdirection that can reduce cleaning performance.
• Faulty or cracked tubes can contribute to leaks or poor wash results.

• Disconnect power and water supply before starting any repair.
• Remove access panels or kickplate as needed; support the appliance to avoid strain when disconnecting fittings.
• Inspect and replace any worn seals or clamps; seat the tube fully to mating fittings to avoid leaks.
• After installation, restore power/water and run a short cycle to check for proper flow and leaks.

This vegetable tray assembly provides the removable tray used in the refrigerator crisper area to support and separate produce. It restores a stable, easy-to-clean surface so drawers slide and store fruits and vegetables properly. What it does:

• Replaces a cracked, warped or missing crisper tray that supports produce in the refrigerator
• Restores a flat surface so fruits and vegetables sit securely and drawers close properly
• Helps maintain proper airflow and containment in the crisper area for typical produce storage
• Visible damage or a tray that no longer seats can cause items to fall or interfere with drawer operation

• Remove all food and the crisper drawer before installing; work on a clear, protected surface
• Align tray with the existing tracks or guides and slide into place until it seats
• Handle carefully to avoid chips or cracks if the tray is glass or brittle plastic
• Unplug the appliance or disconnect power first and follow all safety precautions

This replacement shelf assembly restores a flat, secure storage surface in the fresh food compartment. It replaces a damaged or missing shelf so items stay organized and supported, seating into the factory rails for a stable, level fit. What it does:

• Provides a level platform for food storage in the refrigerator section
• Fits and locks into the shelf rails/brackets for proper support
• Replaces cracked, broken, sagging, or loose shelves
• Restores lost capacity when a shelf is missing or unsafe to use

• 1 refrigerator shelf assembly

• Unplug the refrigerator and clear items from the shelf area
• Carefully slide the old shelf out of the side rails; retain any hardware reused by your model
• Position the new shelf in the rails; insert the rear edge first, then lower the front until fully seated
• Handle carefully and confirm the shelf sits flat and secure before loading items

This replacement shutter knob snaps onto the refrigerator's vent lever and gives you fingertip control of the air shutter. Restores smooth, accurate vent adjustment so you can fine-tune airflow to the intended compartment.

• Attaches to the shutter/vent lever on a drawer or shelf cover
• Provides manual open/close control of the air passage
• May help fix: broken or missing knob, slider won't engage, vent stuck in one position, hard to adjust temperature in that compartment
• Durable OEM design for a precise, secure fit

• Unplug the refrigerator before servicing
• Remove the drawer or cover if needed for access to the vent lever
• Pull the damaged knob straight off; align the new knob with the keyed lever and press to seat
• Cycle the slider to confirm the shutter opens and closes smoothly before reassembling

This replacement screw secures appliance components in their proper position. Replacing a missing or damaged fastener restores a snug fit, reduces rattling or vibration, and helps keep assemblies aligned for reliable operation.

• Secures panels, brackets, and internal components as specified by your model's parts diagram
• Replaces stripped, rusted, or missing hardware
• Helps address symptoms like rattling/vibration noise, loose panels/trim, or minor misalignment
• Maintains a stable, safe assembly during normal use

• Disconnect power; turn off water and gas supplies if applicable
• Match screw to its original location; do not mix different lengths or types
• Start threads by hand to avoid cross-threading; tighten snugly—do not overtighten
• Follow your model's service/parts diagram for correct placement

This duct assembly routes dryer airflow through the appliance's venting system to help remove hot, moist air during cycles. It restores proper airflow routing so the dryer can vent efficiently and dry loads more reliably. What it does:

• Channels exhaust air from the blower to the external vent or internal ductwork
• Helps prevent moisture buildup and reduces drying times when functioning correctly
• Can reduce hot spots and minimize lint accumulation in the cabinet area
• May eliminate abnormal airflow noises caused by damaged or disconnected ducting

• One duct assembly

• Disconnect power (and gas if applicable) before servicing to avoid shock or fire hazard
• Inspect surrounding seals, clamps and mounting points; replace any damaged hardware for a secure fit
• Use basic hand tools; avoid sharp bends or kinks in the duct to maintain airflow

This door basket replaces a cracked or worn refrigerator door shelf to restore secure storage for bottles and small items. Durable molded plastic keeps contents organized and prevents spills on the door. What it does:

• Provides a stable shelf on the refrigerator door for bottles, condiments and small containers
• Replaces broken, cracked or loose door bins that allow items to fall or shift
• Restores proper alignment so the door closes without obstruction
• Matches OEM fit and mounting locations for a direct replacement

• Remove all food and items from the door before starting
• Lift out the old basket and snap the new basket into the same door track; no cutting or modification required
• Inspect door seals and surrounding trim during installation; handle edges carefully to avoid injury

A replacement access cover that protects internal components and restores the appliance's finished appearance. Installs quickly to shield wiring and assemblies and help reduce noise and wear from exposed openings. What it does:

• Shields internal components from debris and incidental contact
• Helps reduce rattling or vibration caused by damaged or missing panels
• Restores the appliance's finished look after impact or wear
• Used when the original cover is cracked, warped, or missing

• Always unplug the appliance (and shut off water if applicable) before servicing
• Keep original fasteners and follow vehicle/service manual guidance for removal and reinstallation
• Align the cover carefully and secure with the factory screws; do not overtighten

This shelf assembly is a tempered glass storage shelf that provides a flat, stable surface for arranging food and containers in the refrigerator. It restores usable storage space and helps keep items organized and contained. What it does:

• Replaces a cracked, chipped or missing refrigerator shelf to prevent items from falling or spilling.
• Provides a level surface for storing food, pitchers and containers.
• Fits into existing shelf tracks or support clips to lock into position.
• Helps maintain airflow and visibility inside the fresh-food compartment.

• Unplug the refrigerator or switch off power at the breaker before servicing.
• Remove food and supports, then lift the broken shelf straight out, supporting glass to avoid dropping.
• Slide the new shelf into the existing tracks or align with support clips until it seats securely.
• Handle tempered glass carefully and dispose of broken glass per local regulations; wear gloves and eye protection.