Ldc243070st Parts

This is the small trim cap that snaps over the end of a refrigerator door handle. It finishes the handle, covers the mounting hardware, and helps keep the handle secure and looking clean.

• Covers exposed door-handle screws and mounting points
• Restores a finished appearance if the original cap is missing or damaged
• May help reduce handle looseness if the old cap no longer held properly
• Common symptoms: missing end cover, visible handle screws, loose or rattling handle

• Unplug the appliance before starting and open the door for access
• Remove the old cap by gently prying at the seam; avoid scratching the door finish
• Align the new cap with the handle end and press until it snaps fully into place
• If required, tighten handle mounting screws before installing the cap

Restore a sturdy, clean storage surface inside your refrigerator with this replacement drawer tray. It replaces a cracked or missing tray so food stays organized and the drawer fits and functions as intended. What it does:

• Provides the flat base/support for a refrigerator storage drawer
• Helps keep food organized and prevents items from tipping or falling
• Maintains proper fit and alignment of the drawer within the compartment
• Common symptoms: cracks, broken tabs, warping, drawer not sitting level or sliding smoothly

• 1 drawer tray

• Empty and remove the drawer before replacing the tray
• Align and seat the new tray fully in the guides; ensure it is level before reloading
• Transfer any reusable hardware from the old tray if applicable
• Handle plastic carefully to avoid stress cracks; do not force into place

Replacement tray assembly for the fresh food compartment. Restores a flat storage surface and helps contain spills, keeping produce organized and supported in the refrigerator's fresh area. What it does:

• Provides a stable shelf surface in the fresh food compartment for bins and produce.
• Helps contain minor spills and drips, preventing them from spreading to lower compartments.
• Replaces cracked, warped or damaged trays that cause items to tip or slide.
• Restores proper seating/support where a worn tray prevents drawers or bins from aligning.

• Disconnect power to the appliance or unplug the refrigerator before starting any service.
• Typically slides or snaps into place; may be secured with clips or screws depending on model.
• Handle carefully to avoid damage to plastic mounting tabs; inspect mounting points for wear before installing.

This holder is a small mounting bracket that secures a mating component in place inside the appliance. Replacing a cracked or missing holder restores a firm, rattle-free fit and proper alignment.

• Provides a stable mount for the designated part
• Prevents shifting and vibration that can cause noise or premature wear
• Common signs of failure: broken tabs, stress cracks, or the attached part sagging or falling out
• When damaged, the connected component may be loose, noisy, or misaligned

• Disconnect power; if working near water tubing, also shut off the water supply
• Note the original orientation and mounting points; take a photo before removal
• Reuse existing fasteners and avoid overtightening to prevent cracking the plastic
• Ensure the attached component is secure and clears any moving parts before restoring power

This cabinet roller supports the refrigerator and lets the unit roll in and out of place for cleaning or service. Replace a worn or broken roller to restore smooth movement and help keep the appliance properly positioned.

• Supports the base of the refrigerator and enables rolling movement
• Helps with safe positioning and service access without dragging
• Common failure signs: appliance is hard to move, scraping or rolling noises, a flat-spotted/cracked wheel, or a wheel that won't turn
• Replace when the roller is damaged, seized, or missing

• Disconnect power and shut off water supply; protect flooring before moving the appliance
• With help, pull the refrigerator forward and safely support it to access the roller
• Remove mounting fasteners, install the new roller, and reuse original hardware
• Confirm level and smooth movement before returning the unit to its location

This small stopper fits inside the handle assembly to limit travel and keep the handle properly seated. Replacing a worn or missing stopper restores a solid, secure feel when opening and closing your appliance.

• Provides a positive stop for handle movement
• Helps keep the handle aligned and seated against its mounts
• Replaces a cracked, deformed, or missing stopper
• Common signs: handle feels loose or wobbly, over-rotates, or shifts/clicks during use

• Unplug the appliance before servicing to prevent injury
• Support the handle and protect the finish while removing fasteners
• Note the original stopper's orientation and install the new one the same way
• Tighten fasteners evenly; do not overtighten to avoid damaging plastic or finishes

This tray cover creates a level, protective surface over a storage tray or bin inside the appliance. Replacing a cracked or missing cover restores proper support, helps contain spills, and keeps drawers or trays operating smoothly.

• Provides a flat support surface above the tray/bin to hold items
• Helps contain small spills for easier cleanup
• Maintains correct spacing so drawers/trays slide and close properly
• Common failure symptoms: cracked or broken plastic, missing tabs, sagging shelf, drawer not sliding or closing right

• Disconnect power and clear the area around the affected tray
• Remove the tray/bin, then lift out the damaged cover; note orientation and support tabs
• If applicable, transfer any removable components from the old cover
• Seat the new cover fully into the supports and reinstall the tray/bin

This power cord assembly supplies AC power from the wall outlet to your appliance. Replacing a frayed, heat-damaged, or loose cord restores safe, reliable operation and can eliminate intermittent power loss.

• Carries line voltage and ground into the unit to power controls and components
• Routes electricity safely into the cabinet to protect internal wiring
• Replace at the first sign of damage to reduce shock or fire risk

• Disconnect power at the outlet/breaker before servicing
• Compare the new cord to the original; transfer any clips or grommets from the old cord if needed
• Route and secure the cord exactly as original; keep clear of sharp edges and moving parts
• Ensure all connections are fully seated and the ground is properly secured before restoring power

This connector assembly links refrigerator components with a secure, factory-style connection. Replace a damaged or loose connector to restore reliable operation and prevent intermittent performance of the part(s) attached to it. What it does:

• Joins two factory leads/components with a secure locking interface
• Restores a stable connection so the attached component operates reliably
• Helps address intermittent operation, no response, or flickering due to worn or heat-damaged connectors
• Replaces connectors with broken locking tabs, loosened contacts, or visible melting/corrosion

• 1 connector assembly

• Disconnect power before servicing; if working near water lines, also shut off the water supply
• Note connector orientation and routing; take photos to aid reassembly
• Depress the locking tab to release; avoid pulling on wires
• Seat the new connector fully until it locks; route away from sharp edges and moving parts

This factory service kit groups the exact components specified for a model-specific repair. Installing the matched set together restores proper fit and operation while avoiding mismatched parts and repeat trips. What it does:

• Replaces the designated group of parts for the applicable subsystem on your appliance
• Helps resolve improper operation, unusual noise, or visible damage in that area
• Ensures consistent fit and performance with matched factory components
• Supports a single, efficient repair by refreshing related wear items at once

• 1 kit assembly

• Disconnect power; if applicable, turn off water and/or gas before servicing
• Follow your model's service manual and transfer parts one-for-one
• Use appropriate PPE and keep track of screws and small hardware
• Test the appliance fully after reassembly to ensure proper operation

This hinge cover protects and conceals the door hinge area, restoring a clean, finished look and helping keep debris away from the hinge. Replace a cracked, loose, or missing cover to refresh appearance and protect the hinge.

• Conceals exposed hinge hardware for a neat, finished appearance
• Helps shield the hinge area from dust and debris
• Helps prevent snags or rubbing around the hinge during door operation
• Common signs it's needed: cracked or broken plastic, loose/missing cover, cosmetic damage near the hinge

• Disconnect power to the appliance before servicing
• Open the door to access the hinge area; support the door if needed
• Remove the old cover by releasing its clips or screws; retain any fasteners
• Align the new cover and snap or fasten it in place; verify it sits flush and doesn't rub

This center hinge assembly supports the refrigerator door at the mid-cabinet position. It carries the door's weight and provides a smooth pivot so the door aligns properly and the gasket seals as designed to help prevent rubbing and air leaks. What it does:

• Provides the middle pivot and vertical support for a refrigerator door
• Helps maintain door alignment for proper gasket contact and smooth opening/closing
• Wear or damage may cause door sagging, binding/squeaking, gaps, or poor sealing
• Restores correct door positioning after hinge wear or impact

• 1 center hinge assembly

• Disconnect power; protect floors and support the door with a helper
• Remove mounting screws, lift the door off, and take off the old hinge
• Transfer any spacers/shims/bushings from the old hinge if not pre-installed
• Install the new hinge in the same orientation; set door, tighten hardware, and verify alignment and gasket seal

This compressor damper is a vibration-isolating mount that sits between the sealed-system compressor and the chassis. It cushions the compressor to reduce noise, limit vibration transfer, and help keep refrigerant lines from being stressed.

• Isolates the compressor from the frame to absorb start/stop shock and vibration
• Helps reduce humming, rattling, or buzzing from the back/bottom of the appliance
• Replaces a damper that's cracked, flattened, hardened, or missing
• Can help if the compressor rocks or the unit vibrates excessively

• Disconnect power and pull the unit forward for access; remove rear/service panel if present
• Support the compressor to relieve load on the mounts before removing fasteners
• Match orientation; transfer any sleeves/spacers from the old damper to the new one
• Ensure the compressor sits level and that tubing is not strained before restoring power

This fan assembly circulates air through the appliance so coils and internal components operate at the proper temperature. Replacing a failed or noisy fan can restore airflow and help prevent performance issues caused by weak circulation.

• Moves air across coils and components to support designed cooling/dehumidifying performance
• Helps maintain steady airflow to reduce overheating or icing conditions
• A failing fan can cause little to no airflow even when the unit is running
• Common symptoms: fan not spinning, intermittent operation, loud rattling/grinding, vibration, or thermal shutdown

• Disconnect power before servicing to avoid electrical shock or injury
• Access the fan area per your unit's service information; remove panels/shrouds as needed
• Note wire connections and mounting order; transfer any brackets, grommets, or hardware from the old assembly
• After installation, ensure the fan spins freely and clears all shrouds, then test operation before reassembly

This name plate is the exterior emblem that mounts to the appliance's front panel. It replaces a missing, cracked, or faded badge to restore a clean, factory look and cover the designated trim area.

• Attaches to the outer panel to display brand/series identification
• Restores a finished appearance where the original emblem sits
• Direct replacement for a lost, damaged, or worn badge
• Typical symptoms: missing emblem, loose or broken tabs, peeling, or discoloration

• Disconnect power before servicing the appliance
• Carefully remove the old emblem; release any tabs from behind or peel away remaining adhesive
• Clean and dry the mounting surface; remove all residue for best fit
• Align with the recess/holes and press evenly until fully seated

This sheath heater is the heating element used in compatible electric dryers to generate hot air for drying. Replaces a worn or failed heater element to restore normal drying performance and reduce extended dry times. What it does:

• Heats air inside the dryer cabinet so clothes can dry efficiently.
• Commonly linked to symptoms like clothes not drying, extended drying cycles, or no heat from the dryer.
• Works with the dryer's thermostats and thermal fuses; a faulty heater can mimic other heat-related failures.

• Disconnect power at the breaker before servicing — this part involves live AC voltage.
• Inspect and replace any open thermal fuses or failed thermostats at the same time as recommended by the model service guide.
• Handle the element carefully to avoid bending or damaging the sheath; follow OEM instructions and torque specs during reassembly.