Ldc243070st Parts

This door gasket assembly creates the airtight seal around a refrigerator door to help maintain proper temperature and reduce energy loss. It replaces a worn or damaged seal to help keep food fresher and reduce moisture buildup. What it does:

• Seals the door to prevent warm air from entering the cabinet
• Helps maintain consistent internal temperature and cooling performance
• Reduces frost or condensation caused by a leaking seal
• Can stop drafts, rattling doors, and excessive run-time tied to a bad seal

• One door gasket assembly

• Disconnect power to the refrigerator before starting any repairs
• Remove the old gasket and clean the door frame before installing the new seal
• Press the gasket into the channel and secure per manufacturer clips/screws; warm the gasket slightly if needed for easier positioning
• After installation, check the seal around the full perimeter and adjust or retorque fasteners as required

A replacement glide rail assembly that supports and guides a refrigerator/freezer drawer for smooth opening and closing. Restores proper drawer tracking and helps prevent sticking or misalignment. What it does:

• Provides the rail and mounting components that the drawer slides on for stable operation
• Restores smooth drawer movement and alignment when original rail is bent or worn
• Helps reduce drawer sticking, scraping, or uneven travel
• Intended for use where the OEM glide/rail assembly is specified

• One glide rail assembly

• Follow the appliance manufacturer's service manual for removal and installation steps
• Disconnect power and empty the drawer before working to prevent injury or damage
• Inspect mounting hardware and drawer slides; replace any damaged fasteners
• Use basic hand tools;

This guide assembly rail replaces a worn or damaged drawer slide to restore smooth, stable drawer movement and proper alignment. It helps reduce sticking, misalignment, and rattling for a secure fit and quiet operation. What it does:

• Guides and supports the drawer or compartment during open/close cycles
• Restores smooth sliding action and consistent alignment
• Reduces noise caused by worn or bent rails or guides
• Helps prevent drawers from catching or binding

• Disconnect power and empty the drawer before beginning service
• Removal of the drawer and access panel may be required; keep fasteners for reassembly
• Align the rail before tightening fasteners; use basic hand tools

This hinge cap protects and covers the refrigerator door hinge, keeping the hinge area clean and helping the door operate smoothly. A small replacement that restores a finished look and prevents debris from entering the hinge. What it does:

• Covers the exposed hinge to protect it from dirt, dust, and spills
• Helps maintain proper door alignment by keeping hinge components shielded
• Stops cosmetic damage to the hinge area and improves appearance
• Reduces hinge noise caused by debris in the hinge pocket

• High-level, safety-first: unplug or disconnect power to the appliance before servicing if work may contact electrical components
• Support the door or have a helper when removing or reinstalling hinge-related parts to prevent dropping or misalignment
• Use basic hand tools as needed; avoid forcing parts—inspect mating surfaces before reinstalling the cap
• If hinge damage or significant wear is present, replace the entire hinge assembly rather than only the cap

This replacement door shelf bar secures items on a refrigerator door shelf, restoring proper storage and helping keep bottles and containers from sliding or falling when the door is opened. A simple, direct fix for broken or missing shelf retainers. What it does

• Holds door-bin items in place so bottles, jars and containers stay secure during normal use
• Replaces cracked, warped or missing shelf retainer bars that allow items to tip or fall
• Helps restore proper shelf function and usable door storage
• Designed to match the OEM fit and mounting points for a direct replacement

• Remove contents from the door shelf before replacing the bar
• Install by aligning with the shelf slots or mounting tabs and snapping or sliding into place per the original orientation
• Use gentle pressure to avoid damaging surrounding bins or trim; do not force metal parts
• Refer to your refrigerator's owner's manual for model-specific instructions and safety guidance

This decor tray is a cosmetic trim panel designed to restore the appliance's exterior appearance and cover the underlying frame. It replaces a scratched, dented, or missing trim piece to give the unit a clean, finished look. What it does

• Restores the appliance's exterior appearance by covering damaged or worn trim areas
• Protects underlying components from incidental contact and debris
• Helps maintain a uniform finish across the front/side where installed
• Suitable when the existing trim is bent, cracked, or cosmetically worn

• Disconnect power to the appliance before beginning any service
• Typically secures with clips or screws; keep fasteners and mounting orientation noted for reassembly
• Handle carefully to avoid scratching the finish during installation

This door gasket assembly seals the refrigerator/freezer door to help keep cold air in and improve cooling efficiency. It replaces a worn or damaged seal to reduce leaks and help maintain proper temperature control. What it does:

• Creates an airtight seal around the door to limit cold-air loss and reduce frosting
• Helps the appliance maintain consistent internal temperature for food safety
• Reduces energy loss caused by gaps or torn seals
• Commonly used when the existing gasket is torn, warped, or no longer seals properly

• One door gasket assembly

• Inspect the door flange and gasket channel for debris; clean before installing
• Gaskets typically stretch into a groove or secure with retainer tabs—follow OEM steps
• Replace with power off and remove any shelf items that obstruct door access

This service PCB power control board is the appliance's main onboard power and control module, restoring reliable power distribution and control logic so the appliance can start and respond to inputs properly. What it does:

• Regulates and distributes power to key circuits and components
• Manages startup and control logic for normal operation
• Interfaces with user controls and sensors to process commands
• Can resolve symptoms like no power, blank display, or unresponsive controls
• Helps clear intermittent power loss and erratic behavior when board failure is the cause

• Disconnect power before beginning and verify the appliance is de-energized
• Take photos of wiring and connector positions before removal to ensure correct reassembly
• Handle the board carefully and avoid electrostatic discharge (ESD) to prevent damage
• After installation, restore power and verify normal operation and that prior symptoms are resolved

This genuine replacement knob shutter restores the control panel's knob opening and protects internal switches from debris while allowing knobs to engage properly. It helps maintain smooth knob operation and reduces dirt buildup behind the control surface. What it does:

• Covers the knob opening and guides the control knob into place for reliable engagement
• Protects internal switches and electronics from dust, crumbs, and spills
• Helps prevent accidental knob movement when not in use
• Restores proper fit and appearance of the control panel area

• One knob shutter

• Power off and unplug the appliance before beginning any work to avoid electrical shock
• Small fasteners or clips may need to be removed; use appropriate hand tools and keep track of hardware

This drawer guide is the replacement rail that helps a freezer or refrigerator drawer open and close smoothly, restoring proper alignment and reducing sticking or grinding during use. Designed to match OEM fit and function. What it does:

• Guides the drawer along its track to ensure smooth, even movement
• Keeps the drawer aligned to prevent binding, rubbing, or tipping
• Reduces noise from scraping or catching when opening or closing
• Helps restore proper drawer seating and overall compartment accessibility

• One drawer guide (rail) as shown

• Inspect mating track and adjacent hardware for damage before installing
• Remove power or follow manufacturer safety guidance for accessing interior components
• Install with original fasteners; tighten securely but avoid over-torquing
• If multiple guides are worn or damaged, replace matching guides on the other side for best performance