Leq01442eso Parts

This cable tie secures wiring and the power cord to the appliance chassis to help prevent chafing, pinching, or loose connections. Simple, low-cost part that restores proper wire routing and strain relief. What it does

• Holds wiring and harnesses in place to prevent rubbing against sharp edges
• Helps reduce risk of intermittent power or connector strain caused by loose wires
• Keeps harnesses routed for correct clearance and component access
• Useful during repairs to restore original wire routing and strain relief

• One cable tie (wire harness retainer)

• Safety first: disconnect the appliance from power before inspecting or replacing wiring components
• Remove the damaged or existing retainer and route harnesses to match original OEM routing before installing the new tie
• Trim excess tie tail; do not overtighten—secure, but avoid crushing wires
• Replace any tie that's melted, cracked, or otherwise damaged rather than reusing it

This push-to-start knob replaces a worn, loose, or damaged start control on compatible Whirlpool console controls, restoring a positive push feel and reliable user interface to the appliance. What it does:

• Engages the dryer/washer start mechanism when pressed, providing tactile control for cycle start.
• Replaces cracked, faded, or stuck knobs that are hard to press or don't seat properly.
• Helps correct a knob that spins freely or has worn splines and won't activate the switch.
• Restores original appearance on consoles with a gray finish.

• Disconnect power to the appliance before servicing to avoid electrical shock.
• Pull the old knob straight off the control shaft; align splines and press the new knob fully onto the shaft.
• If access requires removing the control panel, keep and replace all fasteners and gaskets as found.
• Do not force the knob; if resistance is felt, verify alignment to avoid damaging the splines or switch.

This exhaust pipe directs heated air from the dryer drum to the household vent, restoring proper airflow for efficient drying and reduced lint buildup. It's a direct-fit replacement designed to match the OEM airflow path. What it does:

• Channels dryer exhaust from the appliance to the external vent to maintain proper airflow.
• Helps prevent lint accumulation in the cabinet by providing a sealed exhaust path.
• Can reduce long dry times and overheating caused by restricted or damaged venting.
• Addresses symptoms such as poor drying performance, hot dryer cabinet, or noticeable burning/overheating smells near the dryer vent area.

• One exhaust pipe.

• Disconnect power (and gas, if applicable) before starting work; the appliance is fully de-energized.
• Wear gloves to avoid sharp edges; remove old pipe and clean vent connections before installing the replacement.
• Secure with appropriate clamps or fasteners and ensure a continuous, unobstructed path to the exterior vent.
• After installation, run a short cycle to check for leaks.

This mounting bracket secures internal components in place to keep appliance parts aligned and stable during normal use. Replacing a damaged bracket restores proper fit and support for affected assemblies. What it does:

• Provides structural support for internal panels or assemblies to prevent shifting and noise
• Helps maintain proper alignment of moving parts to reduce wear
• Stops rattling or vibration caused by a broken or bent bracket
• Keeps connected components securely attached after repair or reassembly

• One mounting bracket

• Disconnect power and water before starting any repair
• Inspect surrounding fasteners and hardware; replace any stripped screws for a secure fit
• Use proper-size tools to avoid damage to mounting holes or nearby components

This replacement plug seals and covers an appliance opening to keep out water, dirt and debris and to protect internal components. It restores a finished appearance and helps maintain safe, reliable operation. What it does:

• Seals service or access openings to prevent moisture and debris intrusion
• Covers unused ports or cutouts for a clean, finished look
• Helps protect wiring and internal parts from contamination
• Prevents drafts that can affect temperature-sensitive compartments

• Always disconnect power before accessing appliance internals
• Press-fit or snap-in design — align and push into place until fully seated
• Inspect surrounding area for damage; replace if plug is torn or brittle