Lfc20786sw Parts

This center hinge assembly supports and pivots the middle door section to keep doors aligned and operating smoothly. Replace a worn or damaged center hinge to restore proper door movement and help maintain a tight seal. What it does:

• Provides the pivot point and structural support for the center door section to open and close smoothly
• Helps maintain door alignment to prevent rubbing, scraping, or uneven gaps
• Reduces door sag that can interfere with sealing and cooling efficiency
• Prevents binding or sticking during door operation

• One center hinge assembly

• Disconnect power to the appliance before starting any repair
• Doors are heavy—have a second person assist to support doors while removing or installing the hinge
• Remove any trim or covers to access hinge screws; align doors fully before tightening fasteners
• Use manufacturer-recommended torque; do not overtighten screws or force parts into place

This main control PCB manages appliance functions and user interface signals so the unit runs as designed. Replace a failed board to restore normal control and communication between sensors, buttons, and motors. What it does:

• Routes power and control signals to major components for coordinated operation
• Interprets user inputs from the control panel and sends commands to actuators
• Communicates with sensors and other modules to regulate cycles and functions
• Can cause symptoms such as unresponsive controls, error codes, failure to start, or erratic operation when defective

• Disconnect all power before beginning service to avoid shock or damage
• Take photos or label wiring and connectors to ensure correct reassembly
• Handle the board by its edges and avoid touching components or contacts to prevent static damage

This door gasket assembly seals the refrigerator door to help maintain proper temperature and reduce energy loss. It replaces a worn or damaged seal to help keep food fresher and prevent moisture or frost buildup. What it does:

• Creates an airtight seal around the refrigerator door to reduce cold air loss
• Helps prevent moisture, frost, and condensation inside the compartment
• Restores proper door sealing when the original gasket is torn, deformed, or hardened
• Can reduce compressor run-time caused by a leaking door seal

• One complete door gasket assembly

• Unplug the appliance or switch off power before starting any repair
• Remove the door liner or trim as required by your model to access the gasket; follow OEM instructions
• Clean the gasket channel and surrounding area before installing the new seal for best fit

This shelf net is a mesh-style refrigerator shelf designed to support and contain food items while allowing airflow. It replaces torn, stretched, or missing nets to restore storage organization and help prevent items from shifting. What it does:

• Provides a flexible, ventilated surface for storing packaged foods, produce, or deli items
• Helps keep small or irregularly shaped items from falling through larger shelves
• Restores proper storage function when original netting is damaged, loose, or missing
• Compatible with designated shelf frames and snaps into place where equipped

• Unplug the appliance or turn off power to the unit before servicing for safety.
• Empty and remove food items from the affected shelf area before installation.
• Install by aligning the net with the shelf frame and securing per the owner's manual; do not force or modify parts.
• If installation requires removal of shelves or trim, keep fasteners and small parts organized and follow manufacturer instructions.

This replacement guide provides a secure mounting surface to keep the appliance component aligned and operating smoothly. It restores proper fit and reduces rubbing or binding caused by a worn or broken guide. What it does

• Positions and supports the associated component to prevent misalignment and excessive movement
• Reduces scraping, rubbing, or grinding noises caused by a damaged guide
• Helps drawers, doors, or internal assemblies slide and seat correctly
• Restores smooth operation when original guide is cracked, worn, or missing

• One replacement guide

• Disconnect power (and water, if applicable) before starting any repair
• Minimal hand tools are typically required; follow the appliance service manual for exact steps
• Inspect surrounding clips, screws, and tracks; replace any damaged hardware for best results

This drip tray catches and channels defrost and condensation water under the appliance to prevent pooling and water damage. It's a direct-fit replacement that restores proper drain flow and reduces leaks. What it does

• Collects defrost and condensation water from the evaporator area so it drains to the evaporation area or drain.
• Helps prevent water pooling beneath the appliance that can cause floor damage or mildew.
• Restores proper routing of meltwater after ice or defrost cycles.
• Use when the original tray is cracked, warped, clogged, or missing.

• One drip tray

• Disconnect power to the appliance before starting any repair to avoid shock.
• Access typically requires removing lower access panels or pulling the appliance away from the wall; follow your model's service instructions.
• Inspect and clear the drain tube and surrounding area while replacing the tray to ensure proper drainage.

This relay cover is a protective housing that shields a washer or dryer relay assembly from dust, moisture, and accidental contact, helping maintain safe and reliable operation of the appliance's control components. What it does:

• Protects the relay and nearby wiring from debris and moisture that can cause shorts or corrosion
• Helps prevent accidental contact with relay terminals during maintenance
• Reduces risk of electrical arcing or damage when relays switch under load
• Can improve long-term reliability of the control assembly when installed and intact

• Disconnect power to the appliance before servicing to avoid electrical shock
• Remove access panels as needed to reach the relay area; basic hand tools typically required
• Handle control board and components carefully to avoid damage from electrostatic discharge
• Replace only with the specified cover; do not modify or force-fit

This outer housing cover protects internal components and gives the appliance a finished appearance. It replaces a cracked, damaged, or missing panel to restore protection and reduce rattling. What it does

• Shields motors, controls, and wiring from dust and debris
• Prevents foreign objects from contacting internal parts
• Reduces vibration noise caused by loose or broken panels
• Restores the appliance's exterior fit and finish

• One outer housing cover

• Disconnect power to the appliance before starting any work
• Remove any trim, screws, or clips holding the old cover in place; keep fasteners for reassembly
• Handle the cover carefully to avoid scratching the finish or damaging mounting tabs
• Replace any broken clips or fasteners before finishing installation

This decorative control panel covers and protects the appliance's user controls while giving the console a finished appearance. It restores the look and button access so you can see and press the controls normally. What it does:

• Replaces a cracked, faded, or damaged decorative panel that surrounds the control buttons
• Restores proper button labeling and tactile surface for reliable user input
• Helps protect the underlying control board and switch assembly from spills and wear
• Reduces light bleed or obscured buttons from cosmetic damage

• Disconnect power before beginning any repair to avoid shock or damage
• Removal typically requires opening the console and removing fasteners; keep track of screws and clips
• Handle edges and buttons gently to avoid scratching or bending the panel
• Inspect connectors and underlying components while installing; do not force the panel into place