Lfc24770sw Parts

This motor support damper sits between the refrigerator's compressor and base to absorb vibration and movement. Replacing a worn damper helps quiet rattles and humming from the back of the cabinet and keeps the compressor properly supported.

• Cushions the compressor to reduce transmitted vibration and noise
• Helps quiet humming, buzzing, or rattling from the lower rear of the refrigerator
• Maintains proper compressor alignment and support on the base pan
• Common signs of wear: increased vibration/noise, a cracked or flattened damper, or noticeable compressor movement when running

• Unplug the refrigerator and pull it forward to access the rear; allow the compressor to cool before working
• Support the compressor to remove load from the mount before loosening hardware
• Replace the damper and tighten mounting hardware evenly without over-compressing the rubber
• Avoid bending or stressing refrigerant tubing; wear gloves and eye protection

This hinge cover is a cosmetic and protective trim piece that snaps over the door hinge to hide hardware and protect the hinge area from dust and damage. It restores the finished look and helps keep the hinge area cleaner. What it does:

• Covers and protects the door hinge hardware from dust, spills, and everyday wear
• Conceals exposed screws and components for a finished appearance
• Reduces chance of items catching on the hinge area and causing damage
• Helps stop light rattles or vibration noise caused by loose or damaged trim

• Install by snapping the cover over the hinge; may require lightly prying off the old cover first
• Inspect hinge screws and hinge pin; tighten if loose before installing the cover
• Use basic hand tools; disconnect power only if you will be working near electrical components
• If cover is cracked or broken, replace to avoid interference with door operation

This replacement door gasket assembly seals the refrigerator door to help maintain proper temperature and reduce energy loss. It restores the seal around the door edge for better cooling performance and food preservation. What it does:

• Creates an airtight seal around the refrigerator door to limit cold air escape
• Helps maintain consistent internal temperature for food safety
• Reduces frost buildup and excessive compressor run time when working properly
• Addresses symptoms such as warm spots near the door, visible gaps, or persistent condensation

• One door gasket assembly

• Inspect the door and mounting channel for debris before installing; clean with mild detergent and dry completely
• Gasket typically stretches into a channel and secures around the door perimeter—avoid sharp tools that can damage the seal
• For best results, install at room temperature; warm the gasket gently if needed to ease fitting

This replacement door basket mounts on the refrigerator door to hold bottles, jars, and condiments. It restores secure, easy-access storage when the original bin is cracked, damaged, or missing.

• Attaches to the inner door rails to organize items on the door
• Keeps contents in place as the door opens and closes
• Replaces a cracked, broken, warped, or missing bin
• Symptoms include broken tabs, bin won't stay seated, or reduced door storage

• Remove items from the old bin; lift up to release it from the door rails
• Align the new basket's hooks with the door slots and lower until fully seated
• Confirm the bin is level and secure before loading
• No tools typically required; avoid overloading to prevent damage

This door gasket assembly replaces a worn or damaged refrigerator door seal to restore a tight enclosure and help maintain consistent cooling. It provides a new pliable sealing surface that reduces air leaks and helps prevent frost or moisture buildup. What it does:

• Creates a full seal around the refrigerator door to minimize cold air loss and warm air intrusion.
• Helps reduce frost buildup, water pooling, and excessive compressor run time caused by a leaking seal.
• Restores proper door contact when the original gasket is torn, deformed, or no longer magnetically sealing.
• Improves temperature stability for better food preservation and energy efficiency.

• One door gasket assembly

• Disconnect power to the appliance before starting and follow manufacturer safety guidelines.
• Inspect and clean the gasket channel and door surface before installing the new seal for best fit.
• Align the gasket into the channel and press evenly; some models may require loosening the door or removing trim for access.

This hinge cover protects and conceals the washer's lid hinge assembly for a clean look and safer operation. It helps keep debris out of the hinge and restores the cabinet appearance after damage. What it does:

• Covers the lid hinge to protect internal hinge components from dirt and damage
• Conceals exposed hardware for improved appearance and user safety
• Restores smooth lid operation when original cover is cracked, broken, or missing
• Reduces rattling and contact between the lid and hinge area

• Disconnect power to the appliance before starting any repair
• Remove any screws or clips securing the old cover and gently snap or slide the replacement into place
• Use basic hand tools; keep small hardware organized for reassembly
• If hinge hardware is damaged or binding, inspect and replace those parts as needed for proper operation

This door gasket assembly replaces a worn or damaged refrigerator door seal to restore an airtight closure and help maintain proper cooling. It fits the door's perimeter and creates the seal between the cabinet and door. What it does:

• Seals the refrigerator door to retain cold air and improve temperature stability.
• Prevents warm air intrusion that can cause frost buildup or increased energy use.
• Helps reduce condensation and water leaks around the door area.
• Restores proper door alignment and closing when old gasket is torn, stretched, or deformed.

• Unplug the appliance and remove food from the door area before starting.
• Work with the door propped or supported; follow OEM removal steps for existing gasket tabs or clips.
• Gently warm and flex the new gasket if needed for easier seating; avoid sharp tools that can puncture it.
• After installation, check the seal around the full perimeter and allow a short run cycle to verify proper operation.

This Tray Assembly is the replacement vegetable-drawer pan that holds produce and helps contain spills inside the fridge. Restores a secure storage surface so fruits and vegetables sit level and are easier to organize. What it does:

• Replaces a cracked, warped or broken vegetable drawer pan that no longer supports produce
• Contains leaks and small spills to help keep the refrigerator interior cleaner
• Provides a stable base for crisper/vegetable drawers to slide and sit properly
• Helps restore proper drawer alignment and prevents items from falling through gaps

• Remove fresh food and open/slide out the affected drawer; lift to disengage and remove the old pan
• Align new tray with drawer rails and slide in until it seats; verify smooth operation before loading
• Handle glass or brittle plastics with care to avoid chips or cracks during installation

This hinge assembly replaces a worn or damaged refrigerator door hinge to restore proper door alignment and smooth opening and closing. It helps stop sagging doors, noisy movement, and improper sealing for better cooling performance. What it does:

• Supports and pivots the refrigerator door for correct alignment and even sealing
• Replaces broken, bent, or worn hinge hardware that causes door sag or misalignment
• Reduces rubbing, grinding, or noisy hinge movement when opening or closing
• Helps restore proper door closure to prevent cold air loss and temperature issues

• Unplug the appliance and support the door before removing hinge hardware to prevent injury or damage
• Transfer any mounting screws or brackets only if specified by the OEM; replace visibly damaged fasteners
• Tighten mounting fasteners to secure the hinge but avoid over-torquing; confirm door alignment after installation

A small protective cap that covers and protects a component connection or opening from dirt and moisture, helping maintain proper function and prolong component life. Simple replacement when the original cap is cracked, missing, or worn. What it does:

• Covers exposed fittings, terminals, or openings to keep out debris and moisture
• Helps prevent leaks or contamination at the sealed connection
• Restores a secure fit when the original cap is cracked, split, or degraded
• Commonly used where a small, removable protective seal is required

• Inspect mating surface and surrounding gasket/seal before installing; replace other damaged parts as needed
• Press the cap firmly into place until fully seated; no special tools usually required
• Wear gloves and disconnect power or water supply if working near energized or pressurized components

This cover assembly protects the appliance's printed circuit board from debris, moisture and accidental contact, helping preserve reliable control operation. It provides a secure enclosure that keeps the PCB mounted and shielded during normal use. What it does:

• Shields the control board from dust, moisture splash and foreign objects that can cause shorts or component damage.
• Keeps wiring and connectors routed and secured to reduce strain and intermittent connections.
• Helps maintain correct spacing and alignment of the PCB for reliable electrical contacts.
• Useful when the original plastic cover is cracked, warped, missing or allows board exposure.

• One cover assembly for PCB.

• Disconnect power to the appliance before beginning any service to avoid shock or damage.
• Handle the PCB and connectors carefully; avoid touching board components or bending traces.
• Align cover over the PCB and fasten with the original screws or clips; do not overtighten plastic fasteners.