Lfns22520s Parts

This balance ring assembly helps stabilize the washer tub and reduce vibration and excessive movement during spin cycles. Replacing a worn or damaged balance ring restores quieter, more even operation. What it does:

• Cushions and balances the outer tub to reduce vibration and rocking during spin
• Helps prevent loud banging or thumping noises caused by an unbalanced load
• Reduces wear on suspension components by keeping the tub properly centered
• Contributes to smoother spin performance and more consistent draining

• Disconnect power and water before beginning any repairs
• Handle tub components carefully—use proper supports to prevent the tub from shifting or falling

This door seal assembly creates a tight, durable seal around the appliance door to help keep heat and air inside the cabinet for efficient operation and consistent drying. It replaces a worn or damaged seal to restore proper door closure. What it does:

• Seals the gap between the door and cabinet to reduce air and heat loss
• Helps maintain consistent drying performance and cycle efficiency
• Prevents lint, moisture, and debris from escaping the drum area
• Reduces door-edge rubbing that can cause fabric wear or damage

• Disconnect power to the appliance before beginning any work.
• Inspect the door opening and gasket mating surface; clean away lint or residue before installing.
• Ensure correct seal orientation and full seating around the door perimeter; use existing clips/screws if applicable.
• After installation, run a short test cycle to verify the door closes properly and there are no leaks.

This flow output control assembly routes 120 VAC power to the washer's flow/valve circuits so the machine can control water flow during cycles. It replaces a failed output module to restore proper electrical control of water-related functions. What it does

• Switches 120 VAC power to water flow/valve circuits under controller command
• Helps restore normal water fill and drain sequencing when the output is faulty
• Common symptom: washer fails to energize valves or show flow-related errors
• Works as the electrical output stage tied to the machine's flow control system

• One flow output control assembly (120 VAC)

• Disconnect power before servicing to avoid shock or damage
• Handle the assembly carefully; avoid bending pins or stressing connectors
• Confirm connector orientation and secure mounting before reapplying power

This replacement rubber foot cushions the machine's contact point with the floor to improve stability, reduce vibration, and protect surfaces. Replace a worn or missing foot to restore steadier, quieter operation and easier leveling.

• Provides a cushioned, non-slip contact point between the appliance and floor
• Helps absorb vibration and reduce rattling or movement during cycles
• Aids in proper leveling and overall stability
• Replace when cracked, flattened, or missing, or if the unit rocks or "walks"

• Disconnect power; for washers, also turn off water. If applicable, shut off gas supply
• Carefully tilt or raise the appliance with assistance and proper lifting support
• Remove the worn foot and install the new foot on the leveling leg or base as designed, ensuring it seats fully
• Re-level the appliance and tighten any locknuts; verify stable operation

A specialized service wrench designed for Horizon/TL-L style Speed Queen machines to aid technicians during maintenance. Provides a secure grip for installing and removing the specific service fasteners used on these transmissions and hubs. What it does:

• Fits the Horizon/TL-L service fastener to allow controlled tightening or loosening
• Speeds routine service tasks that require the OEM service wrench
• Reduces risk of damaging the fastener when compared with improvised tools
• Useful for maintenance and repair work performed on transmission/hub assemblies

• One Horizon/TL-L service wrench

• Intended for qualified service technicians familiar with Speed Queen equipment
• Disconnect power and follow all safety procedures before servicing
• Use the tool only for its intended fastener; do not use as a pry bar or hammer
• Inspect the tool before use; replace if damaged

This pressure sensor assembly detects water pressure to monitor and control washer water level, helping the machine fill and drain correctly. Replaces a failed pressure sensor to restore accurate fill sensing and cycle operation. What it does:

• Senses tub water pressure and signals the control to start/stop filling
• Helps prevent overfill or underfill conditions when functioning correctly
• Commonly replaced for symptoms like incorrect water level, continuous filling, or fill/drain errors
• Works with the washer's air line/tub pressure system to report water level

• Disconnect power and turn off water supply before beginning service
• Note tubing routing and electrical connector orientation; photograph before removal
• Handle sensor and vacuum/air line gently to avoid kinks or damage
• Test washer through a short cycle after install to confirm correct operation

This drawer dispenser assembly replaces a worn or damaged detergent drawer and restores reliable detergent and additive delivery for top-load laundry machines. It helps keep detergent flowing into the wash and prevents leaks from a broken drawer. What it does:

• Provides a proper chute and housing for detergent and fabric softener to enter the wash tub
• Replaces cracked, jammed, or missing dispenser drawer components that cause leaks or improper dispensing
• Ensures smoother drawer operation and correct alignment with the dispenser housing
• Helps prevent detergent buildup and improves delivery timing during the wash cycle

• One complete drawer dispenser assembly

• Follow the washer manufacturer's service manual or IPL for disassembly and reassembly steps
• Disconnect power and water supply before servicing to avoid shock or flooding
• Inspect surrounding seals and dispenser housing for damage; replace if necessary

A replacement self-tapping pan-head screw sized 10 x 5/8 in for securing appliance panels, trim and small assemblies. Restores proper fastening where original screws are missing, stripped or corroded. What it does

• Cuts its own mating thread in sheet metal or plastic for secure fastening
• Commonly used to attach control panels, trim pieces and small brackets
• Helps stop rattles, loose panels and misaligned trim when original fasteners fail
• Corrosion-resistant finish resists rust in typical laundry appliance environments

• Use the correctly sized screwdriver or driver bit to avoid stripping the head
• Start in a pilot hole if material is brittle or if reinstalling into worn threads
• Do not over-torque; stop when the head seats flush to avoid cracking or stripping
• Disconnect power and follow appliance-specific safety procedures before working

This hex washer-head screw secures panels and components in commercial washers and dryers, providing a low-profile, vibration-resistant fastener that helps keep assemblies tight and aligned during operation. What it does:

• Fastens sheet metal and plastic parts where a wide bearing surface is needed
• Hex washer head spreads load to reduce pull-through on soft materials
• Self-tapping thread cuts into mating material for a secure fit without a nut
• Commonly used where vibration and repeated motion can loosen standard screws

• Use the correct size driver or socket to avoid stripping the head
• Start the screw straight and apply steady pressure while driving to ensure proper thread engagement
• Tighten until snug — avoid over-torquing which can strip threads or crack panels
• Disconnect power and follow all safety precautions before servicing appliance

This hex head machine screw fastens appliance panels and components, restoring secure assembly and stopping movement or vibration. It's a simple replacement when original screws are lost or worn. What it does:

• Secures panels, brackets, and internal components to prevent rattling or misalignment
• Replaces missing or damaged screw heads that keep parts firmly attached
• Restores proper fit where stripped or corroded fasteners allow play
• Helps maintain safe operation by keeping covers and guards in place

• Disconnect power and water before working on the appliance
• Use the matching hex driver or socket to avoid rounding the head
• Replace like-for-like; tighten until snug but avoid over-torquing
• If threads are damaged, inspect mating part and replace as needed

This top cover weldment is the factory replacement panel that supports and protects the washer's upper cabinet area, restoring a secure, finished top surface and preventing damage to internal components. Ideal for repairing loose, bent, or damaged tops. What it does

• Replaces the welded lower section of the top cover assembly to restore structural support and proper fit.
• Protects internal components and wiring from debris and accidental contact.
• Helps stop rattling or movement caused by a damaged or warped top panel.
• Restores the cabinet surface for proper sealing and alignment with other panels.

• Disconnect power before starting any repair to avoid shock or injury.
• Basic disassembly of the cabinet top and removal of mounting fasteners required; follow OEM service manual for steps.
• Handle edges carefully — metal panels and weldments can have sharp edges.
• Reuse or replace any fasteners/clips as needed to ensure a secure fit and proper alignment.

This Micro-V (multi-rib) drive belt transfers motor power to the machine's drive system so the tub/drum turns smoothly. Replacing a worn or broken belt restores consistent tumble/spin and reduces slippage, squealing, and burning-rubber odors.

• Transfers motor rotation to the drive pulley to turn the tub/drum
• Maintains traction across ribbed pulleys to minimize slipping under load
• Common failure symptoms: no tumble/spin, intermittent movement, squealing/chirping, or rubber smell
• Visual clues of wear: cracking, glazing, frayed ribs, or excessive stretch

• Disconnect power; shut off water and gas before servicing
• Note belt routing before removal; route over motor, idler/tensioner, and drive pulley
• Inspect idler, tensioner, and pulleys for wear or rough bearings and replace as needed
• After installation, hand-rotate to check tracking and alignment; run a short test cycle to verify operation

This complete white door assembly replaces a damaged or worn dryer door to restore a proper seal and smooth opening. Designed for machines with a right-side hinge, it provides a ready-to-install replacement to get the door working correctly. What it does:

• Replaces the dryer door and right-side hinge to restore proper door swing and closure
• Helps reestablish a secure front seal for efficient drying and consistent tumbling
• Addresses common symptoms like a loose, sagging, or non-closing door
• Prevents further wear to the cabinet edge and latch by restoring correct alignment

• Disconnect power before beginning any repair and work with the dryer empty and cool
• Some models may require removal of the front panel for access; keep hardware organized
• Handle glass and painted surfaces carefully to avoid scratches; two people may be helpful for alignment
• Verify hinge orientation and latch engagement before final tightening

Note: This part includes one shock with instructions.

The Shock Assembly Kit is an OEM part for Speed Queen washing machines. It is a comprehensive kit that includes one shock absorber and the necessary mounting hardware. This shock absorber plays a vital role in absorbing shocks and vibration during the spin cycle.

Symptoms of a bad shock absorber include:

• Excessive shaking or vibrating during operation  
• Loud banging noises occurring during spinning
• The washer moving or walking on the floor during use
• Leaks developing due to added stress on components

Causes of a bad shock absorber can include wear and tear over time, exposure to heavy loads that strain the system, or damage due to impact. 

This OEM replacement is also compatible with Whirlpool, Maytag, Amana, Roper, and some Kenmore models. With its durable design and tight fittings, the Shock Assembly effectively minimizes machine movement to reduce noise and protect components.

This 1 HP SVI control assembly is the drive/control module that manages motor speed and wash/dry cycles for compatible commercial washers. It replaces a worn or failed control to restore proper motor and drive operation. What it does

• Controls motor power delivery and speed for the washer's SVI drive system
• Coordinates drive commands with cycles so the machine advances through wash and spin stages
• Works as the electronic interface between user inputs/controls and the motor drive

• One 1 HP SVI control assembly (single module as shown)

• Disconnect power before servicing and verify machine is fully de-energized
• Handle the module by the edges and avoid static discharge; use ESD protection when available
• Installation requires access to the service panel and secure electrical/mounting connections; refer to the machine service manual