Lfx 25974Sw /00 Parts

This refrigerator sheath heater melts frost from the evaporator so air can circulate freely and the unit can cool properly. Replacing a failed heater helps restore even temperatures and reduce frost buildup in the freezer.

• Warms the evaporator coil during defrost cycles to clear ice
• Helps prevent restricted airflow, warm spots, and long run times
• Common failure symptoms include heavy frost on the evaporator, poor cooling, ice buildup on the back panel, or frequent defrost errors
• May cause sizzling sounds or water under the evaporator area during normal operation after replacement

• Unplug the refrigerator before service; defrost any heavy ice to access parts safely
• Access typically from the rear of the freezer compartment behind the evaporator cover
• Handle heater leads and evaporator fins carefully to avoid damage
• Secure all connectors before reassembly

This rail connector secures a slide rail to its mounting point, keeping the rail aligned and stable so the assembly moves smoothly. Replace a cracked, worn, or missing connector to restore proper tracking and support.

• Joins the slide rail to its bracket or panel to maintain alignment and support
• Helps the rail travel smoothly without binding or coming off track
• Replaces broken, warped, or missing connectors that allow rails to loosen
• Typical signs of failure: rail separates, wobbles, sags, or won't stay engaged

• Disconnect power to the appliance; remove items to access the rail safely
• Remove the drawer/shelf and rail as needed to reach the connector
• Release locking tabs or fasteners, transfer the rail to the new connector, and seat it fully
• Reinstall components and test for smooth travel; wear gloves to protect hands from sharp edges

This connector secures and transmits motion between the drawer drive and the sliding assembly, restoring smooth drawer movement and alignment. It's a direct-fit replacement that helps fix sticking, slipping, or non-moving drawers. What it does:

• Couples the drawer drive mechanism to the sliding gear, allowing the drawer to open and close reliably
• Replaces worn or broken connector teeth or mounts that cause skipping or jammed operation
• Helps correct uneven or noisy drawer movement caused by damaged linkage
• Restores proper engagement so the drawer responds to normal open/close controls

• One connector as shown

• Disconnect power to the appliance before servicing to avoid electrical shock or injury
• Inspect surrounding gears, tracks, and mounting points; replace any damaged parts for best results
• Basic hand tools are typically required; handle plastic gears carefully to avoid further damage

This sensor PCB assembly detects and relays sensor signals to the appliance control system, restoring accurate sensor feedback and communication when the original sensor board fails or malfunctions. Designed as a direct replacement board. What it does:

• Reads sensor inputs and converts them to signals the main control board can interpret.
• Replaces a failed or intermittent sensor board that causes incorrect readings or sensor-related error codes.
• Can resolve symptoms such as unexpected sensor faults, control errors, or appliances not responding to sensor changes.
• Matches the OEM board function; verify model compatibility before ordering.

• Always disconnect power before servicing to avoid shock or shorting the board.
• Use ESD precautions and handle the PCB by its edges to prevent static damage.
• Ensure all connectors are fully seated and the board is mounted in the original orientation.

This display case is the outer housing that holds and protects the appliance control panel and display assembly. It restores a clean finished appearance and shields the electronics from dirt and accidental contact. What it does:

• Houses and secures the control board, display lens and user interface components
• Protects the display and electronics from dust, spills and physical damage
• Restores a solid, aligned control panel if the original housing is cracked, warped or loose
• Improves readability and the appliance's finished appearance

• Disconnect power to the appliance before starting any repair.
• Typically fastens with screws or clips; keep hardware and alignment tabs for reassembly.
• Handle the display lens and electronic connections gently to avoid damage.

This hinge secures and guides a refrigerator door for reliable opening and closing. It restores proper door alignment to help maintain an airtight seal and prevent sagging or rubbing. What it does:

• Supports the refrigerator door and attaches it to the cabinet frame
• Guides smooth door movement and maintains alignment
• Helps prevent door sag, uneven gaps, and items catching when opening/closing
• Reduces rubbing, scraping or abnormal door noise caused by a worn hinge

• Disconnect power and remove food from the door before starting; support the door to prevent dropping
• Use the factory mounting screws and follow OEM torque and alignment steps
• Check door position and seal after installation; adjust hinge mounting if necessary

A momentary push-button switch that restores reliable button control on the appliance console. Replaces a worn or non-responsive push switch so the control board receives a clear input when the button is pressed. What it does:

• Sends a momentary electrical signal to the control board when pressed
• Replaces broken, stuck, or intermittently working push buttons
• Helps resolve symptoms like no response from the console, intermittent button function, or a physically damaged button
• Functions as the user input for single-press commands

• One momentary push switch

• Disconnect power before servicing to avoid shock or injury
• Access usually requires removing the control panel or console; use appropriate screwdrivers
• Note connector orientation and gently unplug wire harness—do not pull on wires

This is the dryer/washer main control board that manages the appliance's functions and user commands. Replacing a faulty main PCB restores control panel responsiveness and normal cycle operation when the board is the root cause. What it does:

• Receives input from the control panel and sends signals to motors, valves, heaters, and sensors
• Controls cycle selection, timing, and mode changes
• Can cause symptoms such as unresponsive controls, failure to start cycles, intermittent operation, or displayed error codes when defective
• Works with the appliance's other electronic and power components to coordinate operation

• Disconnect power before accessing or replacing the control board to avoid shock or damage
• Handle the PCB by its edges and avoid static discharge; use a grounded wrist strap if possible
• Confirm connector alignment and seating; do not force connectors or damage wiring

This center hinge assembly replaces the refrigerator door center hinge to restore proper door alignment and smooth operation. It supports the door weight and helps maintain correct sealing for reliable cooling performance. What it does:

• Supports the center of the door, keeping it aligned and preventing sagging
• Provides the pivot point for smooth opening and closing
• Helps maintain a consistent door seal to prevent cool-air loss
• Can eliminate shifting, squeaking, or uneven door gaps caused by a worn hinge

• 1 center hinge assembly

• Disconnect power and empty or support the door before removing the hinge
• Use appropriate tools and a second person to safely support the door during replacement
• Inspect adjoining hinges and mounting hardware; replace any damaged fasteners for best results

This Magic Room cover is the replacement shelf panel that closes and protects the refrigerator's Magic Room compartment, keeping foods separated and organized for easy access. What it does:

• Replaces a cracked, chipped or missing Magic Room shelf panel
• Provides a flat surface over the Magic Room compartment to support containers and produce
• Helps keep items separated from the drawer below for better organization
• Restores proper fit and appearance inside the refrigerator

• Remove any items and the Magic Room drawer before installing the cover
• Align the panel with the shelf supports and lower into place until it snaps or seats securely
• Handle carefully to avoid chipping or scratching the plastic

This shelf assembly is a tempered glass storage shelf that provides a flat, stable surface for arranging food and containers in the refrigerator. It restores usable storage space and helps keep items organized and contained. What it does:

• Replaces a cracked, chipped or missing refrigerator shelf to prevent items from falling or spilling.
• Provides a level surface for storing food, pitchers and containers.
• Fits into existing shelf tracks or support clips to lock into position.
• Helps maintain airflow and visibility inside the fresh-food compartment.

• Unplug the refrigerator or switch off power at the breaker before servicing.
• Remove food and supports, then lift the broken shelf straight out, supporting glass to avoid dropping.
• Slide the new shelf into the existing tracks or align with support clips until it seats securely.
• Handle tempered glass carefully and dispose of broken glass per local regulations; wear gloves and eye protection.

This replacement cover is an exterior access panel that protects internal components and restores the appliance's finished appearance. It keeps wiring and mechanisms enclosed while maintaining the cabinet's original look. What it does:

• Covers and protects internal components from dust, spills, and accidental contact
• Restores the appliance's cosmetic appearance when the original cover is cracked, chipped, or missing
• Helps maintain proper airflow routing and component spacing behind the panel
• Prevents small objects from entering service areas that could cause damage

• One replacement cover

• Disconnect power and water before starting any repair
• Remove fasteners or release retaining clips holding the old cover; keep hardware if re-using
• Align the new cover carefully and secure with the original screws or clips; do not force into place
• If clips or mount points are damaged, replace them before finishing installation

This cover cap is a small plastic trim piece that protects exposed fasteners and improves the appliance's appearance. It snaps into place to hide mounting posts and help prevent snags or debris buildup. What it does:

• Covers and protects exposed screws, posts, or fasteners for a finished look
• Prevents lint, dust, and debris from collecting around the mounting point
• Reduces the chance of fabric snags or contact with sharp edges
• Restores worn or missing trim for improved cosmetics

• Disconnect power to the appliance before starting any service that exposes electrical components
• Usually installs by snapping over the post or press-fitting into the trim opening — no special tools required
• If needed, remove adjacent trim pieces to gain access, then reinstall trim in reverse order
• Inspect surrounding mounting hardware for damage and replace if necessary

This indoor AC motor powers the evaporator–side fan in compatible split-system indoor units, circulating air across the coil to maintain cooling comfort. Designed as a direct replacement to restore proper airflow and indoor cooling performance. What it does:

• Spins the indoor fan/blower to move conditioned air through the evaporator coil and into the living space
• Restores normal airflow when a failed motor causes weak or no indoor air movement
• Helps prevent uneven cooling and assists in proper refrigerant heat exchange
• Works with the indoor blower assembly and motor mounting hardware

• Disconnect power at the breaker before attempting any repair to avoid shock
• Mounting screws, wiring connectors, or brackets may be required—reuse existing hardware unless replacements are specified

This replacement funnel redirects ice or water from the dispenser/ice maker chute into the bin or dispenser chute to reduce spills and misdirected flow. It restores proper flow path for reliable dispensing. What it does:

• Guides ice and water from the ice maker/dispenser into the collection bin or dispenser chute
• Helps prevent splashing, misdirected ice, and small leaks at the dispenser area
• Replaces cracked or warped funnels that allow drips or jammed ice
• Works as the molded channel piece shown in OEM parts diagrams for the dispenser/ice assembly

• One funnel

• Disconnect power (and water supply if applicable) before starting work
• Remove only the panels and components required to access the dispenser/ice assembly; follow the appliance service manual steps
• Handle the part carefully to avoid damage; verify orientation before final reassembly