Lfx29945st00 Parts

This replacement funnel channels flow cleanly through the dispenser/fill area, guiding it into the correct passage to help prevent spills, drips, and messes when the original piece is cracked, warped, or missing.

• Guides flow into the correct passage within the dispenser or fill area
• Helps reduce drips, leaks, and misdirected flow caused by damage or wear
• Restores clean, accurate dispensing and a tidy appearance
• Common symptoms include leaking/dripping at the dispenser, misdirected stream, visible cracks, or a loose/missing funnel

• Disconnect power; shut off water supply if applicable
• Remove surrounding trim or fasteners carefully and retain hardware for reuse
• Clean the mounting area before installing the new funnel
• Ensure tabs/locks fully seat; secure fit before restoring power and water

This holder assembly is a structural mounting piece that supports and secures an internal component in your appliance. Replacing a cracked or worn bracket helps restore proper alignment and keeps parts stable during everyday use.

• Provides a rigid mounting point for the attached component
• Keeps parts aligned to reduce movement and vibration
• Helps prevent rattling or noise from loose mounts
• Common signs of failure: visible cracks/broken tabs, looseness, or parts that won't stay seated

• Disconnect power and, if applicable, turn off the water supply before service
• Note the orientation of the original part to match fitment
• Reuse existing mounting screws or hardware unless the manufacturer specifies otherwise
• Do not overtighten fasteners; the secured component is fully seated and stable

This replacement screw secures specified panels or components inside your appliance. Refreshing worn or missing hardware helps restore a tight fit, reduce rattling, and keep assemblies properly aligned for reliable performance.

• Provides secure fastening for brackets, panels, or internal assemblies
• Replaces stripped, rusted, or lost hardware
• Helps reduce vibration and rattling noises
• Symptoms include loose panels, shifting components, or a screw that won't tighten

• Disconnect power and allow any hot surfaces to cool before servicing
• Wear cut-resistant gloves and eye protection
• Match length and thread to the original; replace like-for-like
• Start threads by hand to avoid cross-threading; do not overtighten

This power cord assembly supplies AC power from the wall outlet to your appliance. Replacing a frayed, heat-damaged, or loose cord restores safe, reliable operation and can eliminate intermittent power loss.

• Carries line voltage and ground into the unit to power controls and components
• Routes electricity safely into the cabinet to protect internal wiring
• Replace at the first sign of damage to reduce shock or fire risk

• Disconnect power at the outlet/breaker before servicing
• Compare the new cord to the original; transfer any clips or grommets from the old cord if needed
• Route and secure the cord exactly as original; keep clear of sharp edges and moving parts
• Ensure all connections are fully seated and the ground is properly secured before restoring power

This sub PCB assembly is an electronic control board that processes inputs and switches components, coordinating specific appliance functions. Replacing a failed board can restore normal operation and resolve dead controls, error codes, or intermittent, unpredictable behavior. What it does:

• Distributes and regulates control power and switches loads via onboard relays/triacs
• Interprets signals from sensors and the user interface to execute commands
• Coordinates timing and operation of related components per the appliance's program logic
• Failure may present as no power, won't start, unresponsive or flickering display, random beeps, or recurring error codes

• 1 sub PCB assembly

• Disconnect power to the appliance before servicing; verify no voltage is present
• Use ESD protection and handle the board by the edges
• Photograph wiring; transfer connectors one at a time and ensure they are fully seated
• Secure the board with existing fasteners/standoffs; perform any required reset or diagnostic per your model's service info

The SWITCH, MAGNET is an OEM part for LG refrigerators. It is a switch designed to function in conjunction with the magnetic door seal, indicating to the refrigerator when the door is open or closed. This allows the refrigerator to regulate temperatures properly based on door positioning. 

Symptoms of a bad switch, magnet can include:

•  Temperature control issues, with the fridge struggling to maintain proper coolness levels
•  The fridge fails to switch to energy-saving modes when the door is closed 
•  Lights not turning on or off correctly when the door is opened or closed

Replace yours today with this genuine OEM LG part to ensure consistent and reliable temperature control. This OEM LG part is also compatible with Sears/Kenmore.

This hinge bolt secures the hinge to the appliance cabinet or door, keeping alignment true and motion smooth. Replacing a stripped, missing, or corroded bolt helps restore proper door operation and reliable closing.

• Fastens the hinge to support and stabilize the door
• Helps maintain alignment for smooth opening and closing
• Replaces damaged, stripped, or missing hardware

• Disconnect power to the appliance; shut off water supply if applicable
• Support the door to prevent strain on remaining hardware; enlist a second person if needed
• Note the order/orientation of any shims or washers and transfer them during reassembly
• Start threads by hand to avoid cross-threading; tighten securely without overtightening

The Thermistor Assembly, PTC is an OEM part for LG refrigerators. Located within refrigerator compartments, the thermistor monitors interior temperatures sending signals to the control board. It contains a temperature-sensitive resistor to provide precise feedback on cooling needs. This feedback allows the refrigeration system to maintain consistent temperatures across all food storage areas. 

The causes of thermistor issues arise from normal component degradation, impacts, water damage, and manufacturing defects affecting sensor accuracy.

Symptoms of a bad Thermistor Assembly include:

• Fluctuating or inaccurate temperature readings  
• Compartments failing to maintain proper cooling levels
• Frost or condensation builds up inside
• Repeated Auto Defrost error messages

This genuine LG replacement preserves dependable monitoring for balanced refrigeration control. Keeping food fresher longer and suitable for Sears/Kenmore refrigerators with LG components.

This upper hinge assembly supports the refrigerator door at the top, providing a smooth pivot and proper alignment. Replacing a worn hinge restores even gaps and a tight seal to help maintain consistent cooling performance.

• Supports the door's weight and provides the top pivot point
• Maintains alignment for correct gasket compression and a tight seal
• Helps the door open and close smoothly without rubbing or binding
• Common signs of wear: door sagging or misalignment, rubbing/clicking noises, and poor sealing or condensation around the gasket

• Unplug the refrigerator before servicing.
• Remove the top hinge cover; retain screws and any shims for reuse.
• Support the door with a helper while removing and installing the hinge.
• Position the new hinge, align the door, then tighten screws and verify smooth swing and full gasket contact all around.

This compressor damper is a vibration-isolating mount that sits between the sealed-system compressor and the chassis. It cushions the compressor to reduce noise, limit vibration transfer, and help keep refrigerant lines from being stressed.

• Isolates the compressor from the frame to absorb start/stop shock and vibration
• Helps reduce humming, rattling, or buzzing from the back/bottom of the appliance
• Replaces a damper that's cracked, flattened, hardened, or missing
• Can help if the compressor rocks or the unit vibrates excessively

• Disconnect power and pull the unit forward for access; remove rear/service panel if present
• Support the compressor to relieve load on the mounts before removing fasteners
• Match orientation; transfer any sleeves/spacers from the old damper to the new one
• Ensure the compressor sits level and that tubing is not strained before restoring power

This door basket is the inner door panel that holds items and protects internal components, restoring proper loading and access. It replaces a cracked, dented, or broken basket to help secure contents and improve door closure. What it does:

• Provides a rigid storage surface on the appliance door and protects internal mechanisms.
• Stops items from falling out when the door opens; prevents rattling and extra movement.
• Restores proper alignment and secure closure when the original basket is damaged or cracked.
• Helps maintain a clean interior by covering internal cavities and trim.

• Disconnect power to the appliance before beginning any service.
• Remove any items from the door and support the door while detaching the old basket.
• Line up mounting tabs and fasteners; press or secure the basket until it snaps into place.
• Inspect seals and hinges after installation; test door operation before regular use.

This bushing is a replacement shaft support that stabilizes a rotating assembly and helps reduce wear and noise. It restores smooth movement and helps maintain proper alignment for the appliance component. What it does

• Supports and centers a rotating shaft or drum to reduce wobble and rubbing
• Reduces noise and friction from worn pivot or support points
• Helps prevent uneven wear on mating parts and prolongs assembly life
• Commonly replaced when you hear squeaking, grinding, or notice excessive play

• One bushing

• Inspect mating surfaces and replace any damaged clips, seals, or fasteners as needed
• Use basic hand tools; hold the assembly steady and press the bushing squarely into place
• If the bushing is press-fit, use a suitable driver or press to avoid damage
• Disconnect power and follow all safety precautions before beginning repairs

This name plate is the exterior emblem that mounts to the appliance's front panel. It replaces a missing, cracked, or faded badge to restore a clean, factory look and cover the designated trim area.

• Attaches to the outer panel to display brand/series identification
• Restores a finished appearance where the original emblem sits
• Direct replacement for a lost, damaged, or worn badge
• Typical symptoms: missing emblem, loose or broken tabs, peeling, or discoloration

• Disconnect power before servicing the appliance
• Carefully remove the old emblem; release any tabs from behind or peel away remaining adhesive
• Clean and dry the mounting surface; remove all residue for best fit
• Align with the recess/holes and press evenly until fully seated

This cover tube is a molded protective housing that shields internal components and wiring from wear, heat, and debris. It helps maintain safe operation and prevents rubbing or chafing that can lead to damage. What it does:

• Covers and protects internal wiring, hoses or assemblies from contact and abrasion
• Helps direct airflow and keeps debris away from sensitive parts
• Reduces noise caused by rubbing or loose components
• Preserves component alignment and prevents premature wear

• Disconnect power to the appliance before beginning any repair.
• Installation requires partial disassembly of the appliance; keep track of screws and clips.
• Use OEM replacement and follow the service manual for correct orientation and torque of fasteners.
• If you see damaged wiring or other compromised parts, replace or repair those items before reinstalling the cover tube.

Replacement lamp cover that protects and diffuses an appliance's interior light, restoring even illumination and shielding the bulb from spills and contact. Restores proper light output and appearance after a cracked or missing lens. What it does:

• Protects the interior light bulb from food splatter, grease, and accidental contact.
• Diffuses and evens interior illumination to reduce hot spots and glare.
• Replaces cracked, yellowed, or missing lenses that can cause dim, flickering, or exposed-bulb issues.
• Matches the original lamp housing shape and secures with the appliance's existing clips or screws.

• Always disconnect power (unplug appliance or switch off circuit) and allow the bulb to cool before beginning.
• Remove any retaining screws or clips carefully; handle the cover gently to avoid cracking.
• Seat the cover securely in the lamp housing and reinstall original hardware—do not overtighten screws.
• After installation, restore power and verify the light operates and the cover is properly seated.