Lfxs24623 Parts

This sheath heater is the heating element used in compatible electric dryers to generate hot air for drying. Replaces a worn or failed heater element to restore normal drying performance and reduce extended dry times. What it does:

• Heats air inside the dryer cabinet so clothes can dry efficiently.
• Commonly linked to symptoms like clothes not drying, extended drying cycles, or no heat from the dryer.
• Works with the dryer's thermostats and thermal fuses; a faulty heater can mimic other heat-related failures.

• Disconnect power at the breaker before servicing — this part involves live AC voltage.
• Inspect and replace any open thermal fuses or failed thermostats at the same time as recommended by the model service guide.
• Handle the element carefully to avoid bending or damaging the sheath; follow OEM instructions and torque specs during reassembly.

This door holder secures the microwave door assembly to the cabinet, restoring proper alignment and a snug close. Replace a broken or worn plastic retainer to reduce rattling and help the door seat correctly. What it does:

• Secures the door assembly to the oven frame so the door sits flush and aligned
• Helps the door engage the latch correctly for reliable closing
• Reduces door movement and rattling caused by a cracked or missing retainer
• Commonly replaced when the door feels loose, sags, or won't stay properly seated

• One door holder

• Disconnect power before starting work; never service a microwave while it's energized
• Remove door trim and glass panels carefully to avoid damage; keep track of small screws and clips
• Test door alignment and smooth operation after installation; do not force parts into place

This small stopper installs in the refrigerator to limit the travel of a moving component and keep it securely in place. Replacing a broken or missing stopper prevents over-extension and helps maintain smooth, aligned operation.

• Limits the range of motion for a door, bin, or drawer to prevent over-opening or accidental removal
• Helps keep interior components aligned and operating smoothly
• Replace if cracked, missing, or deformed
• Common symptoms: drawer or bin slides out too far, door swings past normal range, or a broken plastic stop is found

• Disconnect power before servicing; remove or support the affected bin/drawer/door
• Note the old stopper's orientation and location before removal
• Transfer and reuse any original screws or clips if applicable
• Snap or fasten the new stopper in place and test for smooth movement

A small retaining pin used to secure moving parts and keep components aligned for smooth operation. Replacing a worn or broken common pin can stop rattling and restore proper fit between linked parts. What it does:

• Holds or aligns two parts together so they move correctly and stay in position
• Helps prevent rattling, looseness, or parts slipping out of place
• Works as a simple mechanical fastener—no electronics involved

• One common pin

• Disconnect power to the appliance before beginning any service
• Keep track of small parts; lay out components in order to aid reassembly
• May require removal of trim or a hinge/retainer to access the pin—use basic hand tools
• If the pin is difficult to seat, do not force; inspect mating parts for damage

This cover assembly replaces the top cover for an ice maker bucket, protecting ice from contamination and helping the dispenser operate cleanly. It restores the proper enclosure for stored ice and supports correct ice dispensing. What it does

• Replaces a cracked, warped or missing ice bucket cover that lets ice become exposed or contaminated
• Helps maintain proper ice containment so the dispenser and auger can move ice without obstruction
• Reduces ice spillage and prevents debris from entering the ice storage area
• Supports normal operation of the ice bucket and dispenser when used with the original bucket assembly

• One cover assembly for the ice bucket

• High-level, typically user-serviceable: remove the ice bucket, unhook the old cover, and snap or screw the new cover into place
• Power/disconnect: turn off dispenser power or unplug refrigerator before starting to avoid moving parts during install
• Handle gently: plastic parts can crack if forced; align tabs and fasteners before pressing into place

The Water Filter Assembly is an OEM part for LG refrigerators equipped with water dispensers and ice makers. This important assembly helps ensure clean, pure water for drinking and ice production.

Causes of a bad water filter can include failure to change filters regularly as recommended, damage to internal filter components from freeze or impact, or issues with the filter housing seal allowing untreated water to bypass filtration.   

Symptoms of a bad water filter assembly include:

• Cloudy, sediment-filled water dispensed   
• Decline in filter's contaminant removal abilities
• Noticeable tastes or odors emerging from water and ice  
• Filters requiring replacement before recommended schedules

Replace yours today with this genuine OEM LG assembly before contaminants can affect equipment operation or your family's health. New filters restore optimal filter lifespan. This replacement part is compatible with Samsung, GE, and some Kenmore refrigerator models.

This fan grill assembly covers and directs airflow for the refrigerator fan, helping maintain proper circulation and protect the fan from debris. It restores the cabinet air channel and keeps internal components shielded for reliable cooling. What it does:

• Replaces a cracked or broken grill that lets dust or food debris reach the fan
• Restores intended airflow path to help the evaporator/condenser fan work efficiently
• Reduces noise from loose or damaged grill pieces rubbing the fan
• Helps protect internal wiring and fan blades from accidental contact

• One fan grill assembly

• Remove power to the appliance before starting any repair to avoid shock or injury
• Access may require removing interior panels or shelves; follow your model's service manual
• Handle the grill carefully to avoid cracking plastic tabs; use proper fasteners when reinstalling
• If airflow or noise issues persist after replacement, inspect the fan motor and mounting for damage

This rail holder secures the microwave door rail so the door stays aligned and operates smoothly. Replaces a worn or broken holder to reduce door wobble and improve closing action. What it does:

• Secures and supports the door rail assembly for proper door alignment
• Keeps the rail from shifting, preventing rubbing, rattling or uneven gaps
• Helps restore smooth opening and closing of the door
• Fits where the rail mounts to the door frame or trim

• One rail holder

• Disconnect power to the appliance before beginning any repair
• Use basic hand tools (screwdriver/trim tool) and handle plastic parts gently to avoid breakage
• Inspect surrounding clips/rails for damage and replace if needed for a lasting repair

This rail holder is the replacement support that secures an appliance rail in place, restoring proper alignment and smooth movement. It helps keep sliding components stable so drawers or rails track correctly and safely. What it does:

• Secures the rail or slide to the appliance frame to prevent sagging or misalignment
• Restores smooth, controlled movement of sliding parts
• Helps eliminate rattling, binding or uneven travel caused by a loose or broken holder
• Works as a direct-fit support when the original holder is damaged or worn

• Disconnect power and remove any movable components before beginning work
• Installation typically requires basic hand tools; keep fasteners from the original part for reuse if undamaged
• Inspect adjoining rails, slides and mounting points; replace any damaged hardware for best results

This main PCB control board is the appliance's central power/control module that manages electrical signals for normal operation. Replacing a failed board restores control functions and helps the appliance run reliably. What it does

• Regulates and distributes power to the appliance's control circuits and sensors.
• Interprets user inputs and coordinates operational commands to subsystems.
• Can cause the appliance to lose power, fail to start, or show control errors when defective.
• Replacing a faulty board often resolves intermittent operation, unresponsive controls, or unexpected shutdowns.

• Disconnect power at the breaker or unplug the appliance before starting work.
• Handle the board by its edges and avoid touching components or connectors to prevent ESD damage.
• Verify connector orientation and secure all wiring harnesses; do not force connectors.

This PTC cover is the protective housing that shields a PTC sensor/assembly from debris and physical damage, helping maintain reliable sensor performance and prolong component life in the appliance. What it does:

• Protects the PTC sensor or PTC assembly from dust, impact, and accidental contact
• Helps prevent shorting or intermittent sensor signals caused by contaminants
• Supports proper positioning and mounting of the PTC component
• Can help address symptoms such as visible sensor damage, exposed wiring, or intermittent operation related to a compromised sensor housing

• Disconnect power to the appliance before starting any repair
• Remove the outer panel(s) as needed to access the PTC location; handle surrounding wiring and components carefully
• Replace only with the correct OEM cover to ensure proper fit and protection

This is a genuine replacement screw used to secure appliance panels and components. It restores proper fastening so panels and assemblies stay aligned and operate safely. What it does:

• Fastens panels, brackets, and small assemblies to maintain structural integrity
• Replaces missing or stripped screws that cause rattling or loose parts
• Helps stop vibration-related noise when used in its original mounting locations
• Matches the OEM fit to ensure proper alignment and clearance

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread or component damage
• Disconnect power to the appliance before working on electrical components
• Replace all matching fasteners for even fit

This cap assembly for the duct secures and seals a dryer/exhaust duct connection to restore proper airflow and help prevent leaks. Designed to replace a worn or damaged duct cap and keep the vent path intact. What it does:

• Caps and secures the duct outlet to maintain a tight connection and reduce air leakage
• Helps direct exhaust airflow through the duct instead of escaping at the connection
• Can reduce lint and moisture escaping at a faulty or damaged duct joint
• Commonly replaced when the original cap is cracked, broken, or no longer holds the duct in place

• One cap assembly

• Disconnect and power off the appliance before servicing; follow the manufacturer's service manual
• Basic hand tools typically required; check panel or vent access before starting
• Inspect surrounding duct and fasteners; replace damaged clamps or tape as needed

The Power Cord Assembly is an OEM replacement part for LG refrigerators. It includes the electrical cord and strain relief that links the refrigerator to an external power source.  

This power cord assembly safely delivers electricity from the wall outlet to the internal compressor and fan modules. It facilitates proper cooling functions through this transmission of alternating current.

Symptoms of a bad power cord can include:

• Abnormal sounds such as humming or buzzing from within 
• Tripped circuit breakers interfering with operations
• Indicators of cord damage like frays or exposed wiring
• Inconsistencies in interior temperature maintenance

Causes may involve normal wear over extended use, physical stress, or accidental damage to the cord insulation.  

Replacing the power cord assembly with this genuine LG OEM part restores a reliable electrical pathway. It ensures a continued power supply to keep foods fresh and frozen.

This bracket assembly secures the motor to the appliance chassis, keeping the motor stable for reliable operation and reducing vibration. Use this part to replace a worn or damaged motor mount and restore proper motor alignment. What it does:

• Holds the motor in the correct position to ensure the drive components remain aligned
• Reduces motor movement and vibration that can cause noise or premature wear
• Helps prevent rubbing or contact between the motor and cabinet that may cause damage
• Commonly replaced when motor mounting points are cracked, bent, or broken

• Disconnect power to the appliance before beginning any repair
• Handle sharp sheet-metal edges carefully and support the motor during removal/installation
• Verify motor alignment and secure all fasteners to the manufacturer's torque or tightness guidance
• If other mounting hardware is missing or damaged, replace it with OEM-specified fasteners

This cap assembly seals and protects the dryer/refrigeration vent duct where it exits the appliance, helping direct airflow and keep outside air, moisture, and debris out of the duct system. It's a direct-replacement external vent cap. What it does:

• Covers and seals the duct outlet to maintain proper airflow and reduce drafts
• Helps prevent moisture, pests, and debris from entering the duct
• Supports consistent venting to help avoid lint buildup and reduced performance
• Replaces a damaged, cracked, or missing duct cap to restore a proper exterior seal

• One cap assembly for the duct outlet

• Disconnect power and, if applicable, gas before beginning any work
• Remove old cap carefully; wear gloves to protect against sharp edges and lint
• Check and clear the vent path of lint and debris while replacing the cap