Lfxs285660/02 Parts

This door stopper cushions and limits the travel of a refrigerator door to prevent slamming and reduce wear on the hinge and cabinet. Replaces a worn or broken stopper to restore smooth, controlled door movement. What it does:

• Acts as a bumper and travel limiter to prevent the door from hitting the cabinet
• Absorbs impact to reduce noise and protect hinge components
• Helps the door close and align properly when opening and closing
• Commonly replaced when cracked, missing, or excessively worn

• Turn off and unplug the appliance or disconnect power before starting any work
• Remove the hinge or door trim as needed to access the stopper following the manufacturer service instructions
• Replace the stopper by removing the old piece and securing the new stopper in the same position; retain original fasteners unless replacement is required

The Temperature Sensor is an OEM part for LG refrigerators. Also known as a thermistor, is responsible for sensing the temperature changes and providing the necessary feedback to the refrigerator's control board. It helps maintain accurate and consistent temperature levels, ensuring optimal food preservation and efficient cooling.

Causes of a faulty temperature sensor can include wear and tear over time, damage due to electrical issues or exposure to extreme temperatures, or sensor calibration issues. These factors can result in temperature inconsistencies, inaccurate readings, or improper cooling performance of the refrigerator.

Symptoms of a bad temperature sensor may include:

• Incorrect temperature readings on the control panel
• Temperature fluctuations inside the refrigerator
• Overcooling or inadequate cooling of food items

This OEM LG part can also be used on Kenmore/Sears appliances. 

Restore a tight seal on your freezer by replacing a worn gasket. A fresh, pliable gasket keeps cold air in, limits frost and moisture around the door, and helps your freezer maintain stable, food-safe temperatures.

• Creates the air-tight seal between the freezer door and cabinet frame
• Helps maintain correct freezer temperature and energy efficiency
• Reduces frost/ice buildup and condensation near the door opening
• Symptoms include tears, warping, gaps, excessive frost, or the door not closing flush

• Disconnect power before servicing
• Warm the gasket in hot tap water or with low heat to improve flexibility
• Clean and dry the door channel; press the gasket fully into the retainer, starting at the corners
• Close the door and check the seal all around; adjust as needed and allow time for the gasket to conform

This indoor fan motor powers the air conditioner's indoor unit blower to move air across the evaporator coil. Replacing a weak or failed motor restores proper airflow for effective cooling and comfort.

• Drives the indoor blower/crossflow fan to circulate conditioned air
• Maintains correct airflow across the evaporator for cooling and dehumidification
• Common symptoms of failure: no or weak airflow, fan won't start or stalls, intermittent operation
• May cause unusual buzzing/grinding noises or the unit shutting down with a fan-related fault

• Disconnect power at the breaker before servicing; allow moving parts to stop
• Remove the indoor unit cover and access panel; note wire harness connections and routing
• Transfer any brackets, insulators, or hardware from the old motor if required
• Ensure the fan wheel spins freely and does not rub before restoring power and testing

This sensor PCB assembly detects and relays sensor signals to the appliance control system, restoring accurate sensor feedback and communication when the original sensor board fails or malfunctions. Designed as a direct replacement board. What it does:

• Reads sensor inputs and converts them to signals the main control board can interpret.
• Replaces a failed or intermittent sensor board that causes incorrect readings or sensor-related error codes.
• Can resolve symptoms such as unexpected sensor faults, control errors, or appliances not responding to sensor changes.
• Matches the OEM board function; verify model compatibility before ordering.

• Always disconnect power before servicing to avoid shock or shorting the board.
• Use ESD precautions and handle the PCB by its edges to prevent static damage.
• Ensure all connectors are fully seated and the board is mounted in the original orientation.

This rail guide assembly restores smooth, stable sliding for a refrigerator/freezer drawer or shelf drawer, helping the drawer track properly and reducing rubbing or sticking during use. What it does:

• Replaces a worn or damaged drawer slide rail to restore proper alignment and smooth movement
• Helps stop drawers from sticking, binding, scraping, or falling out of track
• Supports the drawer weight and guides it in and out evenly
• Reduces noise caused by misaligned or worn rails

• Disconnect power (and water, if applicable) before servicing the appliance
• Remove the drawer or shelving to access the rail; retain fasteners for reuse unless new ones are provided
• Inspect matching rail on the opposite side; replace both sides if both show wear for best performance

The Leveling Leg is an OEM part for LG refrigerators. It is one of the four legs at the bottom corners that elevate and provide stability to the entire appliance.

Causes of failure can be broken mounting points that no longer provide secure elevation, full compression of the built-in cushioning, or damage from impact on an unlevel floor.

Symptoms of a faulty leveling leg include:

• Excessive shaking or vibrating of the refrigerator
• Door alignment issues where doors are difficult to open or close fully
• Visible leaning or misalignment of the refrigerator cabinet

This OEM LG part is also compatible with some Kenmore models.

This ice bucket assembly is the removable storage bin that collects and holds cubed ice from the refrigerator ice maker, restoring clean, contained ice storage and proper pickup by the dispenser or scoop. What it does:

• Collects and stores cubed ice produced by the ice maker so ice is contained and ready for use
• Guides ice toward the dispenser/auger area for consistent pickup
• Common symptoms it addresses: cracked or warped bin, ice spilling or falling out, ice not accumulating in the bin
• Fits into the freezer ice maker area and works with the factory guides and ejector mechanism

• Disconnect power to the refrigerator before servicing to avoid injury or damage
• Remove existing bucket by sliding it out of the guides; handle plastic parts gently to avoid cracking
• Reinstall by seating the bucket into the guides until it clicks or seats securely; ice maker components align before restoring power
• After installation, cycle power or run a test ice-making cycle to ensure proper operation

This tray cover protects the appliance tray from spills, debris and everyday wear while restoring a finished appearance. Replacing a damaged or missing cover helps contain messes and keeps internal tray areas accessible for service. What it does:

• Covers and protects the tray area from food, water and debris
• Restores a clean appearance and helps prevent buildup on underlying components
• Stops small spills from spreading into the tray cavity
• Commonly replaced when cracked, warped, broken or missing

• Disconnect power to the appliance before beginning any service
• Remove nearby parts or trays as needed to access the cover
• Do not force the cover; align tabs and fasteners to avoid damage

This ice bank door gasket is the flexible door seal that keeps the ice bin compartment closed to limit warm air and moisture intrusion. Replacing a worn or torn gasket restores a tighter seal and helps reduce frost buildup and ice clumping. What it does:

• Forms an airtight seal around the ice bank/ice bin door to help prevent warm air and moisture from entering the compartment
• Reduces frost buildup, ice clumping, and excessive condensation inside the ice bin area
• Helps stop water or drips that can occur when the door seal is cracked or deformed
• Restores even door contact for proper closing and retention of ice quality

• Disconnect power to the refrigerator and remove the ice bin and any loose items before beginning.
• Inspect the door mounting channel; clean residue and old adhesive so the new gasket seats fully.
• Press the gasket evenly into the door channel, aligning any tabs or locator features; avoid stretching the gasket excessively.
• Use only non-sharp tools to ease the gasket into place; if the model uses clips or adhesive, replace or reapply per the manufacturer's instructions.

The Tray Assy, Drawer is an OEM part for LG refrigerators. This drawer tray provides a dedicated storage compartment in the bottom of the refrigerator. It holds heavier items securely on smooth metal rails, facilitating organization and easy access.

Causes of a bad drawer tray can include cracks or breaks in the plastic over time, wear and tear on the sliding mechanism from frequent use, or damage to the mounting rails that secure the tray in place.

Symptoms of a bad tray include:

• The tray no longer fitting flush or securely within the refrigerator frame
• Excessive movement or rattling of items inside the drawer during opening/closing
• Difficulty extending or retracting the drawer smoothly

This OEM LG part is also compatible with some Kenmore models.

This replacement door basket restores usable storage space on the refrigerator door, holding bottles, jars and small containers so food stays organized and easy to reach. Made to match the original fit and mounting points. What it does:

• Replaces a cracked, broken or chipped door basket that can no longer hold items securely
• Restores proper storage and keeps bottles and containers from shifting or falling
• Replaces missing or warped bins that prevent the door from sealing or organizing contents
• Compatible with factory mounting clips and shelf support locations

• Remove all food and loose items from the door before installing the new basket
• Most door baskets snap into place on molded supports; align tabs and press until secured
• Inspect mounting clips or supports for damage; replace clips if they are broken