Lfxs28968s Parts

This DC motor powers the washer's drum rotation, restoring normal spin and agitation so loads wash and rinse effectively. Designed to replace a worn or failed drive motor for reliable drum movement and consistent cycle performance. What it does:

• Spins the drum and controls agitation for wash and rinse cycles
• Restores normal spinning when the washer won't agitate or spin
• Helps reduce noisy, uneven, or intermittent drum rotation when the motor is the cause
• Works with the washer's electronic controls to regulate motor speed and direction

• One DC drive motor

• Disconnect power before starting and follow the washer manufacturer's service manual
• Basic disassembly of the cabinet and drum support is typically required; keep fasteners organized
• Verify wiring connectors and mounting orientation match the removed motor before final assembly
• Check control board and wiring for faults

This tray cover replaces a damaged or missing appliance tray cover to restore a clean appearance and proper containment of spills. It fits into the existing tray location and helps keep interior surfaces protected during normal use. What it does:

• Covers the appliance tray to help contain spills, crumbs, and minor debris
• Maintains a finished look and helps prevent direct contact with the underlying tray
• Supports proper placement of removable trays or components that sit above it
• Useful when the original cover is cracked, warped, or otherwise compromised

• One replacement tray cover

• Basic snap-in or screw-in installation; confirm orientation before fastening
• Power off and unplug the appliance before attempting any service
• Use gentle pressure to avoid cracking the new cover; do not force damaged fasteners
• Replace missing or damaged screws or clips with OEM-specified hardware

This overload protector is a direct-replacement electrical safety device that helps protect the compressor motor from overheating and overcurrent. It trips the circuit when the compressor draws excessive current, helping prevent damage and allowing normal operation once cooled. What it does:

• Detects excessive current or high temperature at the compressor and interrupts power to prevent motor damage.
• Helps stop hard-starting or repeated short-run cycles caused by motor overload.
• Commonly linked to symptoms such as a refrigerator or freezer that hums or clicks, runs briefly then stops, or fails to maintain proper cooling.
• Works with the start components to ensure reliable compressor startup and protect against electrical stress.

• Always unplug the appliance or disconnect power at the breaker before servicing.
• Handle compressor terminals and wiring carefully; avoid bending or damaging terminal tabs.
• Replace with the identical part number or OEM-specified protector to ensure correct fit and electrical ratings.
• After installation, restore power and observe the appliance through one full start/stop cycle to confirm normal operation.

This LED assembly restores screen illumination by replacing a failed backlight strip. It helps return even, bright lighting to the LCD panel so pictures and menus are visible again without the dim or dark display caused by burned-out LEDs. What it does:

• Replaces the display backlight to restore screen brightness and uniform lighting
• Can resolve symptoms like dim display, dark bands, flickering backlight, or no visible picture with audio
• Works as the LED lighting component mounted behind the LCD panel to illuminate the image
• Designed to match the original LED layout and connector for a direct replacement

• One LED assembly (backlight strip) as shown

• Disconnect power and remove the display panel and bezel before replacing the assembly
• Handle the LCD and LEDs carefully to avoid damage; avoid touching LED surfaces and circuit traces
• Observe ESD precautions and use appropriate tools;

This hinge cover assembly replaces a worn or damaged lid hinge cover to restore a smooth, finished look and protect the hinge area from debris and pinching. It helps keep the hinge area sealed and reduces snagging on the lid edge. What it does:

• Covers and protects the lid hinge and pivot area from dirt and moisture
• Restores a clean appearance where a cracked or missing hinge cover was visible
• Helps prevent clothing or hands from catching on the exposed hinge
• Can reduce rubbing noise caused by contact with a damaged cover

• Basic removal of the lid or access panel may be required; follow for proper disassembly
• Use appropriate hand tools and keep small fasteners secure during reassembly
• Disconnect power (and water for washers) before starting work to avoid injury

This cover assembly replaces the rear outer panel that protects a flat-panel TV's internal components and restores the set's finished appearance. It helps keep circuitry secure and maintains proper ventilation and mounting alignment. What it does:

• Shields internal boards, power components, and connectors from dust and physical damage
• Restores the TV's exterior appearance and hides internal wiring
• Supports rear mounting points and keeps panel openings aligned for proper airflow
• Can resolve visible cabinet damage or gaps that expose internal parts

• Disconnect power and unplug the TV before attempting any repair
• Remove stand or wall mount and place the TV face-down on a soft, protected surface
• Use the original screws and follow the manufacturer's service instructions to avoid damaging clips or connectors

This door gasket assembly replaces a worn or damaged refrigerator door seal to help restore an airtight seal and maintain proper cooling. A properly seated gasket reduces drafts, moisture intrusion, and energy loss. What it does:

• Seals the refrigerator door to keep cold air in and warm air out.
• Helps prevent frost buildup and moisture accumulation inside the compartment.
• Reduces compressor run time and energy usage caused by a leaking seal.
• Addresses symptoms such as warm spots, visible gaps around the door, or condensation on the door edges.

• Disconnect power to the appliance and remove food from the door area before starting.
• Inspect the door flange for damage and clean the mounting surface to ensure a proper seal.
• Seat the gasket fully into the channel; some models require loosening or removing trim screws to install.
• If the door does not close evenly after installation, check hinge alignment and adjust per the OEM instructions.

A replacement rail guide assembly that restores smooth, stable sliding for refrigerator/freezer drawers and shelves. Helps reduce sticking and misalignment so drawers open and close more reliably. What it does:

• Guides drawer or shelf movement along the rail for smooth sliding
• Helps keep drawers aligned and prevents binding or tipping
• Reduces noise and catching when opening or closing drawers
• Restores proper support for heavy or loaded drawers

• Disconnect power or unplug appliance before accessing drawers or internal components
• Remove affected drawer or shelf to access mounting points
• Inspect mounting clips and screws; reuse only undamaged hardware or replace as needed
• Test drawer operation after installation to ensure proper alignment and secure fit

This LED assembly replaces a TV backlight module to restore even screen illumination and image brightness. It mounts behind the LCD panel and provides the LED sources that light the display. What it does:

• Replaces a damaged or failed TV backlight module
• Restores even screen brightness and reduces dark spots
• Helps resolve flickering, dim display, or no-picture issues related to the backlight
• Works as a direct-fit LED module for compatible LG LCD TVs

• One LED assembly

• Disconnect power and remove the TV from power source before beginning service
• Requires partial disassembly of the TV (front bezel and LCD panel removal); handle the panel and LEDs carefully
• Avoid touching LED surfaces and circuit traces; use ESD precautions and appropriate tools

This rail holder is the replacement mounting bracket that secures a drawer or rail assembly in place, restoring proper alignment and smooth movement. It provides a direct-fit replacement when the original bracket is damaged or worn. What it does:

• Secures the rail or slide assembly to keep drawers/rails aligned and tracking smoothly
• Prevents sagging, excessive play, or rail misalignment that can cause binding
• Restores stable support for components that rely on the rail attachment
• Useful when the original holder is cracked, broken, or missing fasteners

• Disconnect power or unplug the appliance before starting any repair
• Access may require removing trim panels or the drawer/rail assembly—keep track of fasteners
• Use appropriate hand tools; avoid forcing parts to prevent further damage

This lever return spring restores proper tension to the lever assembly so the control or latch returns smoothly. A direct-fit replacement designed to restore normal lever movement and function. What it does:

• Provides return tension for the lever to ensure reliable latch or control movement
• Helps stop the lever from sticking or remaining engaged after use
• Restores smooth, consistent operation when the original spring is worn or broken
• Commonly replaced when lever movement feels loose or fails to return

• One spring lever

• Disconnect power (or unplug) and follow appliance safety procedures before servicing
• Access may require removing panels or the control/door assembly; keep fasteners organized
• Inspect mating lever and pins for wear; replace damaged components to prevent repeat failure

This case assembly houses the appliance's printed circuit board and provides the mounting, connection points, and protective enclosure needed for the control electronics to operate reliably. It helps keep the board secure and wired to the rest of the appliance. What it does:

• Holds and protects the control PCB from physical damage and contamination
• Provides the connector ports and wiring paths for power, sensors, and user controls
• Restores proper mechanical mounting when cracked, warped, or broken
• Common symptoms: control panel loose, intermittent power or communication, visible case damage

• Disconnect power at the breaker or unplug the appliance before starting
• Handle the PCB with care and avoid static discharge; use ESD protection if available
• Match and reconnect all wiring harnesses and secure mounting screws; do not force connectors

This button lever is the small control-panel actuator that transfers finger pressure to the underlying switch, restoring reliable button feel and control response. Replaces worn, cracked, or missing levers to make front-panel buttons usable again. What it does

• Acts as the actuator for a specific control-panel push button, transferring user press to the switch beneath.
• Restores button engagement when the original lever is cracked, broken, or has fallen off.
• Helps eliminate intermittent or non-responsive button presses caused by damaged actuators.
• Fits into the control-bezel and aligns the button with the switch for consistent operation.

• One button lever/actuator as shown.

• Disconnect power (unplug or shut off breaker) before servicing to avoid shock or accidental activation.
• Access typically requires removing the control-bezel or panel; handle clips and small fasteners carefully.
• Align the lever onto the switch plunger and secure the bezel; do not force plastic parts to avoid breakage.

This replacement drip tray catches and channels water beneath the appliance to prevent leaks and pooling. It helps maintain proper drainage and reduces the chance of water damage under your refrigerator or freezer. What it does:

• Collects condensation, defrost water, or minor leaks to keep the cabinet floor dry
• Directs water to the evaporator or drain system so it can safely evaporate
• Helps prevent pooling that can lead to odors or mildew
• Restores a damaged or missing tray to stop water from dripping onto the floor

• For safety, unplug the appliance and shut off water supply (if applicable) before installing
• Slide or snap the tray into the designated location; ensure it seats fully and aligns with the drain path
• Inspect surrounding seals and drain channels for blockages or damage while the tray is accessible