Lghs2667keo Parts

Specs: 1.40`` long

This replacement refrigerator water tube routes water or condensate between components and maintains a sealed path. Replacing cracked, kinked, or brittle tubing helps stop leaks and restore proper water movement through the system.

• Provides a sealed path to carry water within the refrigerator assembly
• Maintains proper routing to help prevent kinks and restrictions
• Typical failure signs: water leaking inside or underneath, pooling water, visible cracks/brittleness, restricted flow
• Replacing damaged tubing helps prevent water damage to surrounding parts

• Disconnect power and shut off the water supply before servicing
• Note the original routing and connection points; match the length and path during installation
• Fully seat tube ends into existing fittings; transfer any clips/ferrules from the original as required and avoid sharp bends
• Restore water and power, then run and inspect all connections for leaks

This spiral pin secures components in place within the appliance assembly, providing a tight, durable fit that resists loosening under normal operation. Replacing a worn or missing pin helps restore proper alignment and dependable drive of the linked parts.

• Holds mating parts together with a press-fit connection
• Can help resolve issues like loose or slipping drive components, rattling, or intermittent operation in the affected mechanism
• Maintains correct alignment to reduce wear on adjoining parts

• Disconnect power and shut off water before servicing
• Support the assembly to relieve tension before removing the old pin
• Use the correct size punch/driver to press the pin out and in straight
• Do not force; inspect mating parts for wear and replace if damaged

This refrigerator water tank (reservoir) stores and chills drinking water inside the fresh food compartment, helping deliver a steady, reliable stream to the dispenser. Replace a cracked or leaking tank to stop interior leaks and restore dispenser performance.

• Stores a small volume of drinking water so it's cooled before dispensing
• Helps maintain consistent dispenser flow by buffering line pressure
• A cracked tank can leak water inside the fresh food section, often under the crisper drawers
• A restricted or frozen tank can cause little or no water, or sputtering, from the dispenser

• Unplug the refrigerator and shut off the household water supply; depressurize by dispensing water
• Access the tank, typically behind the lower crisper drawers in the fresh food section; place towels to catch residual water
• Reconnect existing water lines using push-to-connect fittings; cut tubing square and fully seat it
• Restore water and power, check for leaks at all connections, and flush the water system thoroughly

This spacer is a small positioning piece used in refrigerator assemblies to maintain proper clearance and alignment between parts. Replacing a worn or missing spacer helps restore smooth operation and prevents rubbing or binding. What it does:

• Maintains the designed gap between mating parts to prevent friction and wear
• Helps keep assemblies aligned for smooth, consistent movement
• Reduces looseness, rattling, or poor fit caused by a missing or deformed spacer
• Typical signs include visible damage or a missing spacer and misalignment or scraping noises in the area it installs

• 1 spacer

• Disconnect power; if working near water components, shut off the water supply
• Use your model's parts diagram to determine exact location and orientation
• Retain and reuse original fasteners or clips unless damaged
• Do not overtighten hardware; ensure smooth operation after installation

This E-ring is a small retaining clip used in Frigidaire refrigerators to hold components on a grooved shaft or pin. It keeps assemblies secure and operating smoothly by preventing parts from sliding off during normal use. What it does:

• Retains parts on a grooved shaft or pin to prevent axial movement
• Helps keep mechanisms aligned and reduces wobble or separation
• Common symptoms when missing or damaged: loose or fallen-off parts, scraping/rattling noises, or poor operation of the affected assembly

• 1 E-ring

• Unplug the refrigerator before servicing; wear eye protection (spring clips can snap)
• Use needle-nose pliers or an E-clip tool to compress and seat the ring in the groove
• Verify the ring is fully seated and flush in the groove before reassembly
• Keep any spacers/washers in the original order during removal and reinstallation

This light switch controls the interior lamp, turning it on when the refrigerator door opens and off when it closes. Replace a worn or stuck switch to restore proper lighting and prevent the light from staying on. What it does:

• Door-activated plunger switch that opens/closes power to the interior light
• Restores interior lighting when the door is opened
• Resolves lights that stay on with the door closed, which can warm the compartment
• Addresses intermittent or flickering light from worn contacts

• 1 light switch

• Disconnect power before servicing
• Gently pry the old switch from the liner or remove the control housing as required for access
• Transfer the wire connectors to the new switch, matching positions
• Press the new switch fully into place, restore power, and test light operation

Lower hinge secures the bottom corner of a refrigerator door and provides a durable pivot for smooth opening and closing. Replacing a worn hinge restores proper door alignment and helps maintain a tight seal. What it does:

• Supports the weight of the lower door corner and provides a pivot point for opening/closing.
• Keeps the door aligned so the gasket can seal properly.
• Worn or damaged hinges can cause door sag, uneven gaps, rubbing, or difficulty closing.
• Restoring a solid hinge reduces stress on the door and latch for more reliable operation.

• Disconnect power to the appliance and remove food/items from the door before starting.
• Always support the door while removing/installing the hinge to prevent dropping or damage.
• Use the correct tools and hardware; tighten fasteners snugly but avoid over-torquing.
• After installation, check door alignment and seal; adjust as needed for proper operation.

Right side.

This ice cream shelf is the replacement shelf used in the freezer compartment to restore a stable surface for storing ice cream and similar containers. It helps keep frozen foods organized and prevents items from falling or tipping. What it does:

• Replaces a cracked, warped or missing ice cream shelf to restore usable storage space.
• Provides a flat, stable surface for tubs, cartons and other frozen items.
• Prevents containers from sliding or tipping between freezer compartments.
• Restores original shelf alignment so adjacent shelves and drawers fit properly.

• Remove all contents from the shelf area before installing to avoid spills or injury.
• Slide the shelf into the existing support grooves or brackets until fully seated; no special tools typically required.
• Inspect support rails or clips for damage and replace if worn to ensure a secure fit.
• If the shelf is glass, handle with care and wear gloves to prevent cuts.

This control rod spring fits the refrigerator's ice maker shutoff arm. It restores proper tension so the ice maker cycles on/off correctly and stops making ice when the bucket is full.

• Maintains tension on the ice maker control/shutoff arm for reliable on/off operation
• Helps the arm return to position so the ice maker senses a full bin and pauses production
• A weakened or missing spring may cause an overfilling ice bucket, a loose arm, or inconsistent ice production
• Replaces damaged or stretched springs that prevent the control rod from moving smoothly

• Unplug the refrigerator and shut off water to the ice maker
• Empty the ice bin and access the shutoff arm pivot
• Note the spring's orientation; install with needle-nose pliers without bending the control rod
• Restore power/water and verify smooth arm movement and proper shutoff

This factory fastener secures appliance panels and components. Replace a missing, stripped, or corroded screw to restore a tight, rattle-free fit and keep brackets and covers properly aligned.

• Fastens panels, brackets, and internal parts as specified by the manufacturer
• Helps maintain alignment and reduces vibration/rattling
• Replace if the head is stripped, threads are damaged, or corrosion is present
• Symptoms include loose/missing hardware, gaps, or rattling during operation

• Disconnect power; shut off gas/water if applicable before servicing
• Use the correct driver/bit size to avoid stripping the head
• Start threads by hand to prevent cross-threading; do not overtighten
• Match screw length/thread to the location; replace in sets when required

This replacement screw fastens appliance components such as panels, brackets, and covers. Installing a new fastener restores a snug, rattle-free fit when the original screw is missing, stripped, or corroded.

• Secures covers, brackets, or trim to the cabinet or liner
• Replaces missing, stripped, or rusted hardware
• Helps reduce vibration and rattling from loose parts
• Supports proper alignment and stability of assemblies

• Disconnect power before servicing the appliance
• Use the correct driver/bit and start threads by hand to avoid cross-threading
• Do not overtighten, especially into plastic or thin sheet metal
• Retain and reinstall any original washers or spacers, if present

Specs: .875`` long

Replacement ice bin rail that supports and guides the freezer ice bin for smooth sliding and secure positioning. Restores proper bin alignment so the ice bin removes easily and reduces binding, rattling, and accidental drops.

• Supports and guides the ice bin so it slides in and out without sticking
• Keeps the bin properly aligned to prevent tipping or falling when removing
• Reduces noise caused by a loose or worn support rail
• Commonly replaced when the bin binds, catches, or sits unevenly

• Disconnect power to the appliance before beginning any work
• Remove the ice bin and any loose ice before removing the old rail
• Install by seating the rail into the mounting locations and securing with the original fasteners; basic hand tools may be required