Lgus2642leo Parts

This pizza shelf is a direct-replacement oven shelf designed to support pizzas and other flat bakeware for stable, even cooking. Restores a missing or damaged shelf so trays and pans sit level during use. What it does:

• Provides a flat, stable surface for baking pizzas, sheet pans, and similar items
• Replaces a warped, bent or missing pizza shelf that prevents level cooking
• Helps keep cookware centered and supported to reduce sliding or tipping
• Durable finish resists everyday oven use and helps maintain even heat exposure

• Slide shelf onto existing oven rack supports until it sits securely; no tools typically required
• Allow oven to cool before removing or installing the shelf to avoid burns
• Clean with non-abrasive cleaners; avoid harsh scrubbing that can damage the finish
• Follow your oven manufacturer's instructions for safe use and placement

This evaporator cover mounting bracket secures the evaporator cover inside the freezer compartment to keep cooling airflow and components in place. Durable metal construction replaces a broken or bent bracket to restore proper cover alignment. What it does:

• Holds the evaporator cover in position for correct airflow and protection of the evaporator coil
• Helps stop rattling or loose cover movement that can cause noise
• Restores a secure mounting point after impact or corrosion damage
• Works with the evaporator cover assembly to maintain consistent cooling performance

• High-level replacement: remove the evaporator cover to access mounting points; fasten bracket with existing screws
• Use basic hand tools; keep screws and clips organized for reassembly
• Disconnect power to the appliance before starting any repair to avoid electrical hazard

This solenoid actuator is the electromechanical device that moves a latch or linkage when energized, restoring the appliance's intended mechanical action. It provides a direct replacement to re-enable reliable actuation. What it does:

• Converts electrical signal into a mechanical push or pull to operate a latch, door, dispenser or linkage
• Commonly used where a timed or motor-driven movement is needed during a cycle
• Symptoms this part can cause: appliance fails to actuate a door, latch, dispenser or similar mechanism when called for
• Replacing a worn or failed actuator restores proper mechanical response to control signals

• One solenoid actuator

• Disconnect power to the appliance before beginning work to avoid shock or unintended actuation
• Remove any panels or trim as needed to access the actuator; note wire and mounting locations for reassembly
• Reconnect wiring and test the function on a short cycle after installation

A single replacement screw used to fasten appliance panels and components securely. This genuine-style fastener restores proper fit and helps eliminate rattles or loose parts after service or repairs. What it does:

• Secures panels, brackets, or trim to the appliance frame
• Restores tight, stable mounting to stop rattling or vibration
• Replaces missing or stripped hardware so parts align correctly
• Works where the original appliance screw was used

• Use matching driver and apply moderate torque to avoid stripping the head or threads
• Disconnect power or unplug the appliance when accessing internal areas
• If screw threads are damaged, replace with an identical part rather than forcing

This replacement fan shroud screw secures the evaporator/condenser fan shroud to the appliance, helping keep the fan assembly stable for proper airflow and quiet operation. Use it to replace stripped or missing mounting hardware. What it does:

• Secures the fan shroud or mounting bracket to the appliance cabinet or fan assembly
• Helps prevent fan wobble, rubbing, and airflow disruption caused by a loose shroud
• Restores proper clearance between fan blades and shroud to reduce noise and wear

• High-level replacement—remove power to the appliance before starting work
• Use appropriate-size driver to avoid stripping the screw head
• Inspect surrounding hardware and shroud for damage; replace any damaged parts before reassembly

This spring solenoid is the actuator spring assembly that helps move and return a solenoid-driven mechanism, restoring reliable part movement and engagement in affected appliance systems. What it does:

• Provides return tension and controlled movement for a solenoid actuator
• Helps the solenoid plunger snap back after activation so linked components reset
• Commonly replaced when the actuator fails to move, sticks, or does not fully return
• Corrects symptoms such as intermittent engagement, sticking, or loss of actuator motion

• Disconnect power to the appliance before attempting service to avoid shock or injury
• Handle small components carefully; keep track of retaining clips, pins, or fasteners
• Replace with the exact part number to ensure fit and function
• Refer to OEM instructions for step-by-step removal and reassembly

This wiring harness is the appliance's pre-wired connector assembly that routes power and signals between the control and components, restoring proper electrical connections for reliable operation. What it does

• Connects control board, motors, sensors and switches so components receive power and communicate.
• Replaces damaged or frayed wiring that can cause intermittent operation or component failure.
• Stops symptoms like no power to a component, intermittent cycles, blown fuses or visible arcing at connectors.
• Ensures secure plug-to-plug connections and correct wire routing when installed correctly.

• Disconnect power to the appliance before attempting any repair to avoid shock.
• Compare the harness and connector shapes to the original before installing; route wires away from heat and moving parts.
• Secure connectors fully until they click; do not force mismatched plugs.
• If terminals are corroded or connectors are damaged at either end, replace harness or repair terminals per OEM instructions.

This ice ejector is the plastic arm that pushes cubes out of the ice maker mold and into the ice bin, restoring proper ice ejection and dispenser function. It's a direct-replacement component for affected ice maker assemblies. What it does:

• Physically strips and pushes formed ice cubes from the mold into the bin or dispenser
• Helps restore normal ice dispensing when cubes remain stuck in the mold
• Works with the ice maker's motor/gear train to time ejection during the harvest cycle
• Commonly replaced when the ejector is broken, cracked, or worn and no longer contacts cubes

• One ice ejector (ejector arm)

• Disconnect power to the refrigerator before starting any repairs
• Remove the ice maker/cover or access panel as required to reach the ejector
• Inspect related components (drive gear, motor, and mounting pins) for wear while replacing the ejector
• After installation, run a test harvest/dispense cycle to correct operation

This control rod is a direct-replacement linkage rod that connects a user control to the appliance's internal mechanism, restoring reliable mechanical movement and control operation. What it does:

• Transfers motion from an external control lever or knob to the internal mechanism
• Replaces a bent, worn, or broken linkage that causes sticky or non-responsive controls
• Helps restore proper engagement and consistent mechanical action
• Works as a simple mechanical replacement—no electronic programming required

• One control rod

• Disconnect power (and gas if applicable) before beginning any repair
• Basic hand tools may be required; follow the appliance service manual for disassembly steps
• Handle small parts carefully to avoid damage and ensure proper alignment during reassembly