Lmx21984st/00 Parts

This fan motor assembly circulates air across the evaporator coils to keep temperatures even inside the refrigerator. Replacing a worn or noisy motor restores proper airflow for consistent cooling performance.

• Drives the evaporator fan to move chilled air through the cabinet and vents
• Helps maintain stable temperatures and reduces frost from stagnant air
• Common symptoms: weak or no airflow, loud or intermittent fan noise, temperature fluctuations, refrigerator section warmer than expected
• Failures may result from worn bearings, moisture exposure, or an open motor winding

• Disconnect power before servicing; wear cut-resistant gloves and eye protection
• Access the fan behind the interior rear panel; remove shelves/drawers as needed and avoid bending evaporator fins
• Note wire connector orientation and mounting order; transfer any reusable hardware from the original assembly as needed
• After reassembly, verify the fan spins freely and confirm operation before reloading the compartment

This dispenser lever holder is the mounting bracket behind the refrigerator's dispenser paddle. It supports and aligns the lever and switch so water or ice dispenses reliably when the paddle is pressed.

• Holds and guides the dispenser lever and actuator switch inside the dispenser housing
• Provides a secure pivot point for smooth paddle movement
• Helps ensure consistent activation of water and ice dispensing
• Damage can cause a loose or stuck paddle, intermittent dispensing, or no dispense

• Disconnect power and shut off the water supply before servicing
• Remove the dispenser panel/escutcheon to access the lever assembly; note part orientation
• Transfer the lever, switch, and return spring to the new holder and secure with the original fasteners
• Restore power/water and test dispensing before reinstalling trim

This door gasket is the flexible magnetic seal that runs around the edge of the refrigerator door to keep cold air in and warm air out, helping maintain proper temperature and energy efficiency.

• Creates an airtight seal between the refrigerator door and cabinet
• Helps prevent temperature swings, frost buildup, and excess run time
• Common failure signs: torn, warped, or hardened seal; doors not sealing; condensation around the door
• Magnetic strip embedded to pull the door closed against the frame

• Unplug the appliance before starting any repair
• Soften the old or new gasket with warm air (hair dryer on low) to ease removal/fit
• Transfer or seat the gasket fully in the door channel; work evenly around corners
• Check door alignment and perform a dollar-bill test to confirm an even seal

This replacement dispenser funnel sits in the door dispenser area and guides ice cleanly into your glass. Replacing a cracked or missing funnel helps reduce spills and jams for tidier, more reliable dispensing.

• Directs ice from the chute into your container to minimize scatter and mess
• Helps prevent cubes from bouncing out or clogging at the dispenser opening
• Restores proper alignment and flow in the dispenser area
• Common symptoms: ice spilling onto the floor, frequent clogs, loose or broken funnel

• Disconnect power to the refrigerator before servicing the dispenser
• Remove dispenser trim/control panel as directed by your model's service information; support any wiring
• Release screws or tabs securing the old funnel; note orientation and transfer any existing hardware or springs
• Seat and secure the new funnel, reassemble trim, restore power, and test ice dispensing

This holder is a small mounting bracket that secures a mating component in place inside the appliance. Replacing a cracked or missing holder restores a firm, rattle-free fit and proper alignment.

• Provides a stable mount for the designated part
• Prevents shifting and vibration that can cause noise or premature wear
• Common signs of failure: broken tabs, stress cracks, or the attached part sagging or falling out
• When damaged, the connected component may be loose, noisy, or misaligned

• Disconnect power; if working near water tubing, also shut off the water supply
• Note the original orientation and mounting points; take a photo before removal
• Reuse existing fasteners and avoid overtightening to prevent cracking the plastic
• Ensure the attached component is secure and clears any moving parts before restoring power

This cabinet roller supports the refrigerator and lets the unit roll in and out of place for cleaning or service. Replace a worn or broken roller to restore smooth movement and help keep the appliance properly positioned.

• Supports the base of the refrigerator and enables rolling movement
• Helps with safe positioning and service access without dragging
• Common failure signs: appliance is hard to move, scraping or rolling noises, a flat-spotted/cracked wheel, or a wheel that won't turn
• Replace when the roller is damaged, seized, or missing

• Disconnect power and shut off water supply; protect flooring before moving the appliance
• With help, pull the refrigerator forward and safely support it to access the roller
• Remove mounting fasteners, install the new roller, and reuse original hardware
• Confirm level and smooth movement before returning the unit to its location

This replacement temperature sensor measures the compartment temperature and reports it to the control board, helping your refrigerator maintain consistent cooling. Replace a failing sensor to restore accurate temperature readings and dependable performance.

• Monitors refrigerator/freezer temperature and relays data to the control
• Helps the system regulate compressor and fan operation for steady cooling
• A failing sensor can cause temperatures that are too warm or too cold
• May lead to extended run times, short cycling, or erratic cooling

• Disconnect power before servicing; wear cut-resistant gloves.
• Location varies by model; commonly clipped to the evaporator or mounted in an air duct/liner.
• Match the connector, route wiring along the factory path, and secure the probe in its original position.
• Restore power and allow up to 24 hours for temperatures to stabilize.

This light lens covers and protects the interior lamp, diffusing brightness for a clean, finished look. Replacing a damaged lens helps keep the bulb or LED safe from bumps and moisture inside the compartment.

• Shields the bulb/LED from impact and moisture
• Diffuses light for more even illumination
• Restores appearance when the original lens is cracked, yellowed, or missing
• Helps ensure a secure fit

• Disconnect power before servicing and let any hot bulb cool
• Remove shelves or bins as needed for access
• Release the locking tabs or slide the old lens to disengage; avoid prying that could crack plastic
• Seat the new lens fully until the tabs engage; do not force

This holder assembly is a structural mounting piece that supports and secures an internal component in your appliance. Replacing a cracked or worn bracket helps restore proper alignment and keeps parts stable during everyday use.

• Provides a rigid mounting point for the attached component
• Keeps parts aligned to reduce movement and vibration
• Helps prevent rattling or noise from loose mounts
• Common signs of failure: visible cracks/broken tabs, looseness, or parts that won't stay seated

• Disconnect power and, if applicable, turn off the water supply before service
• Note the orientation of the original part to match fitment
• Reuse existing mounting screws or hardware unless the manufacturer specifies otherwise
• Do not overtighten fasteners; the secured component is fully seated and stable

This replacement screw secures specified panels or components inside your appliance. Refreshing worn or missing hardware helps restore a tight fit, reduce rattling, and keep assemblies properly aligned for reliable performance.

• Provides secure fastening for brackets, panels, or internal assemblies
• Replaces stripped, rusted, or lost hardware
• Helps reduce vibration and rattling noises
• Symptoms include loose panels, shifting components, or a screw that won't tighten

• Disconnect power and allow any hot surfaces to cool before servicing
• Wear cut-resistant gloves and eye protection
• Match length and thread to the original; replace like-for-like
• Start threads by hand to avoid cross-threading; do not overtighten

This ice gear transfers motor rotation to the refrigerator's ice mechanism so cubes can be dispensed or ejected. Replacing a worn or stripped gear restores smooth, reliable ice operation and helps eliminate grinding or clicking noises.

• Transfers drive from the motor to the ice mechanism (auger/ejector, depending on model)
• Helps move ice through the system for dispensing or harvest
• Common symptoms: no or slow ice dispensing, auger not turning, loud clicking/grinding from the ice bin
• Cracked or stripped teeth indicate the gear should be replaced

• Disconnect power to the refrigerator before servicing
• Remove the ice bin and access the ice assembly per your model; note gear orientation for reassembly
• Align teeth carefully; do not force the gear onto the shaft
• Inspect related parts (drive coupler, auger, motor shaft) and replace any worn components to prevent repeat failure

STOPPER ASSEMBLY,DOOR

This temperature sensor is the thermistor that monitors compartment temperature and reports it to the control. Replacing a failed sensor helps restore accurate cooling and steady, reliable temperatures in your refrigerator.

• Detects refrigerator or freezer air temperature and sends a resistance signal to the control board
• Helps the control regulate compressor, evaporator fan, and air damper operation
• Also called a thermistor; critical for maintaining stable, set-point temperatures
• Failure symptoms can include sections that are too warm or too cold, erratic temperature swings, or frequent cycling

• Unplug the refrigerator before servicing
• Access location varies by model (often behind an interior cover or air duct); note routing and placement before removal
• Reinstall in the original position and route wiring in the factory path; ensure the connector is fully seated
• Restore power and allow up to 24 hours for temperatures to stabilize

This PTC thermistor assembly feeds temperature feedback to the control so the appliance can monitor conditions and run sensor-based cycles correctly. Replacing a failed sensor restores reliable automatic operation and prevents errors that lead to inconsistent results.

• Detects temperature changes and sends a resistance signal to the main control for sensor/auto functions
• Helps regulate time and power during sensor-driven cycles for consistent performance
• Failure symptoms can include "sensor" errors, cycles ending too soon or running too long, or inconsistent results
• In some models, a bad sensor may prevent sensor modes from starting

• Disconnect power before servicing; microwaves can retain dangerous high voltage—discharge the capacitor before touching internal components
• Access and mounting location vary by model; commonly found behind the grille or near the control in the air duct path
• Route the harness exactly as original; keep wiring away from sharp edges and hot areas
• Avoid touching the sensing tip; ensure all connectors are fully seated

This name plate is the exterior emblem that mounts to the appliance's front panel. It replaces a missing, cracked, or faded badge to restore a clean, factory look and cover the designated trim area.

• Attaches to the outer panel to display brand/series identification
• Restores a finished appearance where the original emblem sits
• Direct replacement for a lost, damaged, or worn badge
• Typical symptoms: missing emblem, loose or broken tabs, peeling, or discoloration

• Disconnect power before servicing the appliance
• Carefully remove the old emblem; release any tabs from behind or peel away remaining adhesive
• Clean and dry the mounting surface; remove all residue for best fit
• Align with the recess/holes and press evenly until fully seated

This lower cover assembly protects the appliance's lower cabinet area and helps keep internal components free from debris while supporting proper airflow. It restores the unit's finished appearance and helps prevent damage to wiring and controls. What it does:

• Shields lower cabinet components from dust, lint and accidental contact
• Helps maintain correct airflow routing under the appliance
• Prevents foreign objects from reaching motors, pumps or wiring
• Re-establishes the finished exterior where the lower panel is missing or damaged

• One lower cover assembly

• Disconnect power (and water, if applicable) before starting work
• Remove any exterior panels or trim as needed; basic hand tools required
• Handle edges carefully; wear gloves to avoid cuts
• Secure all fasteners; replace any damaged clips or screws