Lmx28988st Parts

Keep refrigerator door storage secure and organized with this replacement door basket assembly. It restores a stable shelf on the door so bottles, jars and small items stay upright and accessible. What it does:

• Replaces a cracked, broken or missing door bin to restore door storage capacity
• Secures bottles, condiments and small containers so they don't shift or fall when the door opens
• Aligns with the door rail and mounting points for a stable fit
• Helps maintain organized interior storage without affecting cooling components

• Disconnect power to the appliance before starting any repair
• Remove stored items from the door and lift or unclip the old bin from its mounting rails
• Align the new basket with the door rails and press or secure until it snaps or seats fully; some models may use fasteners—keep original clips/screws if present

This duct assembly routes internal airflow in the appliance, replacing damaged or worn vent tubing to restore proper air movement. It helps reduce air leaks and airflow-related performance issues when the original duct is compromised. What it does:

• Channels blower air from the fan housing to the exhaust path to maintain proper ventilation.
• Replaces collapsed, torn or disconnected ducting that can cause poor airflow.
• Addresses symptoms such as reduced drying/cooling performance, longer cycles, or warm cabinet air.
• Helps eliminate drafty or noisy airflow caused by gaps or damaged duct sections.

• Disconnect power (and turn off gas supply for gas appliances) before beginning service.
• Access may require removing rear or lower access panels; keep hardware organized for reassembly.
• Inspect and replace any damaged clamps, seals or gaskets during installation for a proper seal.

STOPPER ASSEMBLY,DOOR

This name plate is the exterior emblem that mounts to the appliance's front panel. It replaces a missing, cracked, or faded badge to restore a clean, factory look and cover the designated trim area.

• Attaches to the outer panel to display brand/series identification
• Restores a finished appearance where the original emblem sits
• Direct replacement for a lost, damaged, or worn badge
• Typical symptoms: missing emblem, loose or broken tabs, peeling, or discoloration

• Disconnect power before servicing the appliance
• Carefully remove the old emblem; release any tabs from behind or peel away remaining adhesive
• Clean and dry the mounting surface; remove all residue for best fit
• Align with the recess/holes and press evenly until fully seated

This cover tube is a molded protective housing that shields internal components and wiring from wear, heat, and debris. It helps maintain safe operation and prevents rubbing or chafing that can lead to damage. What it does:

• Covers and protects internal wiring, hoses or assemblies from contact and abrasion
• Helps direct airflow and keeps debris away from sensitive parts
• Reduces noise caused by rubbing or loose components
• Preserves component alignment and prevents premature wear

• Disconnect power to the appliance before beginning any repair.
• Installation requires partial disassembly of the appliance; keep track of screws and clips.
• Use OEM replacement and follow the service manual for correct orientation and torque of fasteners.
• If you see damaged wiring or other compromised parts, replace or repair those items before reinstalling the cover tube.

This lower cover assembly protects the appliance's lower cabinet area and helps keep internal components free from debris while supporting proper airflow. It restores the unit's finished appearance and helps prevent damage to wiring and controls. What it does:

• Shields lower cabinet components from dust, lint and accidental contact
• Helps maintain correct airflow routing under the appliance
• Prevents foreign objects from reaching motors, pumps or wiring
• Re-establishes the finished exterior where the lower panel is missing or damaged

• One lower cover assembly

• Disconnect power (and water, if applicable) before starting work
• Remove any exterior panels or trim as needed; basic hand tools required
• Handle edges carefully; wear gloves to avoid cuts
• Secure all fasteners; replace any damaged clips or screws

This fan grill assembly is the molded cover that protects the refrigerator/freezer fan and helps direct airflow for efficient cooling. It restores proper air movement and keeps debris away from the fan blade and motor. What it does:

• Covers and protects the evaporator/condenser fan from loose items and debris
• Directs airflow to support consistent cooling and efficient operation
• Reduces fan noise caused by damaged or loose grills
• Prevents accidental contact with the spinning fan blade

• Disconnect power to the appliance before servicing to avoid electrical shock or injury
• Typically secures with screws or retaining clips; keep all fasteners and align tabs before tightening
• Handle the plastic grille carefully to avoid cracking; confirm correct orientation before final install
• If fan or motor damage is present, inspect and replace those parts as needed

This damper motor support replaces a broken or warped mount for the refrigerator's air damper assembly. It holds the damper motor and door securely so the system can meter freezer air into the fresh food compartment.

• Secures and aligns the air damper motor/door within the duct
• Helps ensure proper opening/closing of the damper to regulate airflow and temperature
• Damage can contribute to a warm or too-cold refrigerator and inconsistent temperatures
• May cause clicking or buzzing from the damper area or a visibly loose assembly

• Disconnect power to the refrigerator before servicing
• Access the damper behind the fresh food compartment duct/cover; remove shelves as needed
• Note wiring and orientation; transfer the existing damper motor and door to the new support and reuse fasteners
• Ensure the door moves freely and seals before reassembly; restore power and verify airflow

This hinge secures and guides a refrigerator door for reliable opening and closing. It restores proper door alignment to help maintain an airtight seal and prevent sagging or rubbing. What it does:

• Supports the refrigerator door and attaches it to the cabinet frame
• Guides smooth door movement and maintains alignment
• Helps prevent door sag, uneven gaps, and items catching when opening/closing
• Reduces rubbing, scraping or abnormal door noise caused by a worn hinge

• Disconnect power and remove food from the door before starting; support the door to prevent dropping
• Use the factory mounting screws and follow OEM torque and alignment steps
• Check door position and seal after installation; adjust hinge mounting if necessary

Replacement drain tube assembly that directs wastewater from the appliance tub to the drain pump, restoring proper drainage and helping reduce leaks. Use when the original tube is cracked, kinked, clogged, or visibly leaking. What it does

• Channels wastewater from the tub to the drain/pump for normal draining.
• Maintains a sealed path to help prevent water leaks under or around the appliance.
• Replace when you see pooling water, slow or no drain, or visible damage to the tube.
• Works as the fluid conduit; does not include clamps or pump.

• Disconnect power and water supply before beginning any service.
• Route the tube along the original path and secure with existing clamps or the correct replacement fasteners.
• Avoid kinks, sharp bends, and contact with sharp edges to prevent leaks or premature wear.
• After installation, restore power/water and run a short drain cycle; check all connections for leaks.

This sub power control board assembly controls and routes electrical power and control signals for the appliance, restoring electronic control when the original sub-PCB fails. Use this board to address power and control-related faults. What it does:

• Regulates and routes power to motors, valves, sensors and other control circuitry.
• Processes low-voltage control signals from the main board, user interface and sensors.
• Common symptoms linked to a failing board: no power or no response, intermittent operation, error codes or unresponsive controls.
• Replacing the faulty sub control board can restore normal electronic operation and command response.

• Disconnect the appliance from power before beginning any service.
• Handle the PCB by the edges and use proper ESD precautions to avoid static damage.
• Verify all connectors are fully seated and wiring matches the replacement before reapplying power.

This small stopper installs in the refrigerator to limit the travel of a moving component and keep it securely in place. Replacing a broken or missing stopper prevents over-extension and helps maintain smooth, aligned operation.

• Limits the range of motion for a door, bin, or drawer to prevent over-opening or accidental removal
• Helps keep interior components aligned and operating smoothly
• Replace if cracked, missing, or deformed
• Common symptoms: drawer or bin slides out too far, door swings past normal range, or a broken plastic stop is found

• Disconnect power before servicing; remove or support the affected bin/drawer/door
• Note the old stopper's orientation and location before removal
• Transfer and reuse any original screws or clips if applicable
• Snap or fasten the new stopper in place and test for smooth movement

Damper motor support secures the damper motor assembly inside the refrigerator, keeping the air-control damper aligned so it opens and closes correctly. Replacing a damaged support restores proper airflow control and reduces noise. What it does:

• Secures and positions the damper motor assembly so the air-control damper moves smoothly.
• Keeps the motor and damper aligned to help prevent rattling, grinding, or loose motor noise.
• Supports consistent airflow between compartments to assist with even cooling.
• Resolve damper movement problems like the damper not opening or closing fully.

• Disconnect power to the appliance before starting work; remove food and shelves as needed for access.
• Remove the interior access panel to reach the damper assembly; handle plastic tabs and clips gently to avoid breakage.
• Align the motor and damper during reassembly and secure all fasteners; test damper operation before replacing panels and shelving.

This water tank assembly is the refrigerator's internal reservoir that stores and delivers water to the dispenser and ice-making system, restoring proper water flow and reducing service calls for lost dispensing or poor ice production. What it does:

• Holds and routes fresh water from the household supply to the dispenser and ice maker
• Replaces cracked, warped, or leaking reservoirs that cause visible leaks or loss of water pressure
• Restores normal dispensing when the original tank is blocked, damaged, or failing
• Works with the refrigerator's water pump/valve system to maintain steady water delivery

• Disconnect refrigerator power and shut off the water supply before beginning work
• Drain remaining water from lines and tank to avoid spills; keep towels handy
• Inspect and replace any worn gaskets, hoses, or clamps for a complete seal

This replacement power control board assembly restores the electronic control for the appliance, allowing regulated power and signal management for proper operation. It replaces a failed sub control board to help recover normal function. What it does:

• Regulates power distribution and control signals to the appliance's subsystems
• Replaces a failed sub PCB that can cause intermittent or total loss of electronic control
• Resolves symptoms such as no power to circuits, unresponsive controls, or erratic operation
• Works with the appliance's main control to restore coordinated electronic control

• Disconnect power (unplug or shut off breaker) before beginning service
• Take photos of wire locations and connector orientation before disconnecting
• Handle the board carefully; avoid static discharge and do not touch components