Lmx28988st /01 Parts

This cover cap is a small plastic trim piece that protects exposed fasteners and improves the appliance's appearance. It snaps into place to hide mounting posts and help prevent snags or debris buildup. What it does:

• Covers and protects exposed screws, posts, or fasteners for a finished look
• Prevents lint, dust, and debris from collecting around the mounting point
• Reduces the chance of fabric snags or contact with sharp edges
• Restores worn or missing trim for improved cosmetics

• Disconnect power to the appliance before starting any service that exposes electrical components
• Usually installs by snapping over the post or press-fitting into the trim opening — no special tools required
• If needed, remove adjacent trim pieces to gain access, then reinstall trim in reverse order
• Inspect surrounding mounting hardware for damage and replace if necessary

This door gasket assembly seals the refrigerator/freezer door to help maintain proper temperature and reduce energy loss. It replaces a worn or damaged seal to improve cooling performance and prevent moisture buildup. What it does:

• Creates an airtight seal between the door and cabinet to keep cold air in and warm air out
• Helps prevent frost buildup, water leaks, and fluctuating internal temperatures
• Reduces compressor run time by maintaining consistent internal temperature
• Restores proper magnetic engagement where applicable to ensure the door closes fully

• Inspect the door flange for damage and clean thoroughly before installing the new gasket.
• Remove the old gasket carefully to avoid bending the door; align the new gasket evenly around the door perimeter.
• Warm the gasket slightly if needed to help seat it into the channel; avoid open flames or excessive heat.
• If the door still does not seal after installation, check hinge alignment and adjust.

This motor bracket assembly secures the appliance motor to the cabinet, keeping the motor properly positioned for reliable operation and reducing vibration or rubbing. Replaces a worn or damaged motor mounting bracket to restore stability. What it does:

• Holds the motor in place to maintain proper belt alignment and drivetrain geometry
• Prevents motor movement that can cause loud noise, grinding, or rubbing
• Reduces excessive vibration that can transfer to the cabinet or other components
• Helps maintain safe, consistent motor operation during spin or drive cycles

• Disconnect power (and gas if applicable) before starting any repair
• Support the motor before removing mounting hardware to avoid strain on wires or components
• Tighten all fasteners to OEM torque specs; replace any damaged brackets or fasteners
• Test operation after installation and re-check for proper alignment and noise

This restrainer is a small retaining clip that helps secure moving or removable components in place, reducing rattles and keeping parts aligned for reliable operation. It's a simple replacement for worn or broken clips. What it does:

• Holds a cover, panel, or door-related component in proper position to prevent shifting
• Reduces noise caused by loose or vibrating parts
• Restores original fit where a broken or missing clip allows movement
• Simple mechanical function — no electrical connections or calibration

• One restrainer

• Disconnect power (and water if applicable) before beginning repairs
• Inspect surrounding mounting points for damage; replace any broken tabs or fasteners
• Typically installs with basic hand tools; align clip and press or snap into place until secure

This ice bank door gasket is the flexible door seal that keeps the ice bin compartment closed to limit warm air and moisture intrusion. Replacing a worn or torn gasket restores a tighter seal and helps reduce frost buildup and ice clumping. What it does:

• Forms an airtight seal around the ice bank/ice bin door to help prevent warm air and moisture from entering the compartment
• Reduces frost buildup, ice clumping, and excessive condensation inside the ice bin area
• Helps stop water or drips that can occur when the door seal is cracked or deformed
• Restores even door contact for proper closing and retention of ice quality

• Disconnect power to the refrigerator and remove the ice bin and any loose items before beginning.
• Inspect the door mounting channel; clean residue and old adhesive so the new gasket seats fully.
• Press the gasket evenly into the door channel, aligning any tabs or locator features; avoid stretching the gasket excessively.
• Use only non-sharp tools to ease the gasket into place; if the model uses clips or adhesive, replace or reapply per the manufacturer's instructions.

This OEM replacement part is a cover assembly for refrigerators. The cover assembly houses the selection buttons of the refrigerator as well as the water dispenser. If the cover assembly is cracked, inoperable, or otherwise damaged, it will need to be replaced. Luckily, replacing this part is a rather simple process. To start, make sure the refrigerator is unplugged. Once unplugged, proceed to open the freezer door to remove the side panel of the freezer door. Remove the screws that attach the panel. Once they are removed, locate the mounting tabs that hold the display cover in place. Release the locking tabs and push the display cover out away from the fridge to release it. Once removed, snap the new display cover back in place and make sure that it is securely attached to the refrigerator. Reinstall the inner panel, and restore power to the appliance.This genuine replacement part is sourced directly from the manufacturer and is compatible with LG brand refrigerators.

This spanner is the specialized hand tool used to turn and hold slotted nuts, collars, or fittings on compatible appliances, making service and adjustments easier and safer. It gives a secure grip for loosening or tightening components without damaging surrounding parts. What it does:

• Fits and turns slotted or notched appliance fasteners and collars commonly used in assemblies
• Helps hold a component steady while you loosen or tighten the mating fastener
• Reduces slippage and tool marks compared with pliers or improvised tools
• Useful during maintenance tasks such as removing retaining rings, collars, or adjustable fittings

• One spanner tool

• Disconnect power and/or gas and follow all safety precautions before servicing appliances
• Use the correct size spanner engagement to avoid slipping or rounding the fastener
• Apply steady force; do not use cheater bars or excessive torque unless specified by the manufacturer

This rail guide assembly replaces a worn or broken slide rail that supports smooth movement of a drawer or component. Restores proper alignment and helps the drawer glide quietly and evenly. What it does:

• Guides and supports the drawer or sliding component along its track.
• Replaces damaged or bent rail sections that cause sticking or uneven movement.
• Reduces scraping, grinding, or noisy operation from a faulty guide.
• Helps restore proper alignment to prevent binding or partial closure.

• One rail guide assembly.

• Disconnect power (and water if applicable) and follow appliance-specific disassembly steps before replacing the rail.
• Basic hand tools are typically required; avoid forcing components to prevent breakage.
• Keep fasteners and any removed parts organized for reassembly.

This is a replacement screw designed to secure appliance components where the original customized fastener is required. It restores proper fit and stability for panels, brackets, or assemblies that use this specific fastener. What it does:

• Replaces a missing, stripped, or damaged customized screw to restore secure attachment of parts.
• Helps eliminate rattling, loose panels, or misaligned assemblies caused by a faulty fastener.
• Matches the OEM mounting point to maintain correct part alignment and function.
• Suitable where the appliance design calls for this specific customized screw type.

• Turn off and unplug the appliance before servicing to avoid shock or injury.
• Use the correct screwdriver or bit to avoid stripping the screw head; do not force.
• Keep track of small parts during disassembly and reassembly; work on a stable surface.
• If threads are damaged or the mounting hole is stripped, inspect the mating component for repair before installing the new screw.

This door basket assembly replaces a cracked or loose refrigerator door bin so you can store bottles and groceries securely on the door. It restores proper storage and keeps items from falling or shifting during use. What it does:

• Provides a stable shelf on the refrigerator door for bottles, jars and small containers
• Replaces cracked, warped or broken door bins that no longer hold items securely
• Helps stop items from falling out when the door is opened or closed
• Restores original storage capacity and organization on the door

• Remove all contents from the door and lift out the old basket; alignment tabs usually slide into molded slots
• Inspect mounting slots for damage before installing the new basket
• Press the basket into place until it snaps or seats securely; test with a light load