Lmx28988st /01 Parts

This Door Basket Assembly replaces a damaged or worn door shelf bin to restore secure storage on the appliance door and keep bottles, jars and small items contained during normal use. Fits the original mounting points for a direct replacement. What it does:

• Provides a molded shelf area that holds bottles, condiments and small containers on the door.
• Restores proper door storage if original basket is cracked, broken or bowed.
• Helps prevent items from shifting or falling when the door is opened or closed.
• Matches OEM shape and mounting locations for a straightforward swap.

• 1 door basket assembly

• Remove all items from the door and power off the appliance before beginning.
• Typically installs by aligning the basket with the door rails or mounting tabs and snapping or sliding into place.
• Inspect mounting tabs and surrounding trim for damage; replace any broken hardware before installing.
• Use gloves to avoid sharp edges and discard broken plastic parts safely.

This door gasket assembly replaces a damaged or worn refrigerator door seal to restore an airtight closure and improve cooling efficiency. It fits the door and provides a continuous seal to help maintain consistent internal temperature. What it does:

• Seals the refrigerator door to prevent warm air from entering and cold air from escaping.
• Helps reduce frost buildup and excessive compressor run time caused by a failed seal.
• Addresses symptoms like visible gaps, torn or deformed rubber, and poor door closure.
• Restores proper door alignment and contact for even cooling across compartments.

• One door gasket assembly

• Disconnect power and remove stored items from the door before starting.
• Replace gasket by removing retaining clips or trim, seat new gasket fully into the channel, and reattach trim/clips per manufacturer guidance.
• Avoid sharp tools that can damage the gasket; warm the gasket slightly if needed for easier seating.
• After installation, allow the gasket to set and check the door seal on all sides; adjust alignment if necessary.

The Control Board is an OEM component specifically designed for LG bottom-freezer refrigerators. Located within the electrical control housing, this printed circuit board directs critical operations like cooling fans, temperature sensors, and ice/water dispensers. Precise microchip programming optimizes food freshness.

Causes of a bad control board can include moisture damage deteriorating circuits over time, electrical failures inhibiting components, or loose connections preventing communications. Without directing key systems appropriately, the refrigerator cannot efficiently cool food or regulate temperatures.

Symptoms of a bad control board include: 

• Abnormal cooling and frosting within the refrigerator compartment
• Inability to adjust temperature settings  
• Malfunctioning ice/water dispensers or cooling vents
• Diagnostic error codes appearing

This LG OEM replacement ensures dependable performance through consistent and long-lasting operation. Compatible also with Kenmore bottom-freezer models, it restores full functionality through seamless repairs.

This replacement freezer tray holds water to form ice and fits into the freezer compartment to restore ice production and keep cubes contained. It's a simple swap that brings back reliable ice-making without tools. What it does:

• Holds water in molded cavities so ice cubes form evenly
• Replaces cracked, warped, or missing trays that leak or fail to produce ice
• Keeps ice contained and easier to remove from the freezer
• Helps prevent spills and pooling inside freezer shelves

• Remove the old tray, clean the cavity area, and slide or set the new tray into place per your freezer's shelf layout
• Wash the tray with warm, soapy water and rinse before first use
• Do not use sharp tools to pry ice from the tray; twist gently or run under cold water to release cubes
• Keep away from direct heat or stovetop surfaces and avoid using abrasive cleaners

This is a replacement mounting bolt used to secure appliance components and assemblies, restoring proper fit and reducing movement that can cause noise or misalignment. Use when a factory fastener is missing or damaged. What it does

• Fastens panels or internal components to maintain correct alignment and structural integrity.
• Prevents vibration-related noise and rubbing by holding parts securely in place.
• Restores secure connections after disassembly for service or repair.
• Helps eliminate intermittent movement that can lead to wear or leaks when a fastener is compromised.

• Use the correct bolt length and thread engagement for the application; do not force a mismatched fastener.
• Tighten to snug, manufacturer-specified torque when available; avoid overtightening to prevent stripping.
• Inspect surrounding parts (washers, nuts, threaded holes) and replace if worn or damaged.
• Disconnect power and follow all safety precautions before servicing the appliance.

This replacement customized screw secures internal panels and components to restore proper fit and reduce movement. A small but essential fastener for repairs that stop rattling and prevent loose parts from causing damage. What it does:

• Fastens panels, brackets, or trim so parts stay aligned and stable
• Stops vibration-related noise caused by loose fasteners
• Helps prevent parts from shifting or falling during operation
• Replaces stripped or missing screws to restore proper assembly

• Disconnect power before servicing the appliance to avoid shock or injury
• Use the correct screwdriver or driver bit to prevent stripping the head
• Tighten until snug—do not overtighten, which can strip threads or crack components
• Inspect mating threads and replace if damaged; replace only with the exact OEM screw