Lmxs26726s Parts

This connector tube provides a sealed water path between refrigerator water components to restore proper water flow and reduce leaks. It's a direct-fit replacement when your existing connector is cracked, clogged, or damaged. What it does

• Re-establishes a secure water connection between dispenser/ice-making components.
• Restores water flow so the ice maker and dispenser can fill properly.
• Prevents drips and leaks from damaged or degraded tubing joints.
• Helps eliminate intermittent filling or reduced water flow caused by collapsed tubing.

• One connector tube.

• Disconnect power and shut off the water supply before beginning any work.
• Use proper fittings or clamps and tighten securely—avoid over-tightening plastic fittings.
• After installation, turn on the water and check all connections for leaks; discard any damaged or brittle tubing.

This damper motor support replaces a broken or warped mount for the refrigerator's air damper assembly. It holds the damper motor and door securely so the system can meter freezer air into the fresh food compartment.

• Secures and aligns the air damper motor/door within the duct
• Helps ensure proper opening/closing of the damper to regulate airflow and temperature
• Damage can contribute to a warm or too-cold refrigerator and inconsistent temperatures
• May cause clicking or buzzing from the damper area or a visibly loose assembly

• Disconnect power to the refrigerator before servicing
• Access the damper behind the fresh food compartment duct/cover; remove shelves as needed
• Note wiring and orientation; transfer the existing damper motor and door to the new support and reuse fasteners
• Ensure the door moves freely and seals before reassembly; restore power and verify airflow

Replacement drain tube assembly that directs wastewater from the appliance tub to the drain pump, restoring proper drainage and helping reduce leaks. Use when the original tube is cracked, kinked, clogged, or visibly leaking. What it does

• Channels wastewater from the tub to the drain/pump for normal draining.
• Maintains a sealed path to help prevent water leaks under or around the appliance.
• Replace when you see pooling water, slow or no drain, or visible damage to the tube.
• Works as the fluid conduit; does not include clamps or pump.

• Disconnect power and water supply before beginning any service.
• Route the tube along the original path and secure with existing clamps or the correct replacement fasteners.
• Avoid kinks, sharp bends, and contact with sharp edges to prevent leaks or premature wear.
• After installation, restore power/water and run a short drain cycle; check all connections for leaks.

This cover lever replaces a damaged or worn dispenser lever cover to restore a clean, functional surface for pressing the dispenser. Helps keep debris out of the lever area and supports reliable lever actuation. What it does:

• Covers and protects the dispenser lever mechanism from chips, cracks, and debris.
• Provides a smooth contact surface for pressing the dispenser to activate water/ice dispensing.
• Helps prevent leaks or improper actuation caused by broken or warped lever covers.
• Restores cosmetic appearance at the dispenser area when the original cover is cracked or missing.

• Disconnect power and shut off the water supply before beginning any work.
• Removal typically requires accessing the dispenser bezel or door panel—use basic hand tools and retain all fasteners.
• Handle clips and tabs carefully to avoid breakage; test dispenser function after reassembly.

This replacement home bar door gasket creates an airtight seal around the refrigerator's beverage/access compartment to help maintain cold temperatures and reduce drafts and moisture buildup. What it does:

• Seals the home bar/door compartment to help keep cold air in and warm air out
• Reduces condensation, frost buildup and temperature fluctuations in the compartment
• Helps prevent spoiled items and improves cooling efficiency when functioning properly
• Addresses symptoms like visible gaps, air leaks, excess moisture, or a door that won't close tightly

• Clean the door channel and gasket seating area of debris and old adhesive
• Press the gasket evenly into the channel, working around the door to ensure full contact
• Test the door for an even seal and adjust as needed; unplug refrigerator only if required for access or safety

This customized pin is a precision fastener that serves as a pivot or locating point within your appliance. It helps keep mating parts aligned and moving smoothly. Replace a bent, worn, or missing pin to restore proper operation. What it does

• Acts as a pivot/axle or locating pin between connected parts
• Maintains alignment to reduce wobble and uneven movement
• Supports smooth opening/closing or rotation at the joint
• Common signs it's needed: looseness, sagging or misalignment, scraping/squeaking at the pivot, or a visibly worn/bent/missing pin

• One customized pin

• Disconnect power (and shut off water supply, if applicable) before servicing
• Support the door/panel/assembly to remove load from the pin during removal/installation
• Note the orientation and order of any spacers, bushings, or washers and transfer them to the new pin
• Apply a light lubricant and verify smooth movement before restoring power

The Fan and Grille Assembly is an OEM component designed for LG refrigerators. This assembly circulates air within the refrigerator compartment to maintain even cooling temperatures. 

Causes of a bad fan and grille assembly can include failure of motorized fan components over time, buildup of dust or debris restricting airflow, or physical damage to fan blades.

Symptoms of a bad fan and grille assembly include:  

• Development of warm spots within the fridge
• Excessive frost or ice buildup inside 
• Louder than normal operating sounds
• Inability to maintain proper temperature settings

Replace yours today with this genuine OEM LG assembly to restore optimized air circulation for balanced cooling. This replacement assembly is compatible with Kenmore, Frigidaire, and GE refrigerator models. Proper airflow is essential for energy efficiency and food freshness.

Refrigerator door handle assembly that restores a secure grip and reliable door operation. Ideal replacement for handles that are cracked, loose, or missing, helping the door open and close smoothly and safely. What it does

• Provides a sturdy grip for opening and closing the refrigerator door.
• Replaces cracked, chipped, broken or loose handles that make the door difficult to operate.
• Restores proper handhold to help prevent slips and accidental drops when accessing the fridge.
• Designed to line up with factory mounting points for a straightforward replacement.

• For safety, unplug the refrigerator or switch off power at the breaker before starting if removal requires access near electrical components.
• Keep original mounting screws and trim; many handle assemblies reuse existing hardware.
• Use basic hand tools (screwdriver, nut driver) and steady support for the door during installation; get assistance if the door is heavy or awkward to handle.

Replacement wiring harness that connects power and control signals between appliance components to restore reliable electrical connections and reduce intermittent operation, error codes, or complete component loss of power. What it does:

• Routes power and signal wires between control boards, motors, sensors, and other components.
• Restores reliable electrical continuity when a damaged harness causes intermittent operation or no power to a component.
• Can stop symptoms such as appliance not starting, error codes tied to wiring faults, or components that run intermittently.
• Replaces harnesses with visible damage, burned connectors, or broken/loose terminals.

• Disconnect power (and water, if applicable) before attempting any service.
• Inspect connectors and routing; replace damaged clips or grommets to prevent chafing.
• Match connector shapes and pin counts; do not force connectors together.

This small retaining clip secures its mating component within the refrigerator assembly, keeping parts properly seated and reducing vibration. Replacing a damaged or missing clip helps restore a snug fit and reliable operation of the attached piece.

• Holds the designated part firmly in place within the assembly
• Maintains proper alignment to prevent movement or rattling
• Helps ensure panels, ducts, or lines stay secured during use
• Symptoms can include loose or sagging parts, vibration noises, or components that won't stay attached

• Disconnect power; if working near the water system, also shut off the water supply
• Note the original orientation and placement before removal
• Fully seat the mating component, then press the new clip into place without forcing
• Check operation before reassembly

This small stopper installs in the refrigerator to limit the travel of a moving component and keep it securely in place. Replacing a broken or missing stopper prevents over-extension and helps maintain smooth, aligned operation.

• Limits the range of motion for a door, bin, or drawer to prevent over-opening or accidental removal
• Helps keep interior components aligned and operating smoothly
• Replace if cracked, missing, or deformed
• Common symptoms: drawer or bin slides out too far, door swings past normal range, or a broken plastic stop is found

• Disconnect power before servicing; remove or support the affected bin/drawer/door
• Note the old stopper's orientation and location before removal
• Transfer and reuse any original screws or clips if applicable
• Snap or fasten the new stopper in place and test for smooth movement

Damper motor support secures the damper motor assembly inside the refrigerator, keeping the air-control damper aligned so it opens and closes correctly. Replacing a damaged support restores proper airflow control and reduces noise. What it does:

• Secures and positions the damper motor assembly so the air-control damper moves smoothly.
• Keeps the motor and damper aligned to help prevent rattling, grinding, or loose motor noise.
• Supports consistent airflow between compartments to assist with even cooling.
• Resolve damper movement problems like the damper not opening or closing fully.

• Disconnect power to the appliance before starting work; remove food and shelves as needed for access.
• Remove the interior access panel to reach the damper assembly; handle plastic tabs and clips gently to avoid breakage.
• Align the motor and damper during reassembly and secure all fasteners; test damper operation before replacing panels and shelving.

This evaporator assembly replaces the freezer evaporator coil and housing to restore proper cold-air circulation and frost control in the freezer compartment. It helps re-establish normal cooling and defrost performance when the evaporator is damaged or leaking. What it does:

• Contains the evaporator coil and housing that absorb heat from the freezer compartment
• Enables proper airflow and heat transfer for consistent freezer temperatures
• Restores defrost cycle effectiveness when a cracked or corroded evaporator causes frost build-up
• Addresses symptoms like excessive frost/ice on the coil, reduced cooling, or water leaking inside the freezer

• Disconnect power to the appliance before starting any repair; follow manufacturer safety instructions
• Replacement typically requires removing interior liners and thawing any ice; handle fins and tubing carefully to avoid damage
• Use proper sealing/insulation when reinstalling the housing to prevent air leaks and frost issues

The Fan Guide Assembly is an OEM component specifically designed for LG refrigerators equipped with rear evaporator fans. This assembly guides proper airflow within the refrigerator compartment.

Symptoms of a bad fan guide assembly include:

• Development of warm or cool spots inside fridge surfaces  
• Excessive frost or moisture buildup at specific locations
• Reduced temperature fluctuation stability 
• Abnormally loud fan operation sounds

Causes of failure can be damage allowing fan blade strikes, cracks reducing structural integrity over time, or accumulation of dust clogging air passages.  

Replace yours today with this genuine OEM LG assembly to maintain optimized cooling throughout storage areas. Smooth, balanced airflow preserves food freshness evenly. This replacement part is compatible with Frigidaire, GE, and Samsung models for factory fit and function. Proper air distribution helps maintain energy efficiency.

This center door hinge assembly replaces the pivot that lets a refrigerator door open and close smoothly, restoring proper door alignment and sealing. Designed to fit OEM mounting points for reliable operation and long-term use. What it does:

• Supports the center door pivot and maintains proper door alignment
• Enables smooth opening and closing of the affected door section
• Helps maintain an effective door seal to prevent cold air loss
• Commonly used when the door sags, binds, or makes noise at the hinge

• 1 center hinge assembly

• Installation requires removing the door and supporting it to prevent damage or injury
• Tighten mounting fasteners to the manufacturer's torque specifications; avoid over-tightening
• Disconnect power to the appliance and follow all safety precautions before beginning work

This upper hinge assembly secures and allows the refrigerator door to pivot smoothly, restoring proper door alignment and sealing. It replaces worn or damaged upper hinge hardware to stop sagging or uneven door movement. What it does:

• Supports the top of the refrigerator door and provides the pivot point for opening and closing
• Restores proper door alignment and helps the door form a tight seal when closed
• Stops symptoms such as a sagging or tilted door, door rubbing, or uneven movement
• Durable metal/plastic construction resists wear from regular use

• One upper hinge assembly

• Unplug the appliance or disconnect power before starting work
• Support the door before removing the hinge to prevent it from falling
• Reuse any original screws/fasteners only if undamaged; replace damaged fasteners