Lmxs28596s /01 Parts

An in-line union for appliance tubing, this tube connector joins two sections of plastic line to create a secure, leak-resistant connection in the water circuit, ideal for restoring flow after a repair, trim, or reroute. What it does:

• Connects two lengths of compatible plastic tubing to form a continuous run
• Helps maintain proper water delivery through the appliance's water system
• Can address leaks, drips, or loose/failed connections at a splice point
• Useful when replacing, shortening, or rerouting tubing during service

• 1 tube connector

• Disconnect power and shut off the water supply before servicing
• Cut tubing square; ensure ends are clean, round, and free of gouges
• Insert tubing fully into the connector until seated, then perform a gentle pull test
• Restore water and inspect all joints for leaks; use the connector size that matches your tubing's outer diameter

This center hinge assembly supports the refrigerator door at the mid-hinge position and allows smooth, reliable pivoting. Replacing a worn hinge restores proper alignment so the door closes and seals as designed.

• Provides the pivot point at the center hinge location
• Supports door weight to maintain alignment and clearance
• Helps ensure even gasket contact for an effective seal
• Common symptoms: door sagging or rubbing, squeaking at the hinge, difficulty closing, visible play or damage at the hinge pin

• Unplug the appliance and remove items from the door to reduce weight
• Support the door while removing the center hinge fasteners
• Note and transfer any spacers/washers in the same order and orientation
• After installation, align the door and verify the gasket seals evenly

This freezer door foam assembly replaces the insulating foam inside a freezer door to help restore the door's sealed fit and reduce air leakage. It helps improve temperature stability and reduces frost buildup when the existing foam is damaged. What it does:

• Replaces deteriorated or compressed insulation inside the freezer door
• Restores a tighter door seal to reduce warm air infiltration
• Helps reduce excessive frost or ice buildup caused by air leaks
• Supports consistent freezer temperatures and efficient operation

• Disconnect power before starting and work with the door supported or removed to avoid injury.
• Remove the inner door panel or liner carefully to access the foam; keep fasteners and clips organized.
• Fit the foam into the door cavity without overstretching; ensure even contact with mating surfaces for a proper seal.
• If adhesive, clips, or a door liner are required, replace or reinstall them as needed.

This tray cover replaces a damaged or missing appliance tray cover to restore a clean appearance and proper containment of spills. It fits into the existing tray location and helps keep interior surfaces protected during normal use. What it does:

• Covers the appliance tray to help contain spills, crumbs, and minor debris
• Maintains a finished look and helps prevent direct contact with the underlying tray
• Supports proper placement of removable trays or components that sit above it
• Useful when the original cover is cracked, warped, or otherwise compromised

• One replacement tray cover

• Basic snap-in or screw-in installation; confirm orientation before fastening
• Power off and unplug the appliance before attempting any service
• Use gentle pressure to avoid cracking the new cover; do not force damaged fasteners
• Replace missing or damaged screws or clips with OEM-specified hardware

This is a replacement filter cover that secures the air filter in place and protects internal components. It restores the proper fitment of the filter and helps maintain intended airflow and filtration performance. What it does:

• Holds the air filter securely so air passes through the filter media as designed
• Protects internal components from dust and debris
• Prevents gaps that can reduce filtration efficiency or allow unfiltered air bypass
• Helps reduce rattling or vibration caused by a loose or damaged cover

• One filter cover

• Disconnect power before accessing internal parts
• Remove the old cover by releasing retaining tabs or fasteners and align new cover until it snaps or locks into place
• Inspect nearby seals and the filter; replace if damaged
• Handle plastic parts gently to avoid cracking; do not force into place

This button assembly is the user interface component that replaces worn or unresponsive control buttons on the appliance control panel, restoring normal button feedback and selection control for cycles and features. What it does:

• Provides the tactile/button contact surface for the appliance control panel so button presses register correctly
• Restores proper input for cycle selection, start/pause, and option buttons when original buttons are damaged or worn
• Can resolve symptoms like unresponsive or sticking buttons and intermittent button activation
• Works as the direct replacement part designed to fit the OEM control overlay and button housing

• One button assembly as shown

• Disconnect power to the appliance before starting any repair to avoid shock or unintended operation
• Access may require removing the control panel or console; handle the control ribbon/cable and plastic tabs carefully to avoid damage
• Keep small screws and clips organized; test button operation before reassembling fully

This door gasket assembly replaces a worn or damaged refrigerator door seal to help restore an airtight seal and maintain proper cooling. A properly seated gasket reduces drafts, moisture intrusion, and energy loss. What it does:

• Seals the refrigerator door to keep cold air in and warm air out.
• Helps prevent frost buildup and moisture accumulation inside the compartment.
• Reduces compressor run time and energy usage caused by a leaking seal.
• Addresses symptoms such as warm spots, visible gaps around the door, or condensation on the door edges.

• Disconnect power to the appliance and remove food from the door area before starting.
• Inspect the door flange for damage and clean the mounting surface to ensure a proper seal.
• Seat the gasket fully into the channel; some models require loosening or removing trim screws to install.
• If the door does not close evenly after installation, check hinge alignment and adjust per the OEM instructions.

A replacement rail guide assembly that restores smooth, stable sliding for refrigerator/freezer drawers and shelves. Helps reduce sticking and misalignment so drawers open and close more reliably. What it does:

• Guides drawer or shelf movement along the rail for smooth sliding
• Helps keep drawers aligned and prevents binding or tipping
• Reduces noise and catching when opening or closing drawers
• Restores proper support for heavy or loaded drawers

• Disconnect power or unplug appliance before accessing drawers or internal components
• Remove affected drawer or shelf to access mounting points
• Inspect mounting clips and screws; reuse only undamaged hardware or replace as needed
• Test drawer operation after installation to ensure proper alignment and secure fit

This lever return spring restores proper tension to the lever assembly so the control or latch returns smoothly. A direct-fit replacement designed to restore normal lever movement and function. What it does:

• Provides return tension for the lever to ensure reliable latch or control movement
• Helps stop the lever from sticking or remaining engaged after use
• Restores smooth, consistent operation when the original spring is worn or broken
• Commonly replaced when lever movement feels loose or fails to return

• One spring lever

• Disconnect power (or unplug) and follow appliance safety procedures before servicing
• Access may require removing panels or the control/door assembly; keep fasteners organized
• Inspect mating lever and pins for wear; replace damaged components to prevent repeat failure

This door assembly replaces the outer door for the refrigerator's built-in home bar compartment, restoring a proper seal and appearance so the bar area closes and insulates correctly. Designed to match OEM fit and function. What it does:

• Replaces a damaged, dented, or warped home bar door to restore proper closure
• Helps maintain interior temperature of the bar compartment by ensuring a good seal
• Resolves issues with the door not latching or sitting flush
• Restores original appearance and finish of the bar access area

• One complete home bar door assembly

• Professional or experienced DIY recommended—door assemblies can be heavy and awkward to handle
• Disconnect power to the appliance before starting any repairs
• Keep fasteners and hinge hardware organized; follow OEM alignment for correct sealing

This upper hinge assembly secures and guides the appliance door at the top hinge point, restoring proper door alignment and smooth opening. Replaces a worn or damaged upper hinge to reduce door sag, binding, or uneven sealing. What it does:

• Supports the top of the door and provides the pivot point for opening and closing
• Restores correct door alignment to improve gasket sealing and energy efficiency
• Eliminates rubbing, binding, or uneven movement caused by a damaged hinge
• Reduces noise from a loose or worn hinge

• Unplug the appliance and empty or support the door before starting work
• Use proper hand tools and take care not to tighten fasteners excessively
• Keep track of hardware; replace only listed items unless additional parts are required

This PTC thermistor assembly senses temperature and sends a signal to the appliance control so the unit runs at the correct temperature. Replacing a faulty thermistor restores reliable temperature feedback for proper operation. What it does:

• Monitors temperature and provides feedback to the appliance control board
• Helps control cooling/heating cycles by changing resistance with temperature
• Common symptom of failure: incorrect temperature readings or improper cycling
• May also cause extended run times, frequent on/off cycling, or no cooling

• Disconnect power to the appliance before starting any repair
• Handle the sensor and wiring gently; avoid kinks or sharp bends in the thermistor lead
• Test operation after installation and reassemble panels securely