Lmxs28626 Parts

This door foam assembly is the molded insulation that sits inside a refrigerator door to help maintain cold temperatures and reduce condensation. Replacing damaged or compressed foam restores the door's insulating barrier and helps the refrigerator run as intended. What it does:

• Replaces the factory foam core that fills the inner door cavity and supports door liners.
• Restores insulation where old foam is cracked, crushed, or missing.
• Helps reduce frost buildup and interior temperature fluctuations caused by damaged door insulation.
• Supports proper seal and liner spacing to help the door close and perform correctly.

• One door foam assembly

• Disconnect power to the appliance before beginning any repair.
• Installation typically requires removing the door liner/panel and any internal components attached to the liner; handle clips and connectors carefully.
• Use appropriate hand tools and take care not to puncture the foam or damage the door liner; replace any damaged adhesive or retainer clips.

This guide assembly positions and secures the TV's front-panel or bezel components to keep controls and trim aligned for a clean fit and reliable button access. Replaces a worn, cracked, or misaligned guide to restore proper panel seating. What it does

• Aligns and supports the TV front panel/bezel so edges meet evenly
• Holds control board/buttons or trim in the correct location
• Prevents rubbing, rattling, or gaps between bezel and chassis
• Helps maintain consistent button feel and keypad alignment

• One guide assembly

• Unplug the TV and place on a soft, stable surface before beginning
• Remove bezel or trim per service manual to access guide locations
• Keep small screws and clips organized; compare old part orientation to new

This lower door hinge assembly supports and pivots the appliance door for smooth opening and reliable closing. Replacing a worn or damaged lower hinge restores proper door alignment and sealing. What it does:

• Provides the pivot point for the bottom of the door so it opens and closes correctly
• Stabilizes door alignment to prevent sagging or uneven gaps
• Helps maintain a consistent seal to preserve internal temperature
• Stops grinding, scraping, or noisy hinge movement when worn

• One lower hinge assembly

• Disconnect power and remove contents as needed; support the door before removing the hinge
• Remove mounting fasteners and transfer any pins or bushings if they remain reusable; install the new hinge in the original orientation
• Reinstall and tighten mounting fasteners, then check door alignment and operation; adjust as needed
• If the door is heavy, have a second person assist to avoid injury or damage

This stopper assembly cushions and limits the door travel to prevent slamming and ensure correct door alignment. It restores smooth, controlled closing and helps reduce noise and wear on the door hinge area. What it does:

• Absorbs door impact to prevent hard slams and reduce noise
• Keeps the door from overtravel for consistent alignment
• Helps protect hinge and cabinet edges from damage
• Restores proper door closing feel when worn or broken

• One stopper assembly as shown

• Disconnect power and empty door area before starting repairs
• Access may require removing door trim or inner panel
• Use basic hand tools; avoid forcing the part into place to prevent damage

This drawer tray assembly replaces a damaged or worn refrigerator storage drawer to restore stable storage and smooth operation. It supports food storage and helps the drawer open and close as designed. What it does:

• Replaces cracked, warped, or broken drawer tray that no longer supports items
• Restores proper seating and alignment so the drawer slides smoothly
• Prevents items from falling through or catching on damaged edges
• Helps maintain internal organization and usable refrigerator space

• Disconnect power to the appliance before servicing to avoid injury
• Handle the tray carefully to avoid damage to plastic edges or clips
• Remove any contents and existing drawer components before installing
• If the drawer uses mounting clips or rails, inspect and replace damaged hardware as needed for proper fit

This DC motor assembly powers the appliance's indoor fan to move air where needed. Replacing a worn motor restores proper airflow and reduces noise, helping the appliance maintain performance and temperature control. What it does:

• Spins the indoor fan/blower to circulate air through the appliance
• Restores airflow when a motor has failed or stopped running
• Reduces whining, grinding, or irregular fan noise caused by a faulty motor
• Helps resolve uneven temperatures or poor circulation tied to a bad motor

• Disconnect power to the appliance before starting any repair
• Handle wiring connectors and mounting tabs carefully; match harness connections exactly
• Inspect and secure mounting screws and blower/fan alignment during reassembly
• Test operation after installation to ensure proper airflow and sound

A small protective cap that covers and protects a component connection or opening from dirt and moisture, helping maintain proper function and prolong component life. Simple replacement when the original cap is cracked, missing, or worn. What it does:

• Covers exposed fittings, terminals, or openings to keep out debris and moisture
• Helps prevent leaks or contamination at the sealed connection
• Restores a secure fit when the original cap is cracked, split, or degraded
• Commonly used where a small, removable protective seal is required

• Inspect mating surface and surrounding gasket/seal before installing; replace other damaged parts as needed
• Press the cap firmly into place until fully seated; no special tools usually required
• Wear gloves and disconnect power or water supply if working near energized or pressurized components

This connector tube routes water from the refrigerator's supply to the ice maker or dispenser, restoring normal water flow and ice production when the original tube is cracked or clogged. It's a direct-fit replacement designed for quick restoration. What it does:

• Replaces damaged or cracked water line routing to the ice maker or dispenser
• Restores proper water flow to prevent low ice production or slow dispensing
• Helps stop leaks caused by split or brittle tubing at connector points
• Matches OEM routing and fit to maintain reliable connection and pressure

• Disconnect the refrigerator from power and shut off the water supply before beginning.
• Drain remaining water from lines and wear gloves; connections may drip when removed.
• Inspect fittings and seals; replace O-rings or clamps if they are worn or damaged.
• Tighten connections to a snug, leak-free fit; test by turning water back on and checking for leaks.

This replacement drawer guide restores proper tracking and smooth operation to a refrigerator or freezer drawer. It helps keep the drawer aligned and reduces scraping, sticking, or uneven movement for reliable daily use. What it does:

• Guides the drawer along its track so it opens and closes smoothly
• Replaces a worn, cracked, or bent guide that can cause sticking or misalignment
• Reduces drawer rattling and scraping against the cabinet
• Helps prevent drawer drops or catching when pulling open or pushing closed

• Unplug the appliance or switch off power before servicing to avoid electrical hazards
• Remove the drawer and any screws or retaining clips holding the old guide; keep hardware if it's reusable
• Align the new guide on the track and secure with the original screws or clips; do not force parts into place
• Test the drawer operation before returning contents; recheck alignment and hardware if movement is still obstructed

This customized replacement screw secures appliance components and restores proper fit and function. It's a direct-fit fastener designed for use where the OEM specifies a tailored screw to replace a worn, stripped, or missing fastener. What it does

• Fastens panels, brackets, or assemblies that use a manufacturer-specified customized screw
• Stops rattling or loose parts caused by worn or missing hardware
• Restores secure mounting for affected components
• Matches the OEM shape and thread pattern to prevent damage when used as directed

• Disconnect power and water before starting any repair
• Use the correct screwdriver or bit to avoid stripping the head
• Install by hand initially, then tighten snugly—do not overtighten to avoid thread damage
• Keep removed hardware organized so you replace parts in their original locations

A replacement cover motor that powers the refrigerator's dispenser cover, allowing the door to open and close so you can access ice and water. Replaces a worn or failed motor to restore normal dispenser cover operation. What it does:

• Drives the dispenser cover mechanism so the cover opens when dispensing and closes when idle
• Helps keep the dispenser sealed to reduce drafts and prevent pests or debris from entering
• Stops or fails to move when worn, causing a stuck, slow, or noisy dispenser cover
• Works with the dispenser linkage and gears to coordinate cover motion with user controls

• One cover motor

• Disconnect power to the appliance before beginning any repair
• Remove dispenser trim and access panel per your model's service instructions to reach the motor
• Handle gears and linkage carefully; ensure proper alignment during reassembly and test cover operation before finishing

This cover assembly protects a control board's printed circuit board (PCB) by shielding it from dust, moisture, and accidental contact. It helps keep the PCB secured and reduces the chance of shorting or damage during normal use. What it does:

• Shields the PCB from dirt, splashes, and foreign objects that can cause shorts or corrosion
• Secures the board in place to prevent movement and stress on connectors
• Helps maintain safe separation between live circuitry and user-accessible areas
• Reduces intermittent electrical issues caused by debris or loose components

• Always disconnect power to the appliance before starting any repair
• Handle the PCB and cover with care to avoid static discharge; use proper ESD precautions if available
• Align the cover to the board and fasten using the existing mounting points; do not overtighten screws
• After installation, restore power and verify normal operation