Lmxs28626 Parts

This rail guide assembly restores smooth, stable sliding and alignment for a refrigerator drawer. It replaces worn or damaged drawer rails to help drawers open and close evenly and prevent sticking or dropping. What it does:

• Supports and guides the refrigerator drawer along its track for consistent movement
• Keeps the drawer aligned to prevent rubbing, sticking, or uneven closure
• Helps prevent the drawer from disengaging or falling out when pulled
• Reduces noise and binding caused by worn or damaged rails

• Disconnect power to the appliance or unplug before starting any repair
• Remove the drawer per your model's service instructions to access the rails
• Align the new rail assembly and secure with existing fasteners; do not force parts
• If you encounter damaged mounting points or broken fasteners, stop.

STOPPER ASSEMBLY,DOOR

Replace a worn home bar door gasket to restore a tight seal and maintain proper cooling in the home bar compartment. This replacement gasket helps prevent cold air loss, reduce condensation, and improve temperature consistency. What it does:

• Creates an airtight seal around the home bar door to keep cold air in and warm air out.
• Helps reduce frost buildup, interior condensation, and uneven temperatures.
• Restores proper door contact to improve cooling performance and reduce strain on the compressor.
• Recommended when the gasket is cracked, torn, warped, or no longer seals evenly.

• Disconnect power to the appliance before beginning any service.
• Clean the door frame and mating surface before installing the new gasket for a proper seal.
• Remove the old gasket and press the new gasket into place evenly; check that the seal is continuous around the door.

This name plate is the exterior emblem that mounts to the appliance's front panel. It replaces a missing, cracked, or faded badge to restore a clean, factory look and cover the designated trim area.

• Attaches to the outer panel to display brand/series identification
• Restores a finished appearance where the original emblem sits
• Direct replacement for a lost, damaged, or worn badge
• Typical symptoms: missing emblem, loose or broken tabs, peeling, or discoloration

• Disconnect power before servicing the appliance
• Carefully remove the old emblem; release any tabs from behind or peel away remaining adhesive
• Clean and dry the mounting surface; remove all residue for best fit
• Align with the recess/holes and press evenly until fully seated

The Cover Assembly is an OEM part for LG French door refrigerators equipped with integrated television screens. This cover protects the television when not in use.

Symptoms of a bad cover assembly include: 

• Cracked, clouded, or peeling finish reducing aesthetics
• Poor fit allowing dust entry near television components  
• Binding or getting stuck when opening and closing
• Hinges, pins, or latches weakened through repeated use

Causes of failure can be temperature cycling absorbing and releasing moisture daily, over-extension through careless opening/closing, or general wear from constant daily usage.

Replace yours today with this genuine OEM LG cover assembly to restore your refrigerator's integrated display features. A snug fit around the television combined with a durable surface protects against spills for reliable entertainment access. This replacement part is also compatible with KitchenAid, Samsung, and GE refrigerators featuring television modules.

Replacement filter assembly head that holds and seals the refrigerator water filter cartridge and routes water to the dispenser and ice maker. Replaces damaged or worn filter heads to restore proper filter seating and help prevent leaks. What it does:

• Secures and aligns the water filter cartridge so the filter can seat and seal correctly.
• Channels water from the filter to the dispenser and ice maker.
• Stops leaks and drips caused by cracked, warped, or damaged filter head components.
• Restores proper water flow where a broken filter head was causing reduced or no water dispense.

• One filter assembly head.

• Turn off the refrigerator water supply and dispense water to relieve pressure before replacing.
• Remove the old filter and head per your owner's manual; install the new head and re-seat the filter until it locks.
• Check all connections for leaks after turning the water back on; hand-tighten only and avoid over-torquing.

This rail guide assembly supports and guides a sliding drawer, bin, or rack along its track for smooth, stable movement. Replacing a worn guide restores easy operation and helps prevent sticking, wobbling, or the slide coming off the track.

• Guides and supports the sliding drawer/bin/rack on its rail
• Maintains alignment so it opens and closes smoothly
• Helps prevent binding, uneven extension, and derailment
• Typical symptoms: hard-to-open drawer, tilt or sag, squeaking/grinding, or visible cracks/warping in the guide

• Disconnect power to the appliance before servicing
• Empty and remove the drawer/bin; disengage from the tracks per your model's procedure
• Remove mounting hardware, transfer any brackets/clips from the old guide, and install the new guide in the same orientation
• Verify smooth travel and proper alignment before reloading

Roller assembly that supports the dryer drum and helps it turn smoothly. Replacing a worn roller reduces squealing, prevents drum wobble, and helps extend belt life for quieter, more reliable drying. What it does:

• Supports the drum so it rotates evenly and maintains proper alignment
• Reduces noise like squealing, grinding, or thumping caused by worn rollers
• Prevents drum wobble and uneven wear that can stress the belt and seals
• Restores smoother drum rotation for more efficient drying performance

• Always disconnect power (and gas if applicable) before servicing the appliance
• Access the drum per the service manual—front or rear panel removal may be required
• Support the drum during removal/installation to avoid belt or seal damage
• Inspect associated parts (idler, belt, glides) and test the dryer after reassembly

Power cord assembly that restores the appliance's connection to household mains. Replaces a damaged or worn cord to help stop power loss, sparking, or intermittent operation and restore a safe power feed. What it does:

• Provides the main electrical connection from the wall outlet to the appliance so internal components receive line voltage.
• Replaces cords with visible damage, frayed insulation, exposed wires, or broken plug prongs.
• Can resolve symptoms such as no power, intermittent power, sparks at the plug, or breaker trips caused by a faulty cord.
• Restores the original style of power connection and strain-relief routing for a secure fit.

• Always disconnect power at the wall before attempting service.
• Basic hand tools may be required; secure the cord firmly with the appliance's strain relief and tighten screws.

This wiring harness assembly is the factory bundle of wires and connectors that links key components inside your appliance. Replacing a damaged harness restores reliable power/signal paths and brings affected features back to normal operation.

• Distributes power and control signals between control boards, sensors, motors, heaters, valves, and lights per the original design
• Helps address symptoms such as a component not operating, intermittent or dead functions, error codes, or visible burned/melted connectors
• Replaces broken, pinched, shorted, or corroded wiring that can interrupt circuits
• OEM-style connectors and lengths support proper plug-in fit and correct routing

• Disconnect power before servicing; do not rely on the appliance's power button
• Photograph/label each connection and note the original wire routing before removal
• Route the new harness exactly along the original path and secure in clips to prevent pinching, chafing, or heat contact
• Fully seat connectors; avoid pulling on wires when disconnecting or installing

Replacement lamp cover that protects and diffuses an appliance's interior light, restoring even illumination and shielding the bulb from spills and contact. Restores proper light output and appearance after a cracked or missing lens. What it does:

• Protects the interior light bulb from food splatter, grease, and accidental contact.
• Diffuses and evens interior illumination to reduce hot spots and glare.
• Replaces cracked, yellowed, or missing lenses that can cause dim, flickering, or exposed-bulb issues.
• Matches the original lamp housing shape and secures with the appliance's existing clips or screws.

• Always disconnect power (unplug appliance or switch off circuit) and allow the bulb to cool before beginning.
• Remove any retaining screws or clips carefully; handle the cover gently to avoid cracking.
• Seat the cover securely in the lamp housing and reinstall original hardware—do not overtighten screws.
• After installation, restore power and verify the light operates and the cover is properly seated.

This damper motor support replaces a broken or warped mount for the refrigerator's air damper assembly. It holds the damper motor and door securely so the system can meter freezer air into the fresh food compartment.

• Secures and aligns the air damper motor/door within the duct
• Helps ensure proper opening/closing of the damper to regulate airflow and temperature
• Damage can contribute to a warm or too-cold refrigerator and inconsistent temperatures
• May cause clicking or buzzing from the damper area or a visibly loose assembly

• Disconnect power to the refrigerator before servicing
• Access the damper behind the fresh food compartment duct/cover; remove shelves as needed
• Note wiring and orientation; transfer the existing damper motor and door to the new support and reuse fasteners
• Ensure the door moves freely and seals before reassembly; restore power and verify airflow

This cover lever replaces a damaged or worn dispenser lever cover to restore a clean, functional surface for pressing the dispenser. Helps keep debris out of the lever area and supports reliable lever actuation. What it does:

• Covers and protects the dispenser lever mechanism from chips, cracks, and debris.
• Provides a smooth contact surface for pressing the dispenser to activate water/ice dispensing.
• Helps prevent leaks or improper actuation caused by broken or warped lever covers.
• Restores cosmetic appearance at the dispenser area when the original cover is cracked or missing.

• Disconnect power and shut off the water supply before beginning any work.
• Removal typically requires accessing the dispenser bezel or door panel—use basic hand tools and retain all fasteners.
• Handle clips and tabs carefully to avoid breakage; test dispenser function after reassembly.

This customized pin is a precision fastener that serves as a pivot or locating point within your appliance. It helps keep mating parts aligned and moving smoothly. Replace a bent, worn, or missing pin to restore proper operation. What it does

• Acts as a pivot/axle or locating pin between connected parts
• Maintains alignment to reduce wobble and uneven movement
• Supports smooth opening/closing or rotation at the joint
• Common signs it's needed: looseness, sagging or misalignment, scraping/squeaking at the pivot, or a visibly worn/bent/missing pin

• One customized pin

• Disconnect power (and shut off water supply, if applicable) before servicing
• Support the door/panel/assembly to remove load from the pin during removal/installation
• Note the orientation and order of any spacers, bushings, or washers and transfer them to the new pin
• Apply a light lubricant and verify smooth movement before restoring power

Refrigerator door handle assembly that restores a secure grip and reliable door operation. Ideal replacement for handles that are cracked, loose, or missing, helping the door open and close smoothly and safely. What it does

• Provides a sturdy grip for opening and closing the refrigerator door.
• Replaces cracked, chipped, broken or loose handles that make the door difficult to operate.
• Restores proper handhold to help prevent slips and accidental drops when accessing the fridge.
• Designed to line up with factory mounting points for a straightforward replacement.

• For safety, unplug the refrigerator or switch off power at the breaker before starting if removal requires access near electrical components.
• Keep original mounting screws and trim; many handle assemblies reuse existing hardware.
• Use basic hand tools (screwdriver, nut driver) and steady support for the door during installation; get assistance if the door is heavy or awkward to handle.

Replacement wiring harness that connects power and control signals between appliance components to restore reliable electrical connections and reduce intermittent operation, error codes, or complete component loss of power. What it does:

• Routes power and signal wires between control boards, motors, sensors, and other components.
• Restores reliable electrical continuity when a damaged harness causes intermittent operation or no power to a component.
• Can stop symptoms such as appliance not starting, error codes tied to wiring faults, or components that run intermittently.
• Replaces harnesses with visible damage, burned connectors, or broken/loose terminals.

• Disconnect power (and water, if applicable) before attempting any service.
• Inspect connectors and routing; replace damaged clips or grommets to prevent chafing.
• Match connector shapes and pin counts; do not force connectors together.