Lmxs28996d Parts

This lever return spring restores proper tension to the lever assembly so the control or latch returns smoothly. A direct-fit replacement designed to restore normal lever movement and function. What it does:

• Provides return tension for the lever to ensure reliable latch or control movement
• Helps stop the lever from sticking or remaining engaged after use
• Restores smooth, consistent operation when the original spring is worn or broken
• Commonly replaced when lever movement feels loose or fails to return

• One spring lever

• Disconnect power (or unplug) and follow appliance safety procedures before servicing
• Access may require removing panels or the control/door assembly; keep fasteners organized
• Inspect mating lever and pins for wear; replace damaged components to prevent repeat failure

This case assembly houses the appliance's printed circuit board and provides the mounting, connection points, and protective enclosure needed for the control electronics to operate reliably. It helps keep the board secure and wired to the rest of the appliance. What it does:

• Holds and protects the control PCB from physical damage and contamination
• Provides the connector ports and wiring paths for power, sensors, and user controls
• Restores proper mechanical mounting when cracked, warped, or broken
• Common symptoms: control panel loose, intermittent power or communication, visible case damage

• Disconnect power at the breaker or unplug the appliance before starting
• Handle the PCB with care and avoid static discharge; use ESD protection if available
• Match and reconnect all wiring harnesses and secure mounting screws; do not force connectors

This hinge cover assembly replaces a damaged or missing trim piece that protects and conceals the appliance hinge, restoring a clean appearance and preventing fabric or items from catching. It's a direct-fit cosmetic and protective cover. What it does:

• Covers and protects the hinge area to prevent snagging and wear on clothing or items
• Conceals hinge mechanisms for a finished appearance
• Helps keep dirt and debris out of the hinge area
• Restores proper alignment of exterior trim when the original is cracked or broken

• One hinge cover assembly

• Disconnect power (and gas/water if applicable) before starting any repair
• Typical installation requires removing the outer panel or door access screws to reach the hinge; keep track of fasteners
• Handle plastic trim carefully to avoid cracking; use non-marring tools where possible

This door assembly replaces the outer door for the refrigerator's built-in home bar compartment, restoring a proper seal and appearance so the bar area closes and insulates correctly. Designed to match OEM fit and function. What it does:

• Replaces a damaged, dented, or warped home bar door to restore proper closure
• Helps maintain interior temperature of the bar compartment by ensuring a good seal
• Resolves issues with the door not latching or sitting flush
• Restores original appearance and finish of the bar access area

• One complete home bar door assembly

• Professional or experienced DIY recommended—door assemblies can be heavy and awkward to handle
• Disconnect power to the appliance before starting any repairs
• Keep fasteners and hinge hardware organized; follow OEM alignment for correct sealing

This upper hinge assembly secures and guides the appliance door at the top hinge point, restoring proper door alignment and smooth opening. Replaces a worn or damaged upper hinge to reduce door sag, binding, or uneven sealing. What it does:

• Supports the top of the door and provides the pivot point for opening and closing
• Restores correct door alignment to improve gasket sealing and energy efficiency
• Eliminates rubbing, binding, or uneven movement caused by a damaged hinge
• Reduces noise from a loose or worn hinge

• Unplug the appliance and empty or support the door before starting work
• Use proper hand tools and take care not to tighten fasteners excessively
• Keep track of hardware; replace only listed items unless additional parts are required

This holder assembly bracket secures and aligns a small appliance component so it stays in place during normal use, restoring reliable fit and reducing noise or movement caused by a loose part. What it does

• Provides a stable mounting point for the associated component to prevent shifting or detachment
• Restores correct alignment for doors, panels, or internal modules that rely on the bracket
• Helps stop rattling, vibration noise, or intermittent contact caused by a broken or bent bracket
• Supports safe operation by keeping parts properly positioned within the appliance

• Basic hand tools are usually all that's required; follow the appliance service manual for access steps
• Disconnect power (and water, if applicable) before starting any repairs to avoid shock or injury
• Inspect adjacent fasteners and mounting surfaces; replace any stripped screws or damaged clips for a secure fit

This Drawer Tray Assembly replaces a damaged or worn crisper/produce drawer to restore storage and organization in your refrigerator. It provides a stable surface for fruits and vegetables and helps keep produce contained and ventilated. What it does:

• Replaces a cracked, warped or broken crisper/produce drawer tray
• Restores smooth sliding and proper seating in the refrigerator drawer cavity
• Helps contain spills and keeps produce organized
• Supports normal airflow/venting designed for the drawer area

• Unplug the refrigerator or disconnect power before servicing
• Remove the old drawer by pulling out and lifting to disengage; align new tray with rails and slide into place
• Check for proper seating and smooth operation after installation

This PTC thermistor assembly senses temperature and sends a signal to the appliance control so the unit runs at the correct temperature. Replacing a faulty thermistor restores reliable temperature feedback for proper operation. What it does:

• Monitors temperature and provides feedback to the appliance control board
• Helps control cooling/heating cycles by changing resistance with temperature
• Common symptom of failure: incorrect temperature readings or improper cycling
• May also cause extended run times, frequent on/off cycling, or no cooling

• Disconnect power to the appliance before starting any repair
• Handle the sensor and wiring gently; avoid kinks or sharp bends in the thermistor lead
• Test operation after installation and reassemble panels securely

This button lever is the small control-panel actuator that transfers finger pressure to the underlying switch, restoring reliable button feel and control response. Replaces worn, cracked, or missing levers to make front-panel buttons usable again. What it does

• Acts as the actuator for a specific control-panel push button, transferring user press to the switch beneath.
• Restores button engagement when the original lever is cracked, broken, or has fallen off.
• Helps eliminate intermittent or non-responsive button presses caused by damaged actuators.
• Fits into the control-bezel and aligns the button with the switch for consistent operation.

• One button lever/actuator as shown.

• Disconnect power (unplug or shut off breaker) before servicing to avoid shock or accidental activation.
• Access typically requires removing the control-bezel or panel; handle clips and small fasteners carefully.
• Align the lever onto the switch plunger and secure the bezel; do not force plastic parts to avoid breakage.

This lever-style button is the user-facing push control that engages a mechanism when pressed, restoring proper control input and tactile feedback. It's a direct-replacement component used where a worn or broken button prevents normal operation. What it does:

• Provides a firm, responsive surface for pressing controls or releasing a latch
• Restores proper mechanical engagement when original button is cracked, loose, or missing
• Helps eliminate intermittent or non-responsive button presses caused by damaged button parts
• Matches OEM fit and function to maintain original user interface feel

• One lever-style push button

• High-level replacement; most installations require removing the control panel or trim to access the button
• Power off and unplug the appliance before beginning work to avoid shock or injury
• Handle small plastic parts carefully to avoid damage; test button function before reassembling all panels

This replacement home bar case is the inner door shelf that holds bottles and small items in the refrigerator door, restoring storage function and a finished interior look. It fits the refrigerator's dedicated home/bar compartment. What it does:

• Provides a secure shelf for bottles, cans, and small containers in the door's home/bar area
• Restores proper spacing and support so items sit level and stay in place
• Replaces cracked, broken, or missing door-shelf housings that cause items to fall or rattle
• Helps maintain the refrigerator's intended interior organization and appearance

• One home bar case (single inner door shelf housing)

• Remove food and items from the door before replacing; handle glass or plastic shelves carefully
• Usually installs with snap-in tabs or a small number of screws—do not force parts; align tabs before pressing
• If your door has wiring or lighting nearby, disconnect power to the refrigerator before working on the door

This ice maker drive gear replaces the small plastic gear that turns the ice tray and advances the ice maker. Restores reliable rotation so the ice maker can harvest and eject ice properly. What it does

• Drives the ice tray/arm assembly so the ice maker can cycle and eject ice.
• Replaces worn or broken gear teeth that cause slipping or grinding.
• Helps stop intermittent or complete failure of the ice maker to produce ice.
• Useful when the ice tray spins slowly, stalls, or makes unusual noises.

• Disconnect power to the appliance before beginning any repair.
• Inspect surrounding gears and the motor shaft for damage; replace additional parts if worn.
• Handle small plastic parts carefully to avoid damaging gear teeth during installation.
• Follow the refrigerator service manual for proper removal and reassembly procedures.