Lrbm20512ww Parts

This display cover protects the appliance's control board and display while keeping the control area visible and clean. It restores the finished look of the control panel and shields buttons and the display from spills and wear. What it does:

• Protects the electronic display and control buttons from moisture, dust, and everyday wear
• Keeps the control area visible and easy to read
• Helps prevent accidental contact with control board components
• Restores a worn, cracked, or discolored control panel for improved appearance

• Disconnect power to the appliance before removing or installing the cover to avoid shock or damage
• Remove any retainers or control panel screws as needed; handle the cover carefully to avoid scratching
• Align the cover to the control panel and secure all fasteners; test controls after reassembly
• Replace those components before installing the cover

This Magic Room cover is the replacement shelf cover for the refrigerator's convertible compartment, restoring a flat, stable surface to hold food and containers. It helps keep items supported and the compartment functioning as intended. What it does:

• Replaces a cracked, chipped or missing Magic Room shelf cover
• Provides a stable surface for storing foods and containers in the convertible compartment
• Helps maintain proper spacing and support for drawer/bin components
• Prevents items from falling through or contacting temperature controls below

• Remove food and any drawers or bins that block access before installing
• Handle carefully to avoid chipping; support edges when sliding into place
• Reassemble components in reverse order and ensure the cover seats securely
• Follow all safety steps in the refrigerator owner's manual; unplug or power off if recommended for your model

This door stopper cushions and limits an appliance door's travel to prevent slamming and reduce wear on the hinge. It helps the door close smoothly and reduces noise for a better user experience. What it does

• Stops and cushions the door at the end of its swing to prevent hard impacts
• Reduces hinge and cabinet wear caused by repeated slamming
• Helps eliminate banging or rattling noises during door movement
• Can restore proper door feel when the original stopper is cracked, worn, or missing

• One door stopper

• Service with the appliance unplugged and/or power disconnected for safety
• Typically installed at the hinge/cabinet area using basic hand tools; may require removing a trim or access panel
• Inspect hinge screws and mounting area; replace any damaged hardware and tighten to secure the stopper

This mechanical mounting band secures a bracket assembly inside the appliance to keep components aligned and reduce vibration. It restores proper bracket positioning so moving parts run quietly and reliably. What it does:

• Holds a bracket or component assembly in place to maintain proper alignment
• Dampens movement and reduces vibration-related noise or rattling
• Prevents excess wear by keeping parts from shifting during operation
• Helps maintain correct clearances to avoid interference or rubbing

• Disconnect power before inspecting or replacing internal parts
• Remove only the fasteners necessary to access the bracket; keep track of hardware
• Secure all fasteners to the manufacturer's torque or snug specification
• Replace the band if bent, cracked, or missing to restore proper fit and function

This injection tube directs water to the refrigerator ice maker so the mold fills correctly and produces ice. It replaces a cracked or blocked tube to restore reliable water flow to the ice-making assembly. What it does:

• Channels water from the valve to the ice maker fill cup for proper ice production
• Helps prevent leaks caused by cracked or brittle tubing
• Commonly replaced when the ice maker won't fill, fills slowly, or leaks near the ice mold
• Works with the ice maker fill system; not a water valve or pump

• Disconnect power and shut off the water supply before starting work
• Inspect adjoining fittings and seals; replace worn grommets or clips as needed
• Handle carefully to avoid kinks or damage to the tube during installation

Replacement shelf glass for refrigerator interiors that provides a stable flat surface for food storage and helps contain spills. Restores a cracked or missing shelf so you can safely organize items and use full storage capacity. What it does:

• Provides a sturdy, level platform for food, containers and small appliances.
• Helps contain spills and makes cleanup faster and easier.
• Replaces cracked, chipped or missing shelves that cause unstable storage or lost usable space.
• Restores proper shelving so items sit flat and doors/drawers close without obstruction.

• Handle carefully; wear cut-resistant gloves when installing or removing damaged glass.
• Slide the shelf into the refrigerator's existing supports or clips—do not force or flex the glass.
• Confirm shelf is fully seated and level before loading; do not overload beyond the refrigerator's recommended shelf capacity.
• If support brackets or clips are broken, replace them before using the new shelf.

A replacement refrigerator door gasket that restores the door seal to help maintain proper cooling and energy efficiency. Replaces torn, cracked, or hardened gaskets to reduce warm air leaks and moisture buildup. What it does:

• Seals the refrigerator door to keep cold air inside and warm air out
• Helps reduce frost buildup and prevents moisture from entering the compartment
• Supports consistent internal temperature for better food preservation
• Stops drafts and improves compressor efficiency when sealing properly

• Disconnect power to the appliance before starting any repair
• Remove the old gasket by loosening door trim or fasteners as needed; clean the sealing surface before installing the new gasket
• Press the new gasket into the channel evenly and ensure the magnetic/locking edge seats fully around the door
• After installation, close the door and check for gaps; allow the gasket to form to the door over normal use

This guide tube is a small routing sleeve that supports and protects a rod, shaft, cable, or line inside your appliance. It keeps the path straight to reduce friction, noise, and premature wear.

• Guides and supports a rod/shaft/cable/tube through the chassis
• Maintains alignment for smooth movement or flow
• Helps prevent chafing, kinks, and vibration-related damage
• Typical failure signs: scraping or rattling noises, binding/misalignment, or visible cracks/deformation

• Disconnect power; turn off water or gas before servicing
• Refer to your model's parts diagram for routing and mounting points
• Reuse original screws/clips unless damaged
• Route exactly like the original; avoid pinches/kinks and verify clearances before restoring power

This tray assembly is the molded replacement tray that supports and contains items inside the appliance drawer, restoring stable storage and helping the drawer operate and close as intended. What it does

• Provides a stable base for items stored in the drawer.
• Replaces cracked, warped or otherwise damaged trays that allow items to shift or leak.
• Restores proper fit and alignment so the drawer slides and closes more reliably.
• Helps keep contents contained and reduces spills inside the drawer area.

• Remove contents from the drawer and slide the drawer out before replacing the tray.
• Installation is typically straightforward; clips or rails may need to be released—refer to your model's service manual for the exact procedure.
• Use basic hand tools only if required; avoid forcing parts or damaged mounting clips.
• Keep parts and small fasteners away from children; dispose of damaged pieces safely.

This drawer tray assembly replaces a worn, cracked, or missing refrigerator drawer tray to restore proper storage and containment in the drawer. It provides a stable, easy-to-clean surface for stored food and helps keep the drawer functioning smoothly. What it does:

• Replaces the plastic tray that forms the bottom of a refrigerator drawer or drawer bin.
• Restores proper containment for foods and prevents items from falling through or collecting in damaged areas.
• Helps the drawer slide and seat correctly when the original tray is broken or warped.
• Common symptoms: visible cracks or breaks, sagging or uneven drawer bottom, food or liquids pooling inside the drawer.

• One drawer tray assembly

• Disconnect power and remove food from the affected drawer before beginning service.
• Remove the drawer per your model's instructions, then lift out the old tray and snap or slide the new tray into place.
• Handle plastic parts carefully to avoid cracking during installation; use basic hand tools only if required.

This overload protector is a direct-replacement electrical safety device that helps protect the compressor motor from overheating and overcurrent. It trips the circuit when the compressor draws excessive current, helping prevent damage and allowing normal operation once cooled. What it does:

• Detects excessive current or high temperature at the compressor and interrupts power to prevent motor damage.
• Helps stop hard-starting or repeated short-run cycles caused by motor overload.
• Commonly linked to symptoms such as a refrigerator or freezer that hums or clicks, runs briefly then stops, or fails to maintain proper cooling.
• Works with the start components to ensure reliable compressor startup and protect against electrical stress.

• Always unplug the appliance or disconnect power at the breaker before servicing.
• Handle compressor terminals and wiring carefully; avoid bending or damaging terminal tabs.
• Replace with the identical part number or OEM-specified protector to ensure correct fit and electrical ratings.
• After installation, restore power and observe the appliance through one full start/stop cycle to confirm normal operation.

This lower cover is the front access panel that protects the appliance's internal components and gives the cabinet a finished look. It restores the lower front appearance and shields wiring and assemblies from dust and debris. What it does

• Replaces a cracked, dented, or missing lower front panel to restore protection and appearance
• Covers and protects wiring, hoses, and base components from dust and accidental contact
• Helps reduce drafts and keeps the cabinet interior cleaner
• Common symptom: visible damage, loose panel, or exposed lower components

• Remove power and disconnect the appliance before beginning any work.
• Usually secured with a few screws or clips at the front base; support the panel while removing fasteners to prevent drops.
• Use basic hand tools; avoid forcing clips to prevent cabinet damage.
• If wiring or components are exposed or damaged, inspect and address those issues before reassembly.

The Defrost Sensor is an OEM part for LG refrigerators. It detects when the evaporator coils require defrosting, allowing the defrost system to initiate and remove any built-up frost or ice. This sensor is typically located near the evaporator coils, monitoring their temperature and signaling when defrosting is necessary.

Causes of a faulty defrost sensor can range from physical damage or exposure to moisture, to electrical connectivity issues or general wear over an extended period.

Symptoms of a bad defrost sensor include:

• Excessive frost or ice buildup on the evaporator coils
• Inadequate cooling or improper temperature regulation
• The defrost cycle not initiating when required

This OEM LG part is also compatible with some Kenmore models.