Lre3193bm Parts

This single wire harness connects controls and components to deliver power and signals so affected functions run correctly. It replaces a damaged harness to restore reliable electrical connections and consistent operation. What it does:

• Transfers power and control signals between the control board and individual components
• Restores missing or intermittent power to components when a harness is damaged
• Prevents shorts and poor connections caused by frayed wires or broken terminals
• Typical symptom: appliance or specific functions do not power up, run intermittently, or behave erratically

• Disconnect power to the appliance before starting any work.
• Match connector shapes and wire colors; seat each connector fully until it clicks.
• Route the harness following existing clips and retainers to avoid chafing or pinching.
• If terminals are corroded or connectors are damaged, replace the harness rather than attempting repairs.

This factory-specified fastener secures designated panels and components, restoring a precise fit and helping keep your appliance solid and quiet. Replace a missing, stripped, or rusted original with the correct OEM match for the specified locations.

• Secures brackets, panels, and internal parts where this part number is called out
• Replaces damaged, stripped, corroded, or lost screws
• Helps reduce looseness and vibration that can cause rattling noises
• Exact OEM replacement for positions requiring this specific screw

• Disconnect power and shut off water/gas before servicing
• Match to the removed screw and install only in the locations specified for this part number
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening, especially into plastic
• If multiple screws are involved, start all fasteners before final tightening to ensure alignment

This single wiring harness connects electrical components to restore reliable power and signal routing within the appliance. It replaces damaged or burnt harnesses to help return normal operation and prevent intermittent faults. What it does

• Routes power and signal between control boards, sensors, and motors for proper operation
• Replaces frayed or melted wiring that can cause intermittent function or component failures
• Helps resolve symptoms like no power to a component, intermittent operation, or error codes related to open circuits
• Restores factory wiring organization and secure connector fit for reliable connections

• One wiring harness assembly

• Disconnect power before servicing to avoid shock or damage
• Verify connector orientation and fully seat all plugs; do not force connectors
• Replace only with the exact harness to maintain correct wire lengths and connector types

This is a replacement customized screw designed to secure appliance panels and components. It restores proper fit and fastening where the original screw is lost or worn, helping maintain safe, stable operation. What it does

• Replaces missing or damaged mounting screw used on appliance panels and internal components
• Restores secure fastening to reduce vibration and rattling during operation
• Matches the original OEM fit and thread form for correct engagement when verified for your model
• Helps prevent loose parts that can cause noise or interfere with moving components

• Disconnect power and water before servicing the appliance
• Verify screw size, thread direction, and length match the original before installation
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten securely but avoid overtightening to prevent stripping or damaging mating threads

This door handle mounting anchor creates the fixed attachment point on the appliance door or drawer. Replacing a worn or missing anchor restores a solid, wobble-free handle and a consistent feel when opening and closing.

• Provides the secure mounting point that the handle fastens to
• Helps keep the handle aligned and rigid during use
• Replace if the anchor is cracked, stripped, or missing
• Resolve a loose/wobbly handle, a handle that won't tighten, or misalignment after service

• Disconnect power; turn off the water supply
• Protect the door/drawer finish and support the handle during removal
• Remove the handle per your model's instructions and take out the damaged anchor
• Install the new anchor using the existing mounting location/hardware, seat the handle fully, then tighten set screws evenly without overtightening

This slider is a replacement glide piece that helps a drawer or sliding compartment move smoothly and stay aligned. Replacing a worn slider restores quiet, consistent travel and prevents wear on the surrounding trim. What it does:

• Guides and supports a drawer or sliding compartment for even movement
• Reduces sticking, scraping, and noisy operation from worn glides
• Keeps the drawer aligned to prevent rubbing or binding against the cabinet
• Helps extend life of associated rails and trim by restoring proper tracking

• One slider glide piece

• Disconnect power to the appliance and remove any contents before servicing
• Remove the drawer or access panel per your appliance instructions to reach the slider
• Inspect mating rail and fasteners; replace any damaged clips or screws for a secure fit

This mounting bracket secures internal components or panels to restore proper alignment and support. Replacing a damaged bracket helps stop rattling, sagging, or loose panels for safer, more reliable appliance operation. What it does:

• Provides structural support for panels, trim, or internal components.
• Prevents movement that can cause rattling or noise during operation.
• Restores proper alignment when a worn or broken bracket lets parts sag or shift.
• Helps maintain secure fitment after repair or component replacement.

• One mounting bracket as shown.

• Disconnect power to the appliance before starting any repair.
• Basic hand tools (screwdriver, nut driver) are typically required; for exact fasteners.
• Remove surrounding trim or panels carefully to access the bracket; keep hardware for reassembly.
• If multiple brackets show wear, inspect and replace as needed to ensure even support.

This supporter is a small mounting support used to stabilize and secure nearby components within the appliance, helping reduce vibration and maintain proper alignment for reliable operation. What it does:

• Provides structural support for an internal assembly or panel
• Helps keep linked components aligned and reduces rattling or vibration
• Restores proper fit where a worn or broken support causes looseness
• Supports normal operation by holding parts in their intended position

• One supporter mounting support

• Intended for replacement of a single damaged or missing support; verify part location before ordering
• Turn off and unplug the appliance (or shut off power) before servicing
• Use appropriate hand tools; avoid over-tightening fasteners to prevent cracking

The Broil Element is an OEM replacement part for LG electric ranges. As a vital upper heating system, this broil element helps efficiently brown and crisp foods placed directly under or on the top rack of the oven.

Causes of a defective broil element may relate to normal wear and tear on the coils from repeated high-heat cooking. Food residues adhering over time can reduce performance.

Symptoms of a problematic broil element include:

• Inadequate or uneven browning from the top-level heating system   
• Diminished functionality of the broil setting on the control panel
• Potential thermal damage or exposed wiring from a failed element

This OEM component fits some Kenmore/Sears electric range models as well. 

The Main Control Board is an OEM part for LG electric ranges. As the central processing component, it operates all cooktop and oven functions including heating element control, temperature regulation, timers, and safety features.

Symptoms of a faulty main control board involve:

• Heating coils or burners failing to switch on or reaching proper heat levels  
• Oven temperature displays flickering or failing to read accurately
• Timers malfunctioning or failing to countdown correctly
• Recurring error codes disabling use of oven or cooktop functions

Causes can be moisture damage seeping circuitry over time. Electrical anomalies from power fluctuations are also possible causes of failure. 

This LG replacement is compatible with select Kenmore models as well.

This heater assembly replaces the dryer's heating unit to restore warm air for effective drying. It fits into the dryer's blower/air path and provides the heat source needed to evaporate moisture from clothing. What it does:

• Houses the heating element and directs warm air through the drum
• Restores normal drying temperatures when the original heater fails
• Common symptom: dryer runs but clothes remain damp or take much longer to dry
• Common symptom: reduced or no warm air coming from the dryer

• Disconnect power (and gas supply for gas models) before beginning any repair
• Handle heating elements and terminals carefully to avoid damage
• After installation, test dryer operation and check for proper airflow and secure electrical connections

This is a replacement front control panel that houses and protects the microwave's touch controls and display, restoring usable controls and a finished appearance. It fits behind the exterior trim and connects to the control board. What it does:

• Provides the front surface for touch pads, buttons and display elements
• Protects electronic controls from spills, grease and wear
• Restores readable display and button functionality when the panel is damaged or cracked
• Helps eliminate intermittent or unresponsive key presses caused by a broken or warped panel

• Disconnect power (unplug or trip breaker) before starting any repair
• Handle the panel carefully to avoid scratching or cracking; soft gloves recommended
• May require removal of trim, door assembly or control board access to install

This customized washer is a small hardware piece that secures fasteners and helps distribute load where screws or bolts attach to appliance components. It restores proper fit and reduces movement at the connection point. What it does:

• Provides a stable bearing surface for screws or bolts to prevent pull-through and material damage
• Helps keep fasteners tight and reduces vibration-related loosening or rattling
• Maintains correct spacing and alignment of panels or internal parts
• Can help form a seal on fasteners in locations prone to vibration or minor movement

• Disconnect power and water (if applicable) before servicing the appliance
• Retain or replace the associated fastener; small parts can be easily lost—work on a clean surface