Lrg5115st Parts

This insulator is the mica sheet that covers the microwave's waveguide opening. It shields the cavity from food splatter and moisture while allowing microwave energy to pass, helping prevent arcing and protecting internal components.

• Covers the waveguide port to keep grease and debris out
• Helps prevent sparking/arcing inside the cavity
• Restores safe, even microwave operation when the original is burned or stained
• Typical symptoms: visible burn marks or charring on the cover, arcing/sparking during use, unusual noises

• Unplug the appliance before service; high-voltage components can retain charge
• Remove the old cover by releasing mounting screw or tabs; clean residue from the area
• Do not bend or crack the new mica; install with the same orientation
• If trimming is required per service literature, follow the outline of the original cover only

This hardware washer helps distribute fastener load and maintain proper spacing in your LG appliance. Replacing a missing or worn washer restores secure mounting and alignment, reducing vibration and rattling from loose assemblies.

• Distributes the load of a screw or bolt and protects mating surfaces to maintain alignment
• Helps keep components secure and at the correct spacing
• A damaged or missing washer can lead to loosening, vibration, or rattling during operation
• Ensures correct hardware stack-up during reassembly after service

• Disconnect power and shut off water or gas before servicing
• Note the order and orientation of any washers/spacers; take a reference photo
• Use the correct driver or wrench and tighten snugly—do not overtighten
• Replace companion hardware if corroded, stripped, or damaged

This gas valve assembly controls the flow of natural or LP gas to the oven/range burner, restoring safe ignition and burner operation. Replace a faulty valve to help resolve burners or oven not lighting or heating inconsistently. What it does:

• Regulates gas flow to the oven/burner burners so they ignite and maintain a steady flame
• Works with the oven/range ignition system and safety controls to open and close gas supply
• Commonly replaced when burners fail to light, flame is weak or intermittent, or oven won't heat
• Designed as a direct replacement assembly for the original valve configuration

• One gas valve assembly as shown

• Shut off both gas supply and electrical power before beginning any service
• After installation, check all fittings for leaks with a gas leak detector or soapy water and test operation
• Do not alter the valve or regulator; follow appliance manufacturer instructions

The Gas Orifice Nozzle is an OEM part for LG gas ranges. The gas orifice nozzle regulates the amount of gas entering the burner assembly. It meters out the proper gas flow needed for combustion.

Causes of a bad gas orifice nozzle include mineral buildup obstructing the small opening over time or impact damage distorting the nozzle. 

Symptoms of a faulty nozzle are:

• Unstable or irregular burner flames  
• Changes in flame coloration
• Smells of gas from the range top 
• Inconsistent or improper heating

This part is also compatible with select Sears/Kenmore ranges.

This packing gasket seals the refrigerator door to help maintain proper temperature and energy efficiency by keeping cold air in and warm, moist air out. It replaces a worn, torn or misshapen door seal to restore a tight closure. What it does:

• Forms an airtight seal around the door edge to reduce cold air loss and prevent warm air intrusion
• Helps stop frost buildup and excess moisture inside the compartment
• Reduces compressor run time caused by air leaks
• Restores proper door alignment and improves cooling performance when old gasket is deformed

• One door packing gasket

• Unplug the appliance or shut off power before starting work
• Clean the door flange thoroughly and remove any old gasket adhesive or debris before installing
• Start at one end and press the gasket evenly into the channel; ensure full seating around the entire perimeter
• If needed, slightly warm the gasket with low heat (hair dryer) to make it more pliable—avoid overheating or stretching

The Burner Assembly is an OEM component specifically designed for LG gas ranges equipped with sealed cooktop burners. This integral assembly contains the ignition electrode, valve stem, and cast burner head to conduct flame across grates.  

Symptoms of a bad burner assembly include:

• Inability to ignite or maintain consistent flames under cookware
• Yellow broken or excessive flame instead of steady blue  
• Clicking ignition sounds but no combustion takes place
• Deteriorated valve stems limiting gas flow regulation

Causes of failure involve clogged ports blocking gas dispersion, cracked burner bases no longer supplying sufficient air intake, or damaged ignition systems disabling piezo sparks over dozens of heating cycles.

Replace yours today with this genuine OEM LG assembly to restore optimal cooktop performance. Factory-sealed construction withstands daily use maintaining even heat across pans and preventing gas leaks. Compatible with GE, Frigidaire, and Kenmore sealed burner models as a direct unit replacement.

A small structural support bracket that holds or stabilizes internal components. Replaces a worn or broken supporter to restore proper alignment and reduce movement that can cause noise or poor operation. What it does:

• Provides mounting support for internal panels or components to keep parts aligned
• Prevents sagging or shifting that can cause rubbing, vibration, or intermittent contact
• Restores proper component spacing after a cracked or missing bracket
• Commonly replaced when the original supporter is cracked, broken, or missing

• Disconnect power (and water supply, if applicable) before beginning any repair
• Basic hand tools may be needed; handle plastic brackets carefully to avoid breakage
• Inspect surrounding clips or fasteners and replace if damaged to ensure a secure fit

This supporter mounting bracket secures internal components or trim so they stay properly aligned and stable. It helps stop sagging, movement, and vibration that can affect operation or cause noise. What it does

• Holds and stabilizes a panel, shelf, or assembly to prevent shifting during use
• Reduces rattling, banging, or vibration caused by a loose component
• Keeps parts aligned for smooth opening and closing of drawers or doors
• Restores proper fit where a worn or broken support was causing misalignment

• Disconnect power (and water, if applicable) before servicing to avoid shock or flooding
• Inspect mounting points and screws; replace any damaged hardware for a secure fit
• Hand-start fasteners, then tighten snugly—do not overtighten plastic anchors