Lrmds3006s Parts

This center hinge assembly replaces the middle hinge that supports and aligns refrigerator doors so they open and close smoothly. It restores proper door height and helps maintain an even seal for efficient cooling. What it does:

• Supports the refrigerator door at the center pivot point to prevent sagging and misalignment
• Keeps doors properly aligned so gaskets meet evenly and the door seals correctly
• Reduces noise or binding when opening and closing a door
• Restores stable door movement after a worn or damaged hinge

• One center hinge assembly

• Disconnect power and empty doors or support contents before removing the door
• Removing and reinstalling doors may require two people to prevent damage or injury
• Use existing mounting hardware if in good condition; replace any stripped or damaged fasteners

This Vegetable Tray Assembly is the replacement crisper pan that stores fruits and vegetables in your refrigerator, helping keep produce organized and contained. Durable plastic construction fits into the refrigerator crisper area. What it does:

• Replaces a cracked, warped or missing crisper pan so produce stays contained and upright
• Provides a flat, washable surface for fruits and vegetables
• Helps prevent spills from leaking into lower cabinet areas
• Restores proper fit and clearance for the crisper drawer above/below

• One vegetable tray assembly

• Remove produce and the crisper drawer before replacing the tray
• Slide old tray out and position new tray on the guides until it seats securely
• Handle edges carefully and clean tray before first use

This thermistor assembly senses temperature and provides a reliable temperature signal for the appliance control system, helping the unit maintain proper operating temperatures and cycle components as needed. What it does

• Monitors temperature at the sensor location so the control board can regulate cooling/defrost cycles.
• Helps prevent prolonged compressor or heater runs by signalling when temperatures reach set points.
• Commonly linked to symptoms like inconsistent temperatures, long run times, or failure to reach target cooling.
• Works as a direct replacement sensor assembly for systems that specify a PTC thermistor assembly.

• One thermistor assembly as shown.

• Disconnect power to the appliance before servicing to avoid shock or injury.
• Handle the sensor and wiring gently; avoid bending or damaging the sensing element.
• Verify connector orientation and secure all wiring; loose connections can cause intermittent operation.

This lamp cover is the replacement light lens that protects and diffuses the appliance's internal lamp, restoring even illumination and shielding the bulb from moisture and debris. It's a direct-fit exterior lens for the lamp assembly. What it does:

• Protects the interior lamp from dust, moisture and impact to help prevent bulb damage
• Diffuses and directs light for even illumination inside the compartment
• Restores a cracked, yellowed or missing lens to improve visibility
• Helps maintain the lamp assembly's proper fit and alignment

• One lamp cover / light lens

• Power off and unplug the appliance before beginning any service
• Remove lamp bulb per manufacturer instructions before replacing the cover to avoid damage
• Use proper tools and handle the lens gently to avoid scratching or cracking
• If mounting clips or screws are worn or missing, replace them separately

Right side rail.

This door stopper cushions and limits a refrigerator or appliance door's movement to reduce slamming and protect the cabinet and hinge. It restores smooth, quiet door closing and helps keep the door aligned. What it does

• Absorbs impact when the door is opened or closed to prevent slamming and wear.
• Limits door travel to protect hinges and adjacent cabinet surfaces.
• Helps maintain proper door alignment for a better seal and quieter operation.
• Commonly replaced when the stopper is worn, cracked, or missing.

• One door stopper

• Disconnect power to the appliance or follow manufacturer safety guidance before servicing.
• Typically attaches at the door or frame with a screw or snap fit; remove trim or access panels if needed.
• Inspect surrounding mounting area and replace any worn fasteners or brackets.

This supporter cover is a replacement internal bracket that helps secure the TV's back or front cover, restoring proper panel alignment and reducing movement. Fits where the cover needs a mounting or support point to sit flush and stable. What it does

• Provides structural support to the TV cover or bezel so panels align correctly.
• Prevents cover flexing or sagging that can cause gaps or rubbing.
• Helps stop rattling or vibration-related noise caused by loose cover panels.
• Restores proper mounting points for screws or clips that hold the cover in place.

• One supporter cover.

• Unplug the TV and place it on a soft, flat surface before beginning.
• Remove the external cover or bezel per the service manual to access the mounting location.
• Keep track of screws/clips; use the same hardware unless replacement is specified.