Lsc27921sw/00 Parts

A replacement door stopper assembly that cushions and limits door travel to prevent slamming and reduce wear. Installs at the door hinge area to restore smooth, quieter closing and proper alignment. What it does:

• Cushions and limits door travel to prevent hard impacts and reduce noise.
• Keeps the door from over-traveling to protect hinge components and frame.
• Replaces a worn or broken stopper that can cause the door to slam, bind, or close unevenly.
• Helps restore consistent door feel and alignment after damage or wear.

• Disconnect power (and gas if applicable) before starting any repair.
• Support the door or have a helper when removing hinge hardware and the old stopper.
• Retain all screws and small parts during disassembly; use appropriate hand tools.
• After installation, cycle the door several times and verify smooth operation and alignment.

This motor support damper sits between the refrigerator's compressor and base to absorb vibration and movement. Replacing a worn damper helps quiet rattles and humming from the back of the cabinet and keeps the compressor properly supported.

• Cushions the compressor to reduce transmitted vibration and noise
• Helps quiet humming, buzzing, or rattling from the lower rear of the refrigerator
• Maintains proper compressor alignment and support on the base pan
• Common signs of wear: increased vibration/noise, a cracked or flattened damper, or noticeable compressor movement when running

• Unplug the refrigerator and pull it forward to access the rear; allow the compressor to cool before working
• Support the compressor to remove load from the mount before loosening hardware
• Replace the damper and tighten mounting hardware evenly without over-compressing the rubber
• Avoid bending or stressing refrigerant tubing; wear gloves and eye protection

This name plate is the exterior emblem that mounts to the appliance's front panel. It replaces a missing, cracked, or faded badge to restore a clean, factory look and cover the designated trim area.

• Attaches to the outer panel to display brand/series identification
• Restores a finished appearance where the original emblem sits
• Direct replacement for a lost, damaged, or worn badge
• Typical symptoms: missing emblem, loose or broken tabs, peeling, or discoloration

• Disconnect power before servicing the appliance
• Carefully remove the old emblem; release any tabs from behind or peel away remaining adhesive
• Clean and dry the mounting surface; remove all residue for best fit
• Align with the recess/holes and press evenly until fully seated

Replacement plastic door basket that mounts to the inside refrigerator door to keep bottles, condiments and small items organized and secure. Restores usable door storage and helps prevent items from shifting or falling. What it does

• Holds bottles, jars, condiments and other door-stored items to maximize door storage space.
• Replaces a cracked, broken or missing door bin that no longer secures items.
• Common symptom: items slide, fall out, or the bin is loose or won't stay in place when the door is opened.
• Snaps into the refrigerator door rail to form a stable storage shelf.

• Remove all items from the door before replacing the basket.
• Align the basket with the door rails and press until it snaps into place; reverse to remove.
• Handle with care to avoid cracking the plastic; replace if mounting clips are damaged.

This auger motor rotates a refrigerator's ice dispenser auger, which in turn moves ice cubes out through the dispenser chute. If the motor is faulty or broken, the user may notice ice does not dispense or may hear a loud, grinding sound from the appliance despite no ice being produced. In such cases, the motor will need to be replaced. Wear work gloves and be sure to unplug the appliance from the outlet and store perishable foods safely before starting any repair work.This is a replacement auger motor that has been manufactured by LG and sourced directly from the manufacturer. This genuine OEM part is compatible with different refrigerators. This part is sold individually and is a genuine part made of high-quality, durable, non-corrosive materials.

A replacement refrigerator door gasket that restores a tight seal to help maintain proper temperature and efficiency. Replaces a worn or torn seal to reduce air leaks and help prevent frost and moisture build-up. What it does:

• Seals the door to keep cold air in and warm air out, helping the appliance maintain set temperatures
• Helps reduce frost, condensation, and moisture on the inner liner
• Can improve cooling performance and reduce excessive run time caused by leaks
• Addresses symptoms like visible gaps, tears, warped edges, or persistent condensation at the door

• One refrigerator door gasket

• Disconnect power to the appliance before replacing the gasket to avoid electrical risk
• Remove the old gasket carefully and seat the new gasket fully into the door channel; some trim or fasteners may need to be loosened
• Check door alignment and closing after install; ensure the gasket compresses evenly around the door perimeter
• Wear gloves to protect hands and avoid damaging the new gasket while handling

This is a genuine replacement screw used to secure appliance panels and components. It restores proper fastening so panels and assemblies stay aligned and operate safely. What it does:

• Fastens panels, brackets, and small assemblies to maintain structural integrity
• Replaces missing or stripped screws that cause rattling or loose parts
• Helps stop vibration-related noise when used in its original mounting locations
• Matches the OEM fit to ensure proper alignment and clearance

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread or component damage
• Disconnect power to the appliance before working on electrical components
• Replace all matching fasteners for even fit

This holder is a small mounting bracket used to secure internal components in place, helping keep parts aligned and stable for reliable operation. It provides a direct, OEM-compatible replacement to restore proper fit and function. What it does

• Secures and supports nearby components to prevent shifting or vibration.
• Restores proper alignment where a worn or broken holder causes rattling or loose parts.
• Helps maintain normal operation by keeping assemblies seated correctly.
• Works behind panels or inside assemblies where a dedicated bracket is required.

• One holder/mounting bracket as shown.

• Installation generally requires removing the panel or access cover where the holder is located.
• Use proper fasteners shown in your appliance; replace any damaged screws or clips as needed.
• Disconnect power before servicing electrical appliances to reduce shock risk.

This pipe holder is a small plastic clip that secures tubing and small pipes inside the appliance, helping keep lines organized and preventing rubbing or disconnection. It restores proper routing and reduces vibration-related noises. What it does:

• Holds and secures water, drain, or refrigerant tubing to prevent sagging and chafing
• Keeps lines routed away from moving parts to reduce wear and noise
• Helps maintain proper tube alignment to avoid strain on fittings
• Commonly replaced when the original clip is cracked, broken, or missing

• Disconnect power and water before working on the appliance
• Inspect surrounding tubing and fittings for damage when replacing the clip
• Typically installs as a push-fit or snap-on clip; use gentle pressure and avoid forcing
• Replace broken or brittle clips to prevent tubing damage or leaks

The Drain Tube Assembly is an OEM part for LG refrigerators. This drain tube assembly is responsible for directing condensation and melt water that accumulates in the refrigerator away to the evaporator pan.

Causes can include cracks developing from limescale or mineral accumulation, flexing fatigue from repeatedly catching drips, or damage from improper cleaning methods.

Symptoms of a bad drain tube assembly include:

• Puddles or leaks developing underneath the refrigerator
• Poor air flow from vents and higher temperatures
• Ice or moisture buildup in refrigerator walls and seals
• Water stains or corrosion appearing inside the unit

This OEM LG part is also compatible with some Kenmore models.

This bracket motor secures and supports the appliance motor assembly, restoring proper alignment and stable operation. Replacing a worn or broken bracket helps reduce noise and prevents motor misalignment that can cause poor performance. What it does:

• Holds the motor assembly in the correct position so the motor runs smoothly and stays aligned.
• Prevents excess vibration and rattling caused by a damaged or cracked bracket.
• Helps stop intermittent motor movement or binding that can affect operation.
• Reduces risk of additional wear to the motor or connected components due to misalignment.

• One bracket motor

• Disconnect power to the appliance before beginning any work.
• Replacement typically requires removing access panels and supporting the motor during removal/installation.
• Inspect surrounding fasteners and mounting surfaces; replace any damaged hardware.