Lsfxc2476s Parts

This slide rail supports and guides a refrigerator drawer so it opens and closes smoothly. Replacing a worn or cracked rail restores proper alignment and glide to prevent bins from binding, tilting, or popping out of the track.

• Provides the track the drawer/bin slides on
• Maintains drawer alignment and supports the bin during use
• Helps ensure smooth, even travel in and out
• Common failure signs: drawer hard to open/close, crooked or sagging bin, drawer comes off track, visible cracks or damage to the rail

• Disconnect power and remove the affected drawer/bin before starting.
• Remove screws securing the old rail; install the new rail in the same position and orientation.
• Transfer any reusable stops/caps from the original rail if applicable.
• Reinstall the drawer and verify smooth operation before reloading.

This fan grille assembly covers the internal fan and channels airflow through the air ducting, protecting the fan while helping your appliance circulate air efficiently for even, reliable temperatures and quieter operation. What it does:

• Shields the fan and directs airflow through the cabinet
• Helps maintain proper circulation for consistent cooling performance
• Replaces cracked, warped, or missing grille panels that disrupt airflow
• Common symptoms: rattling or scraping near the fan area, broken louvers, weak airflow, temperature fluctuations, or frost/ice buildup around the cover

• One fan grille assembly

• Disconnect power to the appliance before servicing
• Remove shelves/drawers or trim as needed to access the grille
• Remove mounting screws/clips and gently release plastic tabs; disconnect any attached wiring harnesses and note routing
• Transfer any reusable insulation or foam seals from the original part if present; ensure the fan spins freely before reassembly and restoring power

This is an air duct and evaporator cover with fan that is used in refrigerators. This part makes up the back wall of the refrigerator and is used to channel cold air into the refrigerator. It also protects the evaporator. It includes the fan, which circulates cold air throughout the appliance. If any of these parts are damaged, the refrigerator may get too hot or make squealing noises.Before replacing the air duct and evaporator cover with fan, make sure that any food that could go bad while the refrigerator is unplugged has been placed in a cooler or other cold location. Disconnect the refrigerator from power once food has been safely stored. While making the replacement, make sure to wear a pair of work gloves for safety.The air duct and evaporator cover with fan is made to be compatible with a series of refrigerators by LG. It is sold individually and sourced straight from the manufacturer. The component is an authentic OEM replacement part.

This filter assembly head is the replacement water filter housing that secures the cartridge, routes incoming water, and seals the connection to the dispenser/ice system. It restores a proper filter mount and helps prevent leaks or loss of water flow. What it does:

• Holds and seals the water filter cartridge to the refrigerator's water line
• Routes filtered water to the dispenser and ice maker
• Commonly replaces a cracked, leaking, or damaged filter housing
• Can resolve reduced or no water flow when caused by a failed filter head
• Re-establishes a proper seal to prevent drips at the filter connection

• One filter assembly head

• Turn off the refrigerator and shut off the water supply before starting
• Depressurize the water line/dispenser per the refrigerator manufacturer's instructions
• Inspect O-rings/seals and replace if damaged; ensure proper seating when installing the filter
• After installation, turn on water, check for leaks, and run water/dispenser to clear air

The Magnet Switch is an OEM part for LG refrigerators. It plays an important role in monitoring the position of the refrigerator door. 

The magnet switch works together with a magnet installed in the door gasket to detect when the door is opened or closed. It communicates this information to the control board which uses it to manage temperatures and fan speeds accordingly. 

Causes of a bad magnet switch can include wear and tear over time, physical damage, or failure of internal components. 

Symptoms of a bad magnet switch include:

• Improper cooling and freezing performances 
• Inability to detect when the door is opened
• Erratic temperature fluctuations
• Errors codes relating to door sensors

This genuine OEM LG magnet switch restores the door monitoring functions of your refrigerator. It is also compatible with Sears/Kenmore refrigerator models.

This holder is a small mounting bracket that secures a mating component in place inside the appliance. Replacing a cracked or missing holder restores a firm, rattle-free fit and proper alignment.

• Provides a stable mount for the designated part
• Prevents shifting and vibration that can cause noise or premature wear
• Common signs of failure: broken tabs, stress cracks, or the attached part sagging or falling out
• When damaged, the connected component may be loose, noisy, or misaligned

• Disconnect power; if working near water tubing, also shut off the water supply
• Note the original orientation and mounting points; take a photo before removal
• Reuse existing fasteners and avoid overtightening to prevent cracking the plastic
• Ensure the attached component is secure and clears any moving parts before restoring power

This cabinet roller supports the refrigerator and lets the unit roll in and out of place for cleaning or service. Replace a worn or broken roller to restore smooth movement and help keep the appliance properly positioned.

• Supports the base of the refrigerator and enables rolling movement
• Helps with safe positioning and service access without dragging
• Common failure signs: appliance is hard to move, scraping or rolling noises, a flat-spotted/cracked wheel, or a wheel that won't turn
• Replace when the roller is damaged, seized, or missing

• Disconnect power and shut off water supply; protect flooring before moving the appliance
• With help, pull the refrigerator forward and safely support it to access the roller
• Remove mounting fasteners, install the new roller, and reuse original hardware
• Confirm level and smooth movement before returning the unit to its location

This connector joins two sections of the refrigerator's water tubing to create a secure, leak-resistant seal. Replace a cracked or loose connector to restore proper water flow to the dispenser and ice maker.

• Provides a sealed union between two water tubes in the appliance's water system
• Helps prevent air and water leaks that can impact dispenser and ice maker performance
• Typical failure signs include drips or puddles near the connection, visible seepage, or moisture alerts
• Also causes low/no dispenser flow or small or hollow ice cubes

• Disconnect power and shut off the water supply; dispense water to relieve line pressure
• Prepare tubing with a clean, square cut; insert each tube fully into the connector until seated, then pull-test to retention
• Restore water and check all joints for leaks; purge air by dispensing water before normal use

This holder assembly is a structural mounting piece that supports and secures an internal component in your appliance. Replacing a cracked or worn bracket helps restore proper alignment and keeps parts stable during everyday use.

• Provides a rigid mounting point for the attached component
• Keeps parts aligned to reduce movement and vibration
• Helps prevent rattling or noise from loose mounts
• Common signs of failure: visible cracks/broken tabs, looseness, or parts that won't stay seated

• Disconnect power and, if applicable, turn off the water supply before service
• Note the orientation of the original part to match fitment
• Reuse existing mounting screws or hardware unless the manufacturer specifies otherwise
• Do not overtighten fasteners; the secured component is fully seated and stable

This replacement screw secures specified panels or components inside your appliance. Refreshing worn or missing hardware helps restore a tight fit, reduce rattling, and keep assemblies properly aligned for reliable performance.

• Provides secure fastening for brackets, panels, or internal assemblies
• Replaces stripped, rusted, or lost hardware
• Helps reduce vibration and rattling noises
• Symptoms include loose panels, shifting components, or a screw that won't tighten

• Disconnect power and allow any hot surfaces to cool before servicing
• Wear cut-resistant gloves and eye protection
• Match length and thread to the original; replace like-for-like
• Start threads by hand to avoid cross-threading; do not overtighten

This power cord assembly supplies AC power from the wall outlet to your appliance. Replacing a frayed, heat-damaged, or loose cord restores safe, reliable operation and can eliminate intermittent power loss.

• Carries line voltage and ground into the unit to power controls and components
• Routes electricity safely into the cabinet to protect internal wiring
• Replace at the first sign of damage to reduce shock or fire risk

• Disconnect power at the outlet/breaker before servicing
• Compare the new cord to the original; transfer any clips or grommets from the old cord if needed
• Route and secure the cord exactly as original; keep clear of sharp edges and moving parts
• Ensure all connections are fully seated and the ground is properly secured before restoring power

This sub PCB assembly is an electronic control board that processes inputs and switches components, coordinating specific appliance functions. Replacing a failed board can restore normal operation and resolve dead controls, error codes, or intermittent, unpredictable behavior. What it does:

• Distributes and regulates control power and switches loads via onboard relays/triacs
• Interprets signals from sensors and the user interface to execute commands
• Coordinates timing and operation of related components per the appliance's program logic
• Failure may present as no power, won't start, unresponsive or flickering display, random beeps, or recurring error codes

• 1 sub PCB assembly

• Disconnect power to the appliance before servicing; verify no voltage is present
• Use ESD protection and handle the board by the edges
• Photograph wiring; transfer connectors one at a time and ensure they are fully seated
• Secure the board with existing fasteners/standoffs; perform any required reset or diagnostic per your model's service info

Replacement tray cover assembly that restores the dispenser tray's function and appearance. Helps contain spills and keeps debris out of the tray area for cleaner operation and easier maintenance. What it does:

• Covers the dispenser/drip tray to contain spills and prevent debris buildup.
• Helps direct liquids into the tray and away from internal components.
• Commonly replaced when the cover is cracked, warped, broken, or missing.
• Can improve appearance and reduce odors caused by trapped residue.

• Follow the manufacturer's service manual for exact removal and replacement steps.
• Disconnect power and water before servicing nearby components.
• Use gentle prying to release clips; avoid excessive force to prevent damage.
• Inspect mating clips and support features; replace any broken fasteners before installing.

This gas valve assembly controls and shuts off the flow of gas to your appliance's burner system, enabling safe ignition and steady heat. Replacing a sticking or failing valve restores reliable heating performance and consistent flame control.

• Regulates gas flow to the burner(s) as commanded by the control/thermostat
• Works with the igniter to light the flame
• Helps maintain stable gas supply for consistent heating
• Failure symptoms include no ignition, igniter glowing with no flame, intermittent heat, or a weak/uneven flame

• Disconnect power and shut off the gas supply before servicing
• Allow the appliance to cool and work in a well-ventilated area
• Transfer any fittings or brackets from the original valve if required
• After installation, restore gas and check all connections for leaks with a soapy-water solution

This hinge bolt secures the hinge to the appliance cabinet or door, keeping alignment true and motion smooth. Replacing a stripped, missing, or corroded bolt helps restore proper door operation and reliable closing.

• Fastens the hinge to support and stabilize the door
• Helps maintain alignment for smooth opening and closing
• Replaces damaged, stripped, or missing hardware

• Disconnect power to the appliance; shut off water supply if applicable
• Support the door to prevent strain on remaining hardware; enlist a second person if needed
• Note the order/orientation of any shims or washers and transfer them during reassembly
• Start threads by hand to avoid cross-threading; tighten securely without overtightening