Lsxc22426s Parts

This is a replacement drain tube assembly that directs water from the appliance tub to the drain pump or household drain, helping restore proper water removal and reduce leaks. It's a direct-fit service part used in the drainage system. What it does:

• Channels wastewater away from the tub to the drain pump or drain line
• Helps prevent pooling or slow draining caused by a damaged or disconnected tube
• Restores a sealed path to reduce leaks at the tub-to-pump connection
• Suitable when the original drain tube is cracked, split, collapsed, or leaking

• One drain tube assembly as shown

• Disconnect power and water before beginning any repair to avoid shock or flooding
• Inspect and clean mating surfaces and clamps; replace clamps if corroded or damaged
• Ensure correct routing and secure connections to prevent kinks and leaks

This cap assembly for the duct secures and seals a dryer/exhaust duct connection to restore proper airflow and help prevent leaks. Designed to replace a worn or damaged duct cap and keep the vent path intact. What it does:

• Caps and secures the duct outlet to maintain a tight connection and reduce air leakage
• Helps direct exhaust airflow through the duct instead of escaping at the connection
• Can reduce lint and moisture escaping at a faulty or damaged duct joint
• Commonly replaced when the original cap is cracked, broken, or no longer holds the duct in place

• One cap assembly

• Disconnect and power off the appliance before servicing; follow the manufacturer's service manual
• Basic hand tools typically required; check panel or vent access before starting
• Inspect surrounding duct and fasteners; replace damaged clamps or tape as needed

This evaporator assembly replaces the sealed evaporator coil and housing that cools the freezer compartment and helps maintain proper low temperatures. Restores cold-air circulation and supports frost-management in frost-free refrigerators. What it does:

• Absorbs heat from the freezer compartment so refrigerant can carry heat away
• Works with the evaporator fan to circulate cold air through the cabinet
• Failing or damaged evaporators can cause warm/freezer not cold, frost buildup, or excessive frost/ice on coils
• Helps stop drip or pooling water from improper defrost when the evaporator assembly is functioning

• One evaporator assembly

• Service may require access to the sealed refrigeration system; follow manufacturer repair procedures
• Handle carefully to avoid puncturing the coil; damaged coils require sealed-system service
• Disconnect power before servicing and wear appropriate PPE when accessing internal components

This water valve assembly controls the flow of water into the appliance, restoring reliable fill and stopping unwanted leaks or no-fill conditions. It's a direct-replacement component designed for easy swap-in repairs. What it does:

• Opens and closes to allow water into the appliance when a cycle or dispenser calls for it
• Restores normal water fill for ice makers, dispensers, or wash cycles
• Stops unwanted or continuous filling caused by a failed valve
• Helps eliminate leaks or dripping when the valve seal is compromised

• Disconnect power and shut off the water supply before beginning work
• Handle electrical connectors and solenoid terminals carefully; replace any damaged wiring or connectors
• After installation, restore power and water, then run a test cycle and check all connections for leaks

This cap assembly seals and protects the dryer/refrigeration vent duct where it exits the appliance, helping direct airflow and keep outside air, moisture, and debris out of the duct system. It's a direct-replacement external vent cap. What it does:

• Covers and seals the duct outlet to maintain proper airflow and reduce drafts
• Helps prevent moisture, pests, and debris from entering the duct
• Supports consistent venting to help avoid lint buildup and reduced performance
• Replaces a damaged, cracked, or missing duct cap to restore a proper exterior seal

• One cap assembly for the duct outlet

• Disconnect power and, if applicable, gas before beginning any work
• Remove old cap carefully; wear gloves to protect against sharp edges and lint
• Check and clear the vent path of lint and debris while replacing the cap

This condenser assembly is the factory-style replacement condenser wiring and support used in compatible LG refrigerators to restore proper condenser connections and securement. It helps maintain reliable cooling system electrical routing and component support. What it does:

• Provides the correct wire routing and connections for the refrigerator condenser area
• Secures condenser components in place to prevent vibration and wear
• Restores proper electrical paths for condenser-related circuits to help the compressor/fan operate as intended
• Helps address symptoms like intermittent cooling, unusual vibration, or loose wiring in the condenser compartment

• One condenser assembly as shown

• Disconnect power and follow manufacturer safety procedures before starting work
• Inspect surrounding components (fan, compressor mounts, tubing) while replacing this assembly

This cover assembly replaces a damaged or missing outer panel to protect internal components and restore the appliance's finished appearance. It provides a secure enclosure that helps prevent debris and accidental contact with underlying parts. What it does

• Covers and protects controls, wiring, and internal components from dust, spills, and physical damage
• Restores the appliance's exterior look after cracks, breaks, or missing panels
• Helps reduce vibration noise caused by loose or damaged panels
• Keeps access points sealed so controls and fasteners stay secured

• Disconnect power (unplug appliance or switch off breaker) before starting any repair
• Remove any adjacent panels or bezels as needed to access mounting screws—typically requires basic hand tools (screwdriver, nut driver)
• Handle plastic tabs and clips carefully; brittle clips can break when reinstalling
• If fasteners or clips are damaged, replace them to ensure a secure fit.

A replacement refrigerator door handle assembly that restores a secure, easy-to-grip door pull and keeps the door opening and closing smoothly. Designed to match the original fit and finish for a factory look. What it does:

• Replaces a damaged, cracked, or loose door handle to restore safe, reliable door operation
• Provides a secure grip for opening and closing the refrigerator door
• Helps maintain proper door seal by allowing normal use without forcing or wiggling
• Matches the original exterior appearance and mounting locations

• Basic hand tools are typically required; unplug or disconnect power to the appliance before starting
• Support the door while removing or installing the handle to avoid damage or injury
• Keep fasteners and trim in a safe place during install; follow manufacturer torque and alignment guidance

This door basket is the upper-rack basket assembly that holds small items securely in the dishwasher, helping keep utensils and small dishes positioned for thorough cleaning. It replaces a damaged or worn basket to restore proper loading. What it does:

• Secures small items and utensils in the upper rack so they stay in place during wash cycles
• Prevents items from falling into the lower rack or blocking spray arms, which can reduce cleaning performance
• Replaces cracked, warped, or broken basket sections that no longer support dishes safely
• Helps maintain proper water flow and coverage by keeping load items organized

• One door basket (upper rack)

• Designed to snap or slide into the upper rack;
• Inspect surrounding rack components and track for wear before installing
• Disconnect power and follow basic dishwasher safety procedures if service access requires removing panels
• Use common hand tools;

This mechanical mounting band secures a bracket assembly inside the appliance to keep components aligned and reduce vibration. It restores proper bracket positioning so moving parts run quietly and reliably. What it does:

• Holds a bracket or component assembly in place to maintain proper alignment
• Dampens movement and reduces vibration-related noise or rattling
• Prevents excess wear by keeping parts from shifting during operation
• Helps maintain correct clearances to avoid interference or rubbing

• Disconnect power before inspecting or replacing internal parts
• Remove only the fasteners necessary to access the bracket; keep track of hardware
• Secure all fasteners to the manufacturer's torque or snug specification
• Replace the band if bent, cracked, or missing to restore proper fit and function

This case assembly for the refrigerator control area houses and protects the control board and user interface components, helping keep electronics secure and accessible for diagnostics or replacement. What it does:

• Protects the control board and wiring from damage, dust, and moisture
• Provides mounting points and alignment for the user interface and controls
• Keeps the control area organized for service access and replacement
• Helps maintain proper airflow around control electronics where applicable

• Power off and unplug the appliance before servicing to avoid shock or injury
• Handle the control housing and any attached ribbons or connectors carefully to avoid damage
• Keep screws and small fasteners organized; verify fit before final assembly
• Follow manufacturer instructions and ESD precautions

This upper hinge assembly secures and pivots the refrigerator door, restoring proper alignment and smooth opening/closing. Durable replacement for worn or damaged upper door hinge hardware to help prevent sagging and gaps. What it does:

• Supports the top of the refrigerator door and provides the pivot point for opening and closing
• Restores proper door alignment to help maintain an even seal and prevent cold air loss
• Eliminates squeaks, binding, or resistance caused by worn hinge components
• Helps prevent door sag and uneven gaps that can interfere with operation

• Unplug the appliance and remove food from the door shelves before beginning work
• Support the door (use a second person or a block) while removing and installing the hinge to avoid dropping or damaging the door
• Keep fasteners and any bushings/towels organized; some models reuse original screws or pins
• Adjust hinge screws per the manufacturer's instructions

This damper cushions and isolates the refrigerator compressor to reduce vibration and noise for smoother operation. It helps maintain stable compressor mounting and prevents metal-to-metal contact that can cause wear or rattling. What it does:

• Absorbs compressor vibrations to reduce noise and movement
• Helps protect the compressor housing and mounting points from shock
• Can reduce rattling or knocking sounds originating near the compressor area
• Supports proper alignment of the compressor assembly during operation

• One compressor damper (mounting isolator)

• Turn off power at the breaker and unplug the appliance before servicing
• Inspect mounting area and hardware; replace any damaged fasteners before installing the damper
• Position the damper on the compressor mount as shown in the service manual and secure per OEM guidance

The Auger Motor is an OEM part for LG refrigerators. It is responsible for dispensing ice from the icemaker into the ice bucket. 

Symptoms of a bad auger motor include:

• Slow or incomplete ice filling of the ice bucket
• Ice clumping or jamming in the auger assembly 
• Grinding or rubbing noises coming from the icemaker region
• The icemaker not producing any ice at all

Causes of a bad auger motor can be wear and tear over time, freezing or ice buildup preventing proper operation, or failure of internal motor components. 

This OEM LG part is also compatible with select Sears/Kenmore models. 

This bucket cover restores the top enclosure of the washer tub so water stays contained and the wash basket operates as designed. It helps protect laundry and internal components from splashes and debris. What it does:

• Fits over the wash bucket to cover the tub opening and direct water flow
• Helps prevent water spray and leaks during fill and spin cycles
• Keeps clothing and loose items from entering the tub gap
• Contributes to stable basket operation and reduces direct contact with internal parts

• Disconnect power and water supply before beginning any repair
• Remove the cabinet or access panel as required by your model to reach the bucket area
• Use appropriate hand tools; support the tub/basket to avoid displacement during removal/installation
• Follow OEM instructions for torque, alignment, and reassembly