Lt5100xvwo Thin Twin Parts

This hinge pin assembly secures and guides a refrigerator or freezer door, restoring proper alignment and smooth opening. It replaces worn or bent pins so the door closes evenly and reduces rubbing or sagging. What it does:

• Acts as the pivot point for the appliance door, supporting door weight and movement
• Restores correct door alignment to improve sealing and reduce gaps
• Reduces rubbing, scraping, or uneven closing caused by a worn or bent hinge pin
• Helps prevent accelerated wear to door seals and hinge components when functioning properly

• One hinge pin assembly

• Disconnect power and remove food/contents from the door area before starting
• Support the door while removing or installing the hinge to prevent dropping or injury
• Typical installation uses basic hand tools; do not force parts—inspect mating hinge surfaces for damage

This white front door panel replaces a damaged or worn exterior door and restores the appliance's appearance and sealing surface. It matches the original panel shape and finish for a factory look. What it does

• Replaces a cracked, dented, chipped or otherwise damaged front door panel
• Restores the appliance's exterior finish and helps maintain proper door alignment
• Provides the factory surface for attaching original trim, hinges and handles
• Improves appearance after impact or long-term wear

• One white front door panel

• Disconnect power and water before beginning work
• Some trim, handles or hinges may need to be transferred from the old door; inspect fasteners and hardware
• Handle panels carefully to avoid scratching the finish during installation
• Tighten fasteners to manufacturer torque specs and check door alignment after installation

This hose coupling connects a flexible appliance hose to the appliance plumbing, restoring a secure water connection and preventing leaks. Ideal when a worn or damaged coupling causes drips or loose hose fit. What it does:

• Provides a secure connection point between an appliance hose and the appliance inlet
• Replaces cracked, broken or corroded couplings that can leak or allow the hose to detach
• Restores proper hose sealing to reduce water drips at the connection
• Compatible with the original inlet connection type and mounting orientation

• Turn off and disconnect appliance power and shut off the water supply before replacing
• Remove the old coupling and clean the mating surfaces; inspect hose and clamps for wear
• Use proper clamps and hand-tighten; avoid over-tightening which can damage fittings

Spring-style hose clamp that secures flexible appliance hoses to fittings, helping keep connections tight to reduce leaks and maintain proper water flow. Use it to replace a worn or damaged clamp and restore a reliable hose seal. What it does:

• Compresses around a flexible hose to lock it onto barbs or fittings
• Helps prevent drips, leaks, and water pooling at hose connections
• Keeps hoses from slipping off during appliance operation
• Useful when a clamp is corroded, stretched, or no longer holds tension

• Disconnect power and shut off water to the appliance before starting any repairs
• Use pliers to compress the clamp for removal and installation; keep hands and face clear when releasing tension
• Inspect the hose and fitting for damage; replace the hose if cracked or excessively worn

This 10-circuit connector housing provides a secure plug-style connection for the appliance wiring harness, restoring reliable electrical contact where the original plastic connector is cracked or melted. It helps ensure circuits stay seated and insulated. What it does:

• Replaces a damaged or cracked 10-circuit plastic connector housing to restore a proper plug connection
• Secures wiring harness terminals to prevent intermittent power or signal loss
• Keeps electrical contacts insulated from vibration and moisture
• Useful when the mating connector body is broken, burned, or otherwise unusable

• One 10-circuit connector housing

• Disconnect power to the appliance before starting any repairs
• Verify terminal pin type and wiring orientation before removing the old housing; take a photo for reference
• This listing is for the housing only; transfer existing terminals/pins or replace pins with exact matches as needed

This console lock secures the appliance control console and helps prevent accidental changes to settings. It replaces a worn or broken console latch so the control panel stays closed and functions as intended. What it does:

• Secures the control console or access panel to prevent unintended opening
• Restores a solid latch action when the existing lock is loose, broken, or missing
• Helps prevent accidental button presses or changes to selected cycles
• Fits into the control console area and engages with the console catch mechanism

• One console lock assembly

• Disconnect power to the appliance before attempting any repair
• Removal typically requires access to the control console—refer to your model-specific service manual
• Handle plastic tabs and clips carefully to avoid breakage during removal and installation

This lid latch secures the appliance lid and, on interlock-equipped models, signals that the lid is closed so the cycle can run safely. It restores proper closure and dependable operation when the original latch is worn or broken. What it does

• Latches the lid closed to prevent unintended opening during operation
• Engages the lid switch/lock circuit where used, allowing the cycle to start or continue
• Helps maintain alignment between the lid and strike/keeper for reliable closure
• Common symptoms include: lid won't stay closed, unit won't start or advance, intermittent stopping when the lid is bumped

• 1 lid latch

• Disconnect power before servicing; turn off water supply if applicable
• Access the latch, remove retaining screws/clips, and note orientation for reassembly
• Install the new latch and align it with the lid strike/keeper; reuse original hardware if required
• Close the lid and run a short test to ensure proper engagement and operation

This replacement sleeve is a small shaft bushing that helps the drum/shaft rotate smoothly and keeps moving parts aligned to reduce wear and noise. It restores proper fit where a worn sleeve causes rubbing or play. What it does:

• Acts as a bearing surface between the shaft and housing to reduce friction
• Helps prevent metal-on-metal contact that can cause squeaks or scraping noises
• Restores correct alignment to reduce wobble or uneven drum movement
• Protects surrounding seals and components from premature wear

• One sleeve

• Disconnect power before starting and follow the appliance service manual for disassembly steps
• Inspect adjacent parts (shaft, bearings, seals) and replace if worn to ensure long-term performance
• Use proper tools and keep track of fasteners; some disassembly of the drum or cabinet may be required

This connector is an insulated electrical harness terminal that joins appliance wiring to restore a secure electrical connection and help prevent intermittent power or arcing. It's a direct-replacement style used on select Whirlpool appliances. What it does:

• Provides a secure, insulated connection between two wires or a wire and a component terminal.
• Helps stop intermittent power, flickering, or loss of function caused by loose or damaged terminals.
• Reduces risk of arcing and overheating at a compromised connection point.
• Matches OEM fit/shape to maintain proper routing and strain relief where applicable.

• Turn off and unplug the appliance (or shut off breaker) before inspecting or replacing electrical parts.
• Inspect surrounding wiring and terminals for heat or corrosion; replace damaged wiring as needed.
• Use proper crimping or terminal tools and secure strain relief; verify firm, no-play connections before restoring power.

This rotary timer controls cycle selection and timing for the appliance, restoring proper cycle sequencing and user-selected settings. It replaces a worn or non-responsive timer to help the unit advance through cycles as commanded. What it does:

• Rotates to select and advance program settings so the appliance runs the chosen cycles
• Sends position signals to other components so operations start and stop at the correct times
• Common symptom: selector won't stay on a chosen setting or cycles do not advance properly
• Common symptom: timer knob is hard to turn, skips positions, or is unresponsive

• Disconnect power before accessing the control console to avoid shock
• Remove console trim or panel per your model's service instructions to reach the timer
• Reuse original knob and mounting hardware; ensure proper wiring connections match original terminals

This agitate gear washer is a small flat washer used with the washer's agitate gear to ensure proper spacing and smooth engagement. It helps maintain correct gear alignment so the agitator can move laundry effectively. What it does:

• Provides a stable spacer between the agitate gear and mating components to prevent excess play
• Helps maintain correct gear alignment for consistent agitator movement
• Reduces metal-on-metal contact that can cause noise or premature wear
• Commonly replaced when the agitator feels loose, makes grinding noise, or causes uneven agitation

• High-level replacement: remove agitator/gear per service manual to access washer; reinstall in original orientation
• Use manufacturer torque/settings for reassembly; do not overtighten
• Inspect adjacent gear and splines for wear; replace any damaged components
• Disconnect power and follow safety procedures before servicing the washer